ROOF-110 · Lesson 8 of 12 · 25 min
Ladders, hoists and material handling
▶ Video coming soon A video version of this lesson is on the way.
A roofing crew moves a staggering amount of material. A single house re-roof can mean tearing off two or three tons of old shingles and carrying up a similar weight of new ones. The Ashgrove Plaza re-roof will take off several truckloads of old built-up roofing and gravel and bring up insulation, cover board, membrane rolls, metal, adhesives and propane. All of it moves between the ground and the roof by ladder, hoist, conveyor or crane, and all of it has to be stored on a roof that was designed to keep out weather, not to act as a warehouse. Injuries from this side of the work are common: falls from ladders, strains from lifting, crushed hands at hoists, materials falling on people below and roofs damaged by overloading.
"Most roofers I've known who got hurt badly weren't hurt doing roofing," Dana told Rory on his first loading day. "They were hurt getting up there, or getting stuff up there."
Choosing and inspecting ladders
Ladders are the most common way onto low roofs and the most common source of falls on residential jobs. Roofers mainly use extension ladders to reach eaves, and stepladders for low work on the ground or inside. Choose the ladder for the job:
- Long enough to reach the landing and extend the required distance above it, without using the top sections that the manufacturer says not to stand on.
- Rated for the load: the worker plus tools and materials. Use ladders with a duty rating of Type I (250 pounds) or higher, such as Type IA (300 pounds) or IAA (375 pounds), for construction.
- Non-conductive (fiberglass) side rails wherever the ladder could come near overhead power lines or other electrical equipment.
- In good condition: no cracked or bent rails, missing or loose rungs, damaged feet, broken locks or frayed rope.
Inspect the ladder before each use. A ladder with a defect is tagged "do not use" and taken out of service. Never paint a wooden ladder, which hides cracks, and never splice two short ladders together to make a long one.
Setting up an extension ladder
The angle matters. Too steep, and the ladder can tip backward when the worker leans out; too shallow, and the feet can slide out. OSHA requires non-self-supporting ladders to be used at an angle where the horizontal distance from the top support to the foot is about one-quarter of the working length of the ladder (the 4 to 1 rule), which gives an angle of about 76 degrees (29 CFR 1926.1053(b)(5)(i)). When a portable ladder is used to reach an upper landing such as a roof, its side rails must extend at least 3 feet above the landing, or the ladder must be secured at the top with a grab rail provided (29 CFR 1926.1053(b)(1)). Ladders must be secured or stabilized so they cannot be displaced.
Worked problem
Setting up a ladder at the 4 to 1 angle
The eave of a Linden Street house is 18 ft above level ground. How far out should the ladder base be using the 4 to 1 rule? What length of ladder is needed to the eave, and in total if the side rails must extend 3 ft above the eave?
Show solution
- Base distance: 18 ÷ 4 = 4.5 ft.
- Length to the eave: √(18² + 4.5²) = √(324 + 20.25) = √344.25 ≈ 18.6 ft.
- Total length: 18.6 + 3 ≈ 21.6 ft of ladder in use.
- An extension ladder also needs its sections to overlap, so a 24-foot extension ladder is the shortest that will work.
Answer: Set the base 4.5 ft out. About 21.6 ft of ladder is needed in use, so choose a 24-foot extension ladder.
A quick field check for the angle is to stand at the base with your toes against the ladder feet and stretch your arms straight out: your palms should just reach the rung at shoulder height. Other set-up rules:
- Set the feet on firm, level ground; use levelers or a stable base on slopes, and never set the ladder on boxes, bricks or loose material.
- Rest the ladder on a solid surface at the top, not on a gutter, which can bend or break. Use a standoff or a ladder stabilizer that spans the gutter.
- Tie the top of the ladder off to the structure, or have another worker hold the base until it is tied off.
- Keep the area around the base clear and, near traffic or doors, barricade it.
- Look up before raising a ladder, and stay well clear of overhead power lines.
Climbing and working from ladders
Face the ladder when climbing, keep three points of contact (two hands and a foot, or two feet and a hand) and keep your belt buckle between the rails. OSHA requires workers to face the ladder when climbing or descending, to use at least one hand to grasp the ladder, and not to carry any object or load that could cause them to lose balance (29 CFR 1926.1053(b)(20) to (22)). Bundles of shingles, rolls of membrane and buckets of asphalt never go up a ladder on someone's shoulder. Use a hoist, a ladder hoist or a conveyor instead.
Stepping from a ladder to a roof is the riskiest moment. The extension above the eave gives you something to hold onto; step sideways onto the roof through the rails or beside the ladder, not over the top. Where a roof edge has a guardrail, the ladder should land at a gate or opening in the guardrail, never outside it. On steep roofs, the fall protection for the first worker must be set up so they are protected from the moment they leave the ladder.
Overhead power lines
Overhead power lines kill roofers every year, most often when an aluminum ladder, a metal flashing, a length of gutter or a hoist touches or comes close to a line. Electricity can arc across a gap to a conductive object without touching the line. OSHA requires that portable ladders with conductive side rails not be used where they could contact exposed energized equipment (29 CFR 1926.1053(b)(12)), and its rules for equipment near power lines require a clearance of at least 10 feet from lines up to 50 kV, with larger distances for higher voltages (for example 29 CFR 1926.1408 for cranes and hoisting equipment). Lines that run to houses (service drops) also carry dangerous voltage. Before setting up, look up, identify every line near the work, keep metal ladders well away, use fiberglass ladders, and call the utility to have lines de-energized, moved or covered if the work cannot stay clear.
Getting materials onto the roof
The best way to get materials onto a roof is to have them delivered there. Many roofing suppliers deliver shingles and other materials with a boom truck or a truck-mounted conveyor that places them directly on the roof. This removes most of the manual lifting and the trips up and down ladders. On commercial jobs, cranes lift pallets of insulation, membrane and equipment onto the roof, under a lift plan with a qualified operator, rigger and signaler, as you learned in TRD-105.
When delivery to the roof is not possible, roofers use:
- Ladder hoists: a powered platform that runs up a track ladder to the roof. Never ride a ladder hoist, never stand under it, and load it within its rated capacity.
- Roof hoists: a hoisting arm mounted at the roof edge with a winch or power unit, used to lift buckets, rolls and bundles.
- Conveyors: belt conveyors that carry bundles and rolls up at an angle to the roof.
- Material lifts and forklifts: telescopic handlers can place pallets on low roofs.
OSHA's rules for material hoists and base-mounted drum hoists (29 CFR 1926.552 and 1926.553) and the manufacturer's instructions govern roof hoists and similar equipment: rated capacity posted and never exceeded, the hoist assembled, anchored and counterweighted as the manufacturer specifies, a competent operator, and no riding on material hoists. Workers at the roof edge receiving loads must be protected from falling, normally by a guardrail with an opening or gate at the landing. Never use roofing materials as counterweights; use the counterweights designed for the hoist.
At the bottom of every hoist, the area under the load is barricaded so that nobody walks under it. Loads are rigged so nothing can slide out: bundles stacked in a bucket or cradle, rolls tied, metal tied in bundles with tag lines. Workers at the top stay behind the guardrail and pull the load in only after it has stopped.
Storing materials on the roof
A roof is designed to carry certain loads, such as snow, rain, the roof's own weight and maintenance workers. A pallet of roofing material can weigh more than a ton sitting on an area not much bigger than a kitchen table, which is many times the load per square foot the roof was designed for. Overloaded roofs can sag, crack or, in the worst cases, collapse. Ridgecap's rules for roof loading are:
- Spread loads out. On steep roofs, set small stacks of bundles along both sides of the ridge, never a whole pallet in one place, and lay bundles flat over the ridge or on a level bracket so they cannot slide.
- On low-slope roofs, place pallets and heavy items over beams, girders, columns or walls, as the owner's engineer or drawings direct, never in the middle of a span.
- Keep materials well away from roof edges and openings, and never inside the barrier zone.
- Secure light materials such as insulation boards and membrane rolls against wind with weights or tie-downs, and keep wrappers bagged.
- Never store materials on a roof that shows signs of sag, ponding or deck damage until it has been checked.
Worked problem
Checking a roof load
A pallet holds 25 rolls of base sheet at 88 lb each, plus a 45 lb pallet, on a footprint of 4 ft by 4 ft. Many low-slope roofs are designed for a minimum roof live load of about 20 pounds per square foot spread evenly. What load per square foot does the pallet put on the roof, and roughly how many times the design figure is that?
Show solution
- Total weight: 25 × 88 + 45 = 2,245 lb.
- Footprint area: 4 × 4 = 16 ft².
- Load per area: 2,245 ÷ 16 ≈ 140 lb per ft².
- Compared with 20 lb per ft²: 140 ÷ 20 = 7 times.
Answer: About seven times the evenly spread design figure. A concentrated load like this must sit over a beam or column, as the engineer directs, or be broken down and spread out. Design loads vary by building, so check the drawings or ask the owner.
Worked problem
Spreading bundles on a steep roof
A Linden Street roof needs 90 bundles of laminated shingles at 70 lb each. Dana allows no more than 6 bundles in any one stack along the ridge. How many stacks are needed, and how much does each stack weigh?
Show solution
- Stacks: 90 ÷ 6 = 15 stacks.
- Weight per stack: 6 × 70 = 420 lb.
- Total load: 90 × 70 = 6,300 lb, spread along both sides of the ridge.
Answer: 15 stacks of about 420 lb each, placed alternately on each side of the ridge over the rafters.
Manual handling
Even with hoists and conveyors, roofers lift, carry, push and pull all day. Back, shoulder and knee injuries are among the most common in the trade, and many of them build up over years. Good habits reduce the strain:
- Plan the lift: check the weight, the path and where the load will go. Clear the path of trip hazards.
- Get close to the load, bend your knees, keep your back straight and lift with your legs, keeping the load close to your body.
- Turn with your feet, not by twisting your back.
- Share heavy or awkward loads, such as membrane rolls and long metal, with a partner, and agree who calls the lift.
- Use carts, dollies and roll carriers on low-slope roofs instead of carrying.
- Watch the wind: an insulation board or a sheet of metal acts like a sail, and a gust can pull you off balance or off the roof.
Many safety organizations treat about 51 pounds as the most a worker should lift in ideal conditions, close to the body and at waist height, and much less when the lift is far from the body, high, low, twisted or repeated often. A bundle of laminated shingles often weighs more than that, which is one more reason to let machines do the lifting.
Common mistakes
MistakeCarrying bundles up a ladder on your shoulder.
InsteadUse a hoist, conveyor or rooftop delivery; keep three points of contact on ladders.
MistakeLeaning the ladder on the gutter.
InsteadRest it on a solid surface or use a standoff that spans the gutter.
MistakeUsing an aluminum ladder near a service drop.
InsteadUse fiberglass ladders and keep everything well clear of power lines.
MistakeUsing bundles of shingles as hoist counterweights.
InsteadUse only the counterweights designed for the hoist, secured as the manufacturer directs.
MistakeLanding a full pallet in the middle of a roof span.
InsteadPlace heavy loads over beams or columns, or spread them out.
Summary and key terms
- Set extension ladders at 4 to 1, with side rails 3 feet above the landing, secured against displacement.
- Inspect ladders before use, use the right duty rating and non-conductive rails near power, and keep three points of contact.
- Keep at least 10 feet from overhead lines up to 50 kV, and more for higher voltages.
- Roof hoists are assembled, counterweighted and loaded per the manufacturer, with protected landings and no riding.
- Spread loads on steep roofs and place concentrated loads over structure on low-slope roofs.
- Plan lifts, share heavy loads and use mechanical help to prevent strains.
- 4 to 1 rule
- Setting a ladder base one unit out for every four units of height to the support point.
- Ladder hoist
- A powered platform that carries materials up a track ladder.
- Roof hoist
- A hoisting arm mounted at the roof edge for lifting materials.
- Service drop
- The overhead power line that runs from a utility pole to a building.
- Point load
- A heavy load concentrated on a small area of a roof.
- Counterweight
- A weight that keeps a hoist from overturning under load.
Practice problems
Work each problem on paper first, then reveal the answer to check.
A support point is 16 ft high. Where should the ladder base be using 4 to 1?
Show answer
16 ÷ 4 = 4 ft from the wall.
How far must a ladder's side rails extend above a roof landing?
Show answer
At least 3 feet.
What is the minimum clearance from a 13.2 kV line for equipment under OSHA's general approach?
Show answer
10 feet (lines up to 50 kV).
What duty rating should a construction ladder have at minimum?
Show answer
Type I (250 pounds) or higher.
A pallet weighs 2,000 lb on 16 ft². What is the load per square foot?
Show answer
2,000 ÷ 16 = 125 lb per ft².
Lesson quiz · 5 questions
Score 60% or more to complete this lesson.
Create a free account to save your progress, take quizzes and earn a certificate.