GAS-350 · Lesson 2 of 12 · 23 min

A study plan that works

▶ Video coming soon A video version of this lesson is on the way.

At the end of the first Tuesday, Maureen gave Luis and Grant a sheet with three columns: topic, how sure you are, how many questions you expect. "Fill it in tonight," she said, "honestly. Then bring it back next week and we'll build your plan from it." Luis filled it in at his kitchen table and was surprised. He had marked himself very sure on residential appliances, propane and venting, which he worked on every week, and unsure on large-boiler controls, flame safeguards, elevated-pressure piping and the B149.3 approval of field-built equipment, which he met only on Maureen's jobs. "That's normal," Maureen said the next Tuesday. "People study what they already know, because it feels good. The plan's job is to stop you doing that."

This lesson sets out a way to plan the weeks before a certification exam: start from what the exam covers, find out what you do not know, spread the work over time, practise under exam conditions, and prepare the code book. It ends with the habits that help on the day and the support that makes the difference for many candidates.

Start from what the exam covers

Start from the curriculum, because the exam is built from it. For the G.1, that means the large-appliance modules of the TSSA-approved curriculum and the codes they refer to, together with all the G.2 material a G.1 must still know. Luis listed the modules from his course outline down the left side of a page and, against each one, wrote the program course where he had met it: GAS-310 for burners and flame safeguards, GAS-320 for boilers, rooftop units and makeup air, GAS-330 for regulators, meters and elevated-pressure piping, GAS-340 for troubleshooting, and the earlier courses for everything else. The list became the outline of his plan.

Next, rate each topic honestly. A simple scale works: 3 if you could teach it, 2 if you could answer most questions on it, 1 if you would be guessing. Then multiply each rating's gap, 3 minus the rating, by the topic's share of the exam. The result tells you where study time buys the most marks. A topic with many questions and a low rating comes first; a topic you could teach comes last, however much you enjoy it.

Worked problem

Where does study time buy the most marks?

Suppose a candidate's sheet shows four topic areas. Venting and air supply is expected to be 15 of 100 questions and rated 3. Commercial burners and controls is 20 questions and rated 1. Piping, regulators and meters is 20 questions and rated 2. Codes and regulations is 25 questions and rated 2. Rank the topics by priority.

Show solution
  1. Priority is the gap times the number of questions:
  2. Venting: (3 − 3) × 15 = 0.
  3. Burners and controls: (3 − 1) × 20 = 40.
  4. Piping, regulators and meters: (3 − 2) × 20 = 20.
  5. Codes and regulations: (3 − 2) × 25 = 25.

Answer: Burners and controls first (40), then codes (25), then piping (20). Venting, the topic the candidate likes best, needs only a quick review near the end. The arithmetic is rough, but it turns a feeling into a plan.

Spread it out

Ten hours of study spread over ten days teaches more than ten hours in one weekend. Memory researchers call it the spacing effect: information that is reviewed several times with gaps in between is kept far longer than information crammed in one session. The practical rule is to study a little most days, return to each topic several times, and leave the last week for practice tests and review rather than new material.

A realistic plan counts the hours that are actually available. Luis works full days, often with an on-call week in the rotation, and has two young children. He decided on about six hours a week: an hour on four weekday evenings and two hours on Saturday mornings, with the Tuesday certification nights counted as study. Over twelve weeks that is about 72 hours, which is enough for a candidate who has already finished the training and works in the trade every day. A candidate starting with weaker foundations needs more, or more weeks.

A twelve-week study calendar drawn as a row of twelve columns. Weeks 1 and 2 are labelled: inventory, code book tabs, structure of the codes. Weeks 3 to 8 are labelled: weak topics first, with a short review of an earlier topic each week shown as small return arrows. Weeks 9 and 10 are labelled: calculation practice and timed question sets. Week 11 is labelled: full practice exam, error log. Week 12 is labelled: review the error log, rest, exam day. Under the calendar a bar shows about six hours each week.
A twelve-week plan. New material comes early, earlier topics return every week, and the last weeks are for practice and review.
Luis's twelve-week outline.
WeeksWhat happensHow Luis did it
1 to 2Inventory, rate topics, set up the code bookRated the modules, tabbed his B149.1 and B149.3, read the regulation's certificate scopes
3 to 8Weakest topics first; one earlier topic reviewed each weekFlame safeguards and BMS, large boilers, elevated pressure, field approvals; then appliances and venting
9 to 10Calculations and timed question setsLesson 10 problems, 25-question sets in 45 minutes
11Full practice exam, marked, error logMaureen's practice exam on a Saturday morning
12Review the error log, restLight review, early nights, exam day

Active study beats rereading

Rereading notes feels productive and is not. The methods that work all make the brain retrieve the information instead of just recognizing it:

  • Practice questions. Answer questions, check them and work out why each wrong answer was wrong. This course's quizzes and the practice set in lesson 11 are a start; writing your own questions, as Maureen made her group do, is even better.
  • Explaining aloud. Explain a topic to someone else, or to the dashboard of the truck, without notes. Where you stumble is where you do not know it.
  • Flash cards for numbers and definitions that must be recalled quickly: specific gravities, heating values, flammable limits, the theoretical air volumes, the certificate scopes, typical pressures.
  • Drawing from memory. Sketch a gas train, a ladder diagram or a two-stage propane system from memory, then compare it with the figure.
  • Mixing topics. A set of questions that jumps between venting, controls and propane is harder than a set on one topic, and that is the point: the exam mixes them.

The code book is a tool, so learn to use it

The B149.1 code book is allowed in the G.3 and G.2 exams with dividers and highlighting only, and many candidates waste that advantage by opening it for the first time in the exam room. A candidate should know the code's structure: the scope and definitions at the front, the general requirements, then the sections on piping, appliances, venting and air supply, then the annexes. Tabs on the sections you use most, the definitions, the index and the sizing tables, save minutes. Highlighting the key words in a clause you always forget, such as an exception, helps you find it again. Check the preparation guide for the G.1 to see what you may bring, and practise both ways: with the book, and from memory.

A good way to practise lookups is a ten-minute drill. Take ten questions that need a number from the code, set a timer, and find each one. Record how long each took. Questions that took more than a minute show where another tab, or more familiarity, is needed. By the end of his drills Luis could find most answers in under 40 seconds.

Reading a multiple-choice question

Most marks lost on multiple-choice exams are not lost through ignorance. They are lost by misreading. A routine helps:

  • Read the last sentence first. It is the actual question. Then read the whole stem with the question in mind.
  • Underline the qualifiers: not, except, first, most likely, minimum, maximum, always, never. "Which is NOT a cause" reverses the question.
  • Answer before looking at the options, if you can. Then find your answer among them. This protects you from a distractor that looks right.
  • Eliminate. If you are unsure, cross out the options you know are wrong. Two left gives a fifty-fifty chance; one left is the answer.
  • Check the units. A question in kilopascals with an answer in inches of water column, or in Btu per hour with an answer in cubic feet per hour, is a common trap.
  • Mark and move. If a question is taking too long, choose the best answer you have, mark it and come back at the end. Never leave a blank.

Be careful with answers that use absolute words such as always, never, only and all. In a trade governed by exceptions they are often wrong, but not always: "always shut off the gas before replacing a gas valve" is correct. Judge each option on its content, not on its wording.

Practise under real conditions

At least once, and preferably twice, before the exam, write a full-length practice exam under the same conditions: the same number of questions, the same time, the same books, no phone, in one sitting. A full-length test shows things that short sets do not: whether your pace holds for three or four hours, when your concentration fades, whether you need to eat or stretch at the halfway point, and whether your book is set up the way you need it. Maureen scheduled hers for Saturday, November 14, four days after the last certification night, so that Luis and Grant would have their results in time to build the last weeks of their plans around them. Lesson 11 describes what happened.

Looking after the candidate

Sleep, food and stress affect exam scores as much as an extra week of study. The week before the exam is the wrong time to change your sleep pattern or stay up late cramming. Plan the route to the exam centre and do it once in advance if it is unfamiliar. Eat before you go, and take water if it is allowed. If anxiety is a problem, practice tests help, because the exam room becomes familiar; slow breathing for a minute at the start helps too. A candidate with a learning disability or another condition that affects exams can ask TSSA for an accommodation such as extra time, and must ask well before booking, with the documentation they require.

Family and work matter as well. Luis told his manager and his family what the next twelve weeks would look like, and Maureen kept him off the on-call rotation for the two weeks before his exam date. A study plan that depends on nobody needing you is a plan that will fail.

Studying with other people

Maureen's certification nights were a study group with a teacher. A study group of two or three candidates works well if it has a plan: each person prepares one topic each week and teaches it to the others, and the group finishes by answering questions the others wrote. Explaining a topic is the best test of understanding, and writing questions forces you to think about what could be asked and what the wrong answers would be. Groups work badly when they become social evenings, or when one person does all the work. Jonah and Ayesha, who sat in at the back, found that the questions Luis and Grant asked taught them more than the answers did.

Getting the most from each practice question

A practice question is worth far more than the mark it carries, if you use it properly. After answering a set, go back to every question, not just the ones you got wrong, and ask three things. Why is the right answer right, in one sentence? Why is each wrong option wrong, and what mistake would lead someone to choose it? Could the question have been asked another way? A question answered correctly by a lucky guess counts as wrong for study purposes.

Worked problem

Reviewing one practice question

A practice question asks: "A furnace locks out after three tries. The flame lights each time and goes out after about six seconds. What is the most likely cause?" The options are a cracked heat exchanger, a dirty flame rod, a stuck-open pressure switch and a failed blower capacitor. Luis chose the flame rod and was right. How should he review it?

Show solution
  1. Why it is right: the flame lights, so gas and ignition work; the valve closes at the end of the trial, so the flame is not being proven; a dirty rod gives a weak signal.
  2. Why the others are wrong: a cracked heat exchanger usually shows when the blower starts, after the flame is proven; a stuck pressure switch stops the sequence before ignition; the blower is not involved until after the blower-on delay.
  3. Another way to ask it: "Which reading would confirm the cause?" A flame signal below the board's minimum.

Answer: Three minutes spent on one question he got right taught him the sequence of operation better than ten more questions would have. Maureen asked the group to review every practice set this way.

Common mistakes

  • MistakeStudying the topics you enjoy most.

    InsteadRate each topic and spend time where the gap times the number of questions is largest.

  • MistakeCramming in the last week.

    InsteadSpread study over weeks and return to each topic several times.

  • MistakeRereading notes and calling it study.

    InsteadRetrieve: answer questions, explain aloud, draw from memory.

  • MistakeOpening the code book for the first time at the exam.

    InsteadLearn its structure and tab it weeks before; practise lookups against a timer.

  • MistakeMissing a NOT or an EXCEPT in the stem.

    InsteadRead the question first and underline the qualifiers.

  • MistakeNever writing a full-length practice exam.

    InsteadWrite at least one under real conditions, in one sitting.

Summary and key terms

  • A study plan starts from what the exam covers: the curriculum modules or the bulletin's content outline.
  • Rate each topic honestly and give most time to topics with many questions and low ratings.
  • Spread study over weeks, about six hours a week for twelve weeks for a working candidate who has finished the training, and return to earlier topics each week.
  • Study actively with practice questions, explaining aloud, flash cards, drawing from memory and mixed question sets.
  • Learn the code book's structure, tab it as the rules allow and practise lookups against a timer.
  • Read the question first, underline qualifiers, answer before looking at the options, eliminate, check units, and mark and move.
  • Write at least one full-length practice exam under real conditions.
  • Sleep, food, family and accommodation requests are part of the plan.
Spacing effect
The finding that study spread over several sessions with gaps is remembered better than the same study in one session.
Active recall
Studying by retrieving information from memory, for example by answering questions, instead of rereading.
Qualifier
A word in a question, such as not, except, first or minimum, that changes what is being asked.
Lookup drill
Timed practice at finding answers in a code book.
Accommodation
A change to exam conditions, such as extra time, granted to a candidate with a documented need.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. Why does a topic you rate 3 come last in the plan?

    Show answer

    Its gap is zero, so study time there buys the fewest marks.

  2. What is the spacing effect?

    Show answer

    Information reviewed several times with gaps is remembered better than information crammed in one session.

  3. What should you do first when reading a multiple-choice question?

    Show answer

    Read the last sentence, the actual question, then the stem with the question in mind.

  4. Why write a full-length practice exam?

    Show answer

    To test pace, concentration and book set-up over the whole sitting.

  5. Name three active study methods.

    Show answer

    Practice questions, explaining aloud, flash cards, drawing from memory or mixed sets.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz