ROOF-340 · Lesson 10 of 12 · 57 min

Calculation practice

▶ Video coming soon A video version of this lesson is on the way.

On the Sunday practice test, Luca lost more marks on calculations than on anything else, and not because he could not do them. He had answered two take-off questions with plan area instead of roof area, forgotten to add the first fastener in a row, and rounded a number of bundles down instead of up. "Every one of those, you'd catch on the job," Dana said, "because the truck would be short. On the exam there's no truck. There's just an answer that's one of the four, because the person who wrote it knew exactly what mistake you'd make."

This lesson is a workbook. It gathers the calculations a roofer is expected to do into one formula sheet, then works through a set of exam-style problems from the whole program, each with the common trap that the wrong answers are built on. Work each one before reading the steps.

The formula sheet

The roofer's formula sheet.
CalculationFormulaWatch for
Slope as a ratiorise ÷ run; 1 in 50 = 20 mm per metreMixing rise in 12 and ratios
Pitch factor√(rise² + 144) ÷ 12, rise in inches per 12Using plan area for a sloped roof
Hip or valley factor√(rise² + 288) ÷ 12Measuring hips with the common rafter factor
Roof areaplan area × pitch factorLeaving out overhangs
Squaresroof area ÷ 9.29 m²Forgetting waste; rounding down
Coursesslope length ÷ exposure, rounded upUsing the shingle's full height
Net roll coverage(width − side lap) × (length − end lap)Using gross roll area
Fasteners in a rowlength ÷ spacing + 1Missing the first fastener
Thermal movementΔL = α × L × ΔTMixing units of α and L
Heat lossarea × ΔT ÷ total resistanceAdding U-values instead of resistances
Fall clearancelanyard + deployment + stretch + body + marginMeasuring from the roof instead of the anchor
Ladder baseheight ÷ 4Using the ladder length instead of the height
Weightarea × load per unit areaMixing kilograms and tonnes, or pounds and tons
In 100part ÷ whole × 100Dividing by the wrong whole

Always estimate the answer before calculating. If a roof is about the size of a large house and the answer comes out at 300 squares, something is wrong. On a multiple-choice exam, a quick estimate often rules out two options before any arithmetic is done.

Slopes and areas

Worked problem

1. Converting a slope

A roof slope is 5 in 12. Express it as a ratio, a number in 100 and an angle.

Show solution
  1. Ratio = 12 ÷ 5 = 2.4, so 1 in 2.4.
  2. In 100 = 5 ÷ 12 × 100 = 41.7.
  3. Angle = arctan(5 ÷ 12) = 22.6°.

Answer: 1 in 2.4, 41.7 in 100, 22.6°. Trap: writing 1 in 5 or 5 in 100.

Worked problem

2. Roof area, squares and bundles

A gable house measures 10.4 × 8.6 m on plan, including overhangs, with a 7 in 12 roof. How many squares of shingles are needed with 10 in 100 waste, and how many bundles at three bundles to the square?

Show solution
  1. Plan area = 10.4 × 8.6 = 89.44 m².
  2. Pitch factor = √(49 + 144) ÷ 12 = √193 ÷ 12 = 1.158.
  3. Roof area = 89.44 × 1.158 = 103.6 m².
  4. Squares = 103.6 ÷ 9.29 = 11.15.
  5. With waste = 11.15 × 1.10 = 12.26 squares.
  6. Bundles = 12.26 × 3 = 36.8, so 37 bundles.

Answer: About 12-1/4 squares, 37 bundles. Traps: using plan area (about 10 squares) or rounding the bundles down.

Worked problem

3. Hip length

A hip roof at 6 in 12 is 9.6 m wide at the wall line. How long is each hip from the wall line to the ridge?

Show solution
  1. Run = 9.6 ÷ 2 = 4.8 m.
  2. Hip factor = √(36 + 288) ÷ 12 = 18 ÷ 12 = 1.5.
  3. Hip = 4.8 × 1.5 = 7.2 m.

Answer: 7.2 m. Trap: using the common rafter factor, 1.118, which gives 5.4 m.

Worked problem

4. Courses

A slope is 6.10 m from eave to ridge. Shingles have a 143 mm exposure. How many courses?

Show solution
  1. 6,100 ÷ 143 = 42.66.
  2. Round up: 43 courses.

Answer: 43 courses. Trap: dividing by the shingle's full height instead of the exposure.

Low-slope quantities

Worked problem

5. Rise of a taper

A tapered system slopes at 1 in 50 over a 12 m run. What is the rise?

Show solution
  1. Rise = 12,000 ÷ 50 = 240 mm.

Answer: 240 mm. Trap: multiplying by 50, or giving 24 mm.

Worked problem

6. Insulation fasteners

Using the sample pattern from lesson 7 (8, 12 and 16 fasteners per 2.88 m² board), how many fasteners are needed for 600 m² of field, 150 m² of perimeter and 30 m² of corner?

Show solution
  1. Field = 600 ÷ 2.88 × 8 = 1,666.7.
  2. Perimeter = 150 ÷ 2.88 × 12 = 625.0.
  3. Corner = 30 ÷ 2.88 × 16 = 166.7.
  4. Total = 2,458.4, so 2,459.

Answer: Trap: using the field pattern for the whole roof, which undercounts.

Worked problem

7. Seam fasteners

A 30 m seam has fasteners every 300 mm. How many?

Show solution
  1. 30 ÷ 0.3 = 100 spaces.
  2. 100 + 1 = 101 fasteners.

Answer: 101. Trap: 100.

Worked problem

8. Adhesive

Contact adhesive covers 1.47 m² per litre. How many 18.9 L pails for 400 m²?

Show solution
  1. 400 ÷ 1.47 = 272.1 L.
  2. 272.1 ÷ 18.9 = 14.4, so 15 pails.

Answer: 15 pails. Trap: rounding to 14.

Worked problem

9. Ballast weight

A roof of 1,200 m² is ballasted with stone at 49 kg/m². What is the total weight in tonnes?

Show solution
  1. 1,200 × 49 = 58,800 kg.
  2. 58,800 ÷ 1,000 = 58.8 t.

Answer: 58.8 t. Trap: giving 588 t or 5.88 t by moving the decimal.

Worked problem

10. Asphalt for moppings

A 650 m² four-ply built-up roof has three interply moppings at 1.2 kg/m² and a flood coat at 2.9 kg/m². How much asphalt?

Show solution
  1. 650 × 1.2 × 3 = 2,340 kg.
  2. 650 × 2.9 = 1,885 kg.
  3. Total = 4,225 kg.

Answer: Trap: counting four interply moppings for four plies; with the first ply mopped to the board counted separately, there are three between plies.

Movement, heat and safety

Worked problem

11. Thermal movement

A 3.0 m aluminium coping sees a 90 °C range. α = 23 × 10⁻⁶ per °C. How much does it move?

Show solution
  1. ΔL = 23 × 10⁻⁶ × 3,000 × 90 = 6.21 mm.

Answer: About 6.2 mm. Trap: using 3 m instead of 3,000 mm and getting 0.006.

Worked problem

12. Heat loss

A 760 m² roof has a total RSI of 4.30. How much heat does it lose with 20 °C inside and −20 °C outside?

Show solution
  1. U = 1 ÷ 4.30 = 0.233.
  2. Heat loss = 0.233 × 760 × 40 = 7,070 W.

Answer: About 7.1 kW. Trap: using a temperature difference of 0 by adding 20 and −20.

Worked problem

13. Fall clearance

Lanyard 1.8 m, absorber 1.2 m, stretch 0.3 m, D-ring to feet 1.5 m, margin 0.9 m. The lower level is 5.4 m below the anchor. Is it safe?

Show solution
  1. Required = 5.7 m.
  2. Available = 5.4 m.

Answer: No. Trap: leaving out the safety margin and saying yes.

Worked problem

14. Labour days

A crew tears off and re-roofs about 160 m² a day. How many working days for 2,000 m², and how many crew hours for a crew of eight on 8-hour days?

Show solution
  1. Days = 2,000 ÷ 160 = 12.5, so 13 days.
  2. Crew hours = 13 × 8 × 8 = 832.

Answer: 13 days and 832 crew hours. Production rates are samples; real ones come from a company's own job records.

A right triangle for a 7 in 12 roof with run 12, rise 7 and slope length 13.89, giving a pitch factor of 1.158, and a second triangle for the hip with run 16.97 (12 × √2), rise 7 and length 18.36, giving a hip factor of 1.530 per unit of common run. A small table lists pitch factors for 4, 6, 8 and 12 in 12.
Pitch and hip factors come from right triangles.

Units

Many calculation errors are unit errors. On a Canadian roof, the job may mix metric with imperial habits: slopes in 12, boards in inches, rolls in squares. Convert everything to one system before calculating, and write the units at every step so that a wrong one shows up.

Useful conversions.
ConversionValue
1 square100 ft² = 9.29 m²
1 in25.4 mm
1 ft0.3048 m
1 m²10.76 ft²
RSI to R× 5.678
1 kg2.205 lb
1 US gallon3.785 L
Water1 kg per litre

More practice problems

Worked problem

15. Eave protection courses

Overhangs are 600 mm, the wall is 140 mm thick, the slope is 4 in 12, and eave protection must reach 300 mm past the inner face of the wall. How far up the slope must it go, and how many 914 mm wide courses are needed with 100 mm laps?

Show solution
  1. Horizontal distance = 600 + 140 + 300 = 1,040 mm.
  2. Up the slope = 1,040 × 1.054 = 1,096 mm.
  3. First course covers 914 mm; the second adds 914 − 100 = 814 mm, for 1,728 mm.
  4. Two courses are needed.

Answer: Two courses. Trap: measuring horizontally and forgetting the pitch factor, or measuring from the outside face of the wall.

Worked problem

16. Ponding load

A pond 5.0 × 3.0 m averages 30 mm deep. What does it weigh, and what is the load per square metre?

Show solution
  1. Volume = 5.0 × 3.0 × 0.030 = 0.45 m³ = 450 L.
  2. Weight = 450 kg.
  3. Load = 450 ÷ 15 = 30 kg/m².

Answer: 450 kg, or 30 kg/m². Trap: using 30 instead of 0.030 m for the depth.

Worked problem

17. Net coverage and rolls

A 1.0 × 8.0 m cap roll has 75 mm side laps and 150 mm end laps. How many rolls for 760 m² of field, with 5 in 100 waste?

Show solution
  1. Net coverage = 0.925 × 7.85 = 7.26 m².
  2. With waste = 760 × 1.05 = 798 m².
  3. Rolls = 798 ÷ 7.26 = 109.9, so 110 rolls.

Answer: 110 rolls, which matches the Carrick Street order. Trap: using gross coverage of 8.0 m² and ordering 100.

Worked problem

18. Cost per year of service

A restoration costs 46,000 dollars and is expected to add 12 years. A replacement costs 210,000 dollars and is expected to last 25 years. Which costs less per year of service? (Sample prices.)

Show solution
  1. Restoration = 46,000 ÷ 12 = 3,833 dollars a year.
  2. Replacement = 210,000 ÷ 25 = 8,400 dollars a year.

Answer: The restoration, in this example, if the roof is a good candidate for it. Trap: comparing first costs only.

Worked problem

19. Shares in 100

Of 125 exam questions, 38 are on low-slope roofing. What share is that in 100? A candidate answers 30 of them correctly. What is that in 100?

Show solution
  1. 38 ÷ 125 × 100 = 30.4.
  2. 30 ÷ 38 × 100 = 78.9.

Answer: About 30 in 100 of the exam, and about 79 in 100 of those questions. Trap: dividing 30 by 125 instead of by 38.

Worked problem

20. Ventilation

An attic floor is 96 m². At 1 in 300, how much net free vent area is needed, and how much of it goes at the ridge if it is split evenly?

Show solution
  1. Total = 96 ÷ 300 = 0.32 m² = 320,000 mm².
  2. Ridge = 320,000 ÷ 2 = 160,000 mm².

Answer: 0.32 m² in all, 160,000 mm² at the ridge. Trap: forgetting to convert square metres to square millimetres before dividing by the vent's rating per metre.

Worked problem

21. Noise

A grinder measures 94 dBA. Under an 85 dBA limit with a 3 dB exchange rate, how long may it be used in a day without hearing protection?

Show solution
  1. Increase = 94 − 85 = 9 dB, which is 3 halvings.
  2. Time = 8 ÷ 2³ = 1 hour.

Answer: One hour. Trap: halving once for each decibel, or using the wrong exchange rate.

Calculation questions on a long exam are where time disappears. Do the quick ones in the first pass and flag any that need more than three or four steps. When you come back, write each step on scrap paper with its units, check the answer against your estimate, and then look for it among the options. If your answer is not among them, the most common reasons are a unit error, a missing pitch factor, a missing plus one, or rounding in the wrong direction; check those four before starting again.

Common mistakes

  • MistakeUsing plan area for sloped roofs.

    InsteadMultiply by the pitch factor.

  • MistakeRounding material quantities down.

    InsteadRound up to whole units you can buy.

  • MistakeForgetting the first fastener in a row.

    InsteadFasteners = spaces + 1.

  • MistakeMixing millimetres and metres, or inches and feet, in one formula.

    InsteadConvert first and write units at each step.

  • MistakeCalculating without an estimate.

    InsteadEstimate first; it rules out wrong answers fast.

Summary and key terms

  • Keep a one-page formula sheet and practise every formula on it.
  • Areas: plan × pitch factor; hips and valleys: run × hip factor; squares with waste, rounded up.
  • Quantities: net coverage after laps, fasteners = spaces + 1, adhesive and asphalt by rate × area.
  • Movement, heat and safety: ΔL = αLΔT; heat loss = area × ΔT ÷ R; clearance adds every part from the anchor.
  • Estimate first, write units at every step, and know the trap each wrong answer is built on.
Formula sheet
A personal one-page list of the formulas and conversions needed for the exam.
Net coverage
The area a roll or board actually covers after laps.
Production rate
The amount of work a crew completes per day or hour, from job records.
Hip factor
The multiplier for the length of a hip or valley per unit of common run.
Unit error
A mistake caused by mixing units within a calculation.
Estimate
A quick rough answer used to check a calculation.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. A 4 in 12 roof has 140 m² of plan area. How many squares with 15 in 100 waste?

    Show answer

    140 × 1.054 × 1.15 = 169.7 m²; ÷ 9.29 = 18.3 squares.

  2. A 1.0 × 8.0 m roll has 100 mm side laps and 150 mm end laps. Net coverage?

    Show answer

    0.9 × 7.85 = 7.07 m².

  3. A 9 m steel panel sees 70 °C. α = 11.7 × 10⁻⁶. Movement?

    Show answer

    7.4 mm.

  4. A 60 m seam with fasteners at 150 mm. How many?

    Show answer

    400 + 1 = 401.

  5. A ladder rests 5.6 m up a wall. Where is its base?

    Show answer

    1.4 m out.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz