ROOF-110 · Lesson 6 of 12 · 22 min

Fall protection on low-slope roofs

▶ Video coming soon A video version of this lesson is on the way.

Falls are the leading cause of death in construction, and roofers fall more than almost any other trade. Many of those falls happen from low-slope roofs, which surprises new workers. A low-slope roof feels safe. You can walk around on it like a floor, set down tools and materials, and forget that the edge is there. Then you step back to roll out a sheet, or turn around carrying insulation boards in the wind, or walk backwards pulling a hose, and the edge is not where you thought it was. Skylights and openings are the other big killer on low-slope roofs. A plastic skylight dome looks solid but can break under a worker's weight, and an opening covered by a loose sheet of plywood is a trap.

"On a flat roof the edge sneaks up on you," Dana told Rory on his first day at Ashgrove Plaza. "So we decide where the edge is going to stop you before anyone goes up, and then we build that."

This lesson covers how roofers are protected from falls on low-slope roofs: the rules, the systems and how to set them up. Lesson 7 covers steep roofs and the personal fall arrest equipment used on both.

When fall protection is required

Under OSHA's construction fall protection standard (29 CFR 1926 Subpart M), each employee on a walking or working surface with an unprotected side or edge 6 feet or more above a lower level must be protected from falling. Roofing work on low-slope roofs is covered by section 1926.501(b)(10). Holes, including skylights, are covered by 1926.501(b)(4), and the rules apply at 6 feet regardless of how short the task is. Where a worker could fall into dangerous equipment, protection is required at any height.

OSHA gives roofers on low-slope roofs a set of choices. Under 1926.501(b)(10), each employee engaged in roofing activities on a low-slope roof with unprotected sides and edges 6 feet or more above lower levels must be protected by a guardrail system, a safety net system, a personal fall arrest system, or a combination of a warning line system with a guardrail system, safety net system, personal fall arrest system or safety monitoring system. On roofs 50 feet or less in width, a safety monitoring system alone is allowed. Workers exposed to fall hazards must be trained by a competent person to recognize the hazards and use the systems (29 CFR 1926.503), and the employer must certify the training in writing.

Fall protection methods on low-slope roofs.
MethodHow it protectsTypical use on low-slope roofs
Guardraila physical barrier at the edge stops anyone reaching itperimeter of a roof, hoist landings, around openings
Flagged warning linea line on stanchions set back from the edge marks where work stopsthe work area away from edges
Travel restrainta harness and lanyard attached to an anchor are too short to let the worker reach the edgework between the barrier and the edge
Fall arresta harness, connector and anchor stop a fall after it beginsedge work where restraint is not practicable
Safety neta net catches a falling workerrare in roofing; used below some large openings
Covers and guardrails for holesa secured, marked cover or a guardrail stops a fall throughskylights, roof hatches, deck openings
Safety monitora competent person watches workers and warns them of the edgewith a warning line, or alone on roofs 50 ft wide or less

Guardrails

A guardrail is the best protection because it works without anyone having to do anything right. OSHA's guardrail criteria (29 CFR 1926.502(b)) require the top rail to be 42 inches, plus or minus 3 inches, above the walking surface, with midrails or equivalent about halfway up, and the top rail must withstand a force of at least 200 pounds applied in any outward or downward direction. On roofs, guardrails are usually built from steel posts in weighted bases (non-penetrating guardrails), clamped to parapets, or fastened to the structure. A parapet can act as a guardrail only if it meets the same height and strength criteria; most parapets on older plazas are far too low.

Guardrails are always used at hoist landings and material loading points, where workers lean out and handle loads at the edge. They are also the preferred protection around large openings and along any edge where work goes on for a long time. When a section of guardrail must be removed to land materials, the opening is protected another way while it is open, and the guardrail is replaced as soon as the load is in.

Barriers set back from the edge

A plan view of a low-slope roof with no parapet. A dashed warning line at least 6 feet from the edge, 34 to 39 inches high and flagged every 6 feet, surrounds the roofing work area. Near a block of mechanical equipment, the line is 10 feet back for travel perpendicular to the edge. A safety monitor stands on the same roof, in sight and within voice range of a worker between the line and the edge. Notes read: 6 feet or more requires fall protection; low-slope roofs allow guardrail, net, PFAS, or a warning line plus one of those or a safety monitor; a monitor alone is allowed on roofs 50 feet wide or less.
Fall protection layout on a low-slope roof.

A warning line system is a rope, wire or chain on stanchions that marks off the area where roofing work may be done without guardrails, nets or personal fall arrest. OSHA's criteria (29 CFR 1926.502(f)) include the following. The line is erected around all sides of the roof work area. It is set at least 6 feet back from the roof edge. Where mechanical equipment (such as a roof cutter or a powered material cart) is being used, the line must be at least 6 feet from the edge measured parallel to the direction of the equipment's travel and at least 10 feet from the edge measured perpendicular to it. The line is flagged with high-visibility material at intervals of not more than 6 feet, and its lowest point, including sag, is between 34 and 39 inches above the roof. The stanchions must resist tipping when pushed sideways near the top, and the line must have a minimum strength. Access paths through the line are protected and closed off when not in use. A warning line is a boundary, not a guardrail: it marks where people must stop, but it will not stop someone who walks into it.

On Ashgrove Plaza, Dana set the warning line 6 feet in from the open rear and side edges and 10 feet back along the side where the power tear-off machine traveled toward the edge. Because the front edge faced a busy sidewalk and parking lot, she clamped guardrail posts to the 12-inch front parapet instead of relying on a line. The hoist landing at the rear had a full guardrail on both sides. Work inside the warning line needed no harnesses, which let the crew roll membrane and move materials freely. For the narrow strip along the edges, workers used travel restraint lines attached to anchors in the field of the roof, and a safety monitor watched during short tasks there.

Worked problem

Setting out a barrier around a work area

A rectangular section of Ashgrove Plaza's roof measures 130 ft by 80 ft with open edges on all four sides. The warning line will be 6 ft in from three edges and 10 ft in from one long edge where the tear-off machine travels toward it. Stanchions go no more than 10 ft apart (Ridgecap's rule). How much line is needed and how many stanchions? Can a safety monitor alone protect workers on this roof?

Show solution
  1. Inside length: 130 − 6 − 6 = 118 ft (the 10 ft setback is on a long edge, so the length is unchanged).
  2. Inside width: 80 − 6 − 10 = 64 ft.
  3. Perimeter: 2 × (118 + 64) = 364 ft of line, plus extra for ties.
  4. Stanchions: 364 ÷ 10 = 36.4, so 37 spaces and 37 stanchions around a closed loop.
  5. Roof width: 80 ft is more than 50 ft.

Answer: About 364 ft of line on 37 stanchions. The roof is wider than 50 ft, so a safety monitor alone is not allowed; workers between the line and the edge need guardrail, net or PFAS protection, or a safety monitor working together with the warning line.

Safety monitoring

A safety monitoring system uses a competent person to watch roofers and warn them when they are unaware of a fall hazard or are acting unsafely. OSHA's criteria (29 CFR 1926.502(h)) require the monitor to be competent to recognize fall hazards, on the same walking surface as the workers, within visual sighting distance and close enough to communicate orally, and free of other duties that could take their attention away. Mechanical equipment may not be used or stored in areas protected only by safety monitoring. Safety monitoring is the weakest option because it depends on one person seeing every hazard and being heard in time. Ridgecap uses it only for short tasks in the strip between the warning line and the edge, never as the only protection on its larger roofs.

Personal systems on low-slope roofs

Travel restraint is the preferred personal system on low-slope roofs. The worker wears a full-body harness connected by a lanyard or line to an anchor, and the length is set so the worker cannot reach the edge. Because the worker never goes over the edge, there is no fall to arrest. The anchor can be a permanent roof anchor, a temporary anchor fastened through to the structure, or a weighted, non-penetrating mobile anchor designed for that roof surface and slope. The length of line must be measured: the distance from the anchor to the edge, minus a margin, decides the maximum lanyard length.

Fall arrest is used when the worker must be able to reach the edge, for example to install edge metal or flash the outside face of a parapet. A fall arrest system must stop the fall before the worker hits the ground or a lower level, so clearance below the edge matters, as you will see in lesson 7. On low-slope roofs there is another hazard: a lanyard running over the roof edge can be cut by a sharp metal edge or drip edge during a fall. Use lanyards and self-retracting lifelines rated for leading-edge use where the line may run over an edge.

Whatever personal system is used, the anchor must be strong enough. A pipe, a vent stack, a rooftop unit, a gas line or a skylight frame is not an anchor. Anchors are installed and inspected as their manufacturers and engineers specify.

Skylights and roof openings

Skylights are among the most dangerous features on a low-slope roof. Plastic domes and older wired glass can break under a worker who sits, steps or falls onto them, and they are often painted over or covered with dirt so that they blend into the roof. Many roofers have died falling through skylights while backing up or resting.

OSHA requires each employee on a walking or working surface to be protected from falling through holes, including skylights, more than 6 feet above lower levels, by personal fall arrest systems, covers or guardrail systems (29 CFR 1926.501(b)(4)). Covers must support at least twice the weight of employees, equipment and materials that may be on them, be secured to prevent displacement, and be marked with the word "HOLE" or "COVER" (29 CFR 1926.502(i)). Openings made during tear-off, such as where an old roof hatch or curb is removed, must be covered or guarded right away.

Dana's crew walks every roof before work starts and marks every skylight and opening on the site plan. Each one is protected before tear-off begins. "Never sit on a skylight, never stand on one and never step backwards on a roof you haven't walked," she told Rory.

Access, hatches and roof edges at the access point

Workers often reach low-slope roofs by ladder, stair tower, roof hatch or hoist landing, and the access point is often at the edge. Make sure the protection at the access point is in place before the first person steps off the ladder: a guardrail or a gate at the ladder landing, a protected path through the barrier to the work area, and a closed hatch or guardrail around an open hatch. A roof hatch left open with no guardrail is an opening someone can fall through.

Planning the fall protection for a low-slope job

Before work starts on a low-slope roof, the foreperson works through these questions and records the answers in the fall protection plan or site hazard assessment:

  • How high is the roof, and does any edge or opening require protection?
  • Where are the edges, parapets (and their heights), skylights, hatches and other openings?
  • Where will workers access the roof, and where will materials come up and debris come down?
  • Where can guardrails be used, and where will barriers or warning lines go?
  • What work must be done near the edge, and what personal system will protect it?
  • What anchors are available or will be installed, and are they rated for the system?
  • How will a worker who falls and is caught by a fall arrest system be rescued?
  • Who has the required training, and who will check the systems each day?

OSHA requires a written fall protection plan only in specific cases where conventional systems are infeasible, but Ridgecap writes a plan for every job anyway.

Common mistakes

  • MistakeTreating a barrier line as a guardrail.

    InsteadA barrier or warning line marks a boundary but will not stop a fall; anyone outside it needs other protection.

  • MistakeTying off to a vent pipe or rooftop unit.

    InsteadUse only anchors rated and installed for fall protection.

  • MistakeStepping backwards while rolling out membrane.

    InsteadKnow where you are relative to the edge and openings, and set up barriers so the edge cannot sneak up on you.

  • MistakeLeaving a skylight unprotected because the work is not right beside it.

    InsteadProtect skylights and openings before work starts anywhere nearby.

  • MistakeUsing a safety monitor alone on a roof wider than 50 feet.

    InsteadA monitor alone is allowed only on roofs 50 feet or less in width; otherwise combine it with a warning line, or use guardrail, net or PFAS.

Summary and key terms

  • OSHA requires fall protection at 6 feet on low-slope roofs under 1926.501(b)(10).
  • A warning line at least 6 feet from the edge (10 feet perpendicular to equipment travel), 34 to 39 inches high, marks the roofing work area.
  • A safety monitor must be competent, on the same roof, in sight, within voice range and free of other duties; alone, it is allowed only on roofs 50 feet wide or less.
  • Travel restraint keeps workers from reaching the edge and is preferred over fall arrest.
  • Skylights and openings must be guarded or covered with secured, rated covers.
  • Workers exposed to falls must be trained by a competent person, and the training certified in writing.
Guardrail system
A barrier of top rail, midrail and posts (and toeboard where needed) that stops workers reaching an edge.
Flagged warning line
A line on stanchions set back from a roof edge to mark the roofing work area.
Safety monitoring system
A competent person who watches roofers and warns them of fall hazards.
Travel restraint
A personal system that keeps a worker from reaching a fall hazard.
Personal fall arrest system (PFAS)
An anchor, connector and full-body harness that stop a worker after a fall has begun.
Skylight
A window in a roof; many are not strong enough to hold a falling worker.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. At what height does OSHA require fall protection on a low-slope roof?

    Show answer

    6 feet or more above a lower level.

  2. How far from the edge must a warning line be when mechanical equipment travels toward that edge?

    Show answer

    At least 10 feet, measured perpendicular to the direction of travel.

  3. What is the height range for a warning line?

    Show answer

    34 to 39 inches at its lowest point, including sag.

  4. When may a safety monitor be used alone?

    Show answer

    On low-slope roofs 50 feet or less in width.

  5. How must a skylight cover be marked?

    Show answer

    With the word HOLE or COVER, and it must be secured and support twice the expected load.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz