INS-340 · Lesson 8 of 12 · 20 min

Cover materials and high-temperature fabrics

▶ Video coming soon A video version of this lesson is on the way.

When Tessa Moreau visited Pellam Thermal Covers with Tomasz Nowicki in June 2026, the first thing Ferris Quade showed her was not a sewing machine but a rack of rolls: grey, white, tan and dark blue fabrics, needled mats in several thicknesses, rolls of stainless steel wire mesh and boxes of thread and hardware. "Pick the wrong one of these and the cover falls apart in a year," he said. "Pick the right ones and it outlasts the valve." This lesson covers the layers of a removable cover, the fabrics, mats and barrier materials used in each, their typical temperature limits, and how to choose them for hot, outdoor, food plant, chemical and acoustic service.

The layers of a cover

A flexible removable cover is built like a quilt, usually with three layers:

  • Inner jacket (hot face). The fabric against the hot surface. It must survive the full operating temperature, and the highest temperature the item can reach, without breaking down.
  • Insulation mat. The filling that does the thermal work, sewn or pinned between the jackets so it cannot slide.
  • Outer jacket (cold face). The fabric outside, which must resist the environment: weather, sunlight, water, oil, chemicals, washdown, abrasion and handling.

Acoustic covers add a barrier layer, and cold covers a vapour retarder, each placed where its own temperature limit and function require. Covers for very hot or abrasive service often add a stainless steel wire mesh liner on the hot face, which holds the mat in place and resists heat and wear.

A cross-section through a removable cover against a hot valve surface, showing from the hot side outward: stainless steel mesh liner, inner fabric, a thick insulation mat, a thin barrier layer partway out, a thinner second mat layer, and the outer fabric. A temperature line drops steeply through the mat from the hot surface to near room temperature at the outer fabric, with the barrier position marked.
The layers of a cover. Temperature falls through the mat, so a heat-sensitive barrier goes toward the cool side.

Fabrics

Most cover fabrics are woven glass fibre, which does not burn and keeps its strength to high temperatures, with or without a coating. The coating sets how the fabric resists water, chemicals and wear, and usually limits the temperature of that face. Typical continuous limits, which vary by product, are:

Typical cover fabrics and their temperature limits; always check the maker's data.
Fabric (typical)Typical limitTypical use
Silicone-coated glass fabric260 °C (500 °F)Outer jacket for general industrial and outdoor use; flexible, water-resistant, takes stitching well
PTFE-coated glass fabric260 °C (500 °F)Outer jacket where chemicals, oils, UV or washdown are present; slick surface sheds dirt
Uncoated or texturized glass cloth540 °C (1,000 °F)Inner jacket on hot surfaces; not water-resistant
Vermiculite-coated glass fabricabout 800 °C (1,500 °F)Inner jacket and heat shields at higher temperatures
High-silica clothabout 980 °C (1,800 °F)Inner jacket on very hot items such as turbine casings and exhaust
Stainless steel knitted wire meshabove 540 °C (1,000 °F) (by alloy)Hot-face liner to hold mat and resist abrasion
Vinyl-coated polyester or similarabout 100 °C (210 °F)Indoor commercial covers on warm water and low-temperature lines only

The outer fabric runs much cooler than the hot face, because the mat drops the temperature, so a silicone or PTFE outer jacket is fine on a cover for a steam valve at 186 °C (366 °F), and often on much hotter items. The inner jacket faces the full temperature, so on Kellerton's steam the inner fabric is uncoated glass cloth, and the stainless mesh liner is added only on items that get handled roughly or exceed the cloth's limit.

Colour matters too. Many fabricators offer several colours, and plants use them to tell services apart, or to make dirt and contamination visible in food areas. Kellerton specifies a light grey outer jacket in the boiler house and a white PTFE outer jacket in processing areas.

Insulation mats

Typical insulation mats for covers.
Mat (typical)Typical limitNotes
Glass fibre needled mat540 °C (1,000 °F)The most common filling; no binder, so no smoke or odour at first heat-up
Mineral wool blanketabout 650 °C (1,200 °F)Higher temperature than glass; some products have binders that burn off
High-silica needled matabout 980 °C (1,800 °F)For very hot service
Alkaline earth silicate (AES) or refractory ceramic fibre (RCF) blanket1,100 °C (2,000 °F) and higherFor extreme temperatures; RCF needs the controls INS-230 described, and many users prefer AES
Aerogel blanketabout 650 °C (1,200 °F) for high-temperature gradesThin covers where space is tight; dusty to cut; check the maker's handling rules

Mat thickness is set by the heat loss and surface temperature required, as INS-410 will calculate in detail; 25 to 50 mm (1 to 2 in) is common on steam fittings, often in two layers so that the seams do not line up. Needled mats are made by punching the fibres together with barbed needles, which holds them without binder, so they do not give off smoke when first heated. Mats with organic binders can smoke and smell at first start-up, which in a food plant can trigger a complaint or an alarm.

Barriers and vapour retarders in covers

Acoustic covers need a barrier layer, which is usually mass-loaded vinyl or a similar loaded sheet with a limited temperature range, or for hot service a high-temperature loaded fabric or a heavy mat. Because the barrier must stay within its limit, its position in the cover is a design decision, worked out from the temperature drop through the mat.

Worked problem

Where does the barrier go?

An acoustic cover for a valve at 180 °C (356 °F) has 50 mm (2 in) of mat in total, with a barrier layer whose limit is about 80 °C (175 °F). Taking the mat's thermal conductivity as 0.045 W/(m·K) (0.31 Btu·in/(h·ft²·°F)), the outside surface resistance as 0.1 m²·K/W (0.57 h·ft²·°F/Btu) and the room at 25 °C (77 °F), estimate the barrier temperature if it sits halfway through the mat, and if it sits with three quarters of the mat inside it.

Show solution
  1. Halfway (25 mm inside, 25 mm outside): mat resistances = 0.025 ÷ 0.045 = 0.556 m²·K/W each; total = 0.556 + 0.556 + 0.1 = 1.211.
  2. Heat flow = (180 − 25) ÷ 1.211 = 128 W/m².
  3. Barrier temperature = 180 − 128 × 0.556 = 108.9 °C: too hot.
  4. Three quarters inside (38 mm inside, 13 mm outside): resistances 0.844 and 0.289; total = 0.844 + 0.289 + 0.1 = 1.233; heat flow = 155 ÷ 1.233 = 125.7 W/m².
  5. Barrier temperature = 180 − 125.7 × 0.844 = 73.9 °C: within the limit.

Answer: With the barrier halfway, it would run at about 109 °C (228 °F) and soften; with three quarters of the mat inside it, about 74 °C (164 °F). The outer surface is about 38 °C (100 °F) either way. This simple flat-layer estimate ignores the curvature of the item, which a full calculation would include.

On Compressor No. 5 the discharge valves and flanges ran at about 80 °C (175 °F), so the barrier temperature was not a concern: Pellam built those covers with 25 mm (1 in) of glass fibre mat inside, then a layer of MLV, then a further 13 mm (½ in) of mat and the outer jacket, giving both decoupling and absorption on each side of the barrier.

Cold covers need a vapour retarder on the warm, outer side, with the overlaps and closures sealed. In practice this means closed-cell or sealed constructions, overlapping flaps with sealing strips, and careful fitting. Many designers avoid removable covers on lines colder than a few degrees below freezing, as lesson 6 noted.

Choosing materials for the service

ASTM C1695 groups hot-service blankets into three categories, which are a useful way to think about any cover:

  • Industrial. Plant service, with weather resistance, chemical resistance or both, up to about 538 °C (1,000 °F) under the standard.
  • Outdoor commercial. Outdoor service on commercial systems, needing weather resistance.
  • Indoor commercial. Indoor heating and plumbing systems, such as steam and hot water in buildings, needing neither weather nor chemical resistance, limited to about 260 °C (500 °F).

Beyond that, the conditions of each location point to particular choices:

Matching cover materials to the conditions.
ConditionTypical choices
OutdoorsSilicone- or PTFE-coated outer jacket; seams and flaps arranged to shed water; drain grommets at low points; UV-resistant thread
Washdown and food areasPTFE-coated outer jacket in a light colour; sealed, smooth seams; no loose fibres; stainless hardware; no hook-and-loop where it traps dirt
Oil and chemical exposurePTFE-coated outer jacket; closures that let leaks show and drain
Very hot surfacesHigh-silica or vermiculite-coated inner jacket, stainless mesh liner, high-temperature mat
Rough handling or abrasionHeavier outer fabric, stainless mesh liner, reinforcing patches at straps and lifting points
Acoustic serviceBarrier layer placed within its temperature limit, decoupled by mat on the inside; sealed overlaps

The specification usually names the categories and, sometimes, the exact fabrics. When it does not, the insulator gives the fabricator the conditions and lets the fabricator propose materials, then checks the proposal against the data sheets. For the PRV station covers, Pellam's proposal was silicone-coated glass outside in light grey, uncoated texturized glass cloth inside, 38 mm (1 ½ in) of needled glass fibre mat, glass fibre thread with a PTFE coating, and stainless steel hardware. Raj checked each data sheet against the 186 °C (366 °F) steam and approved it.

Materials to avoid

  • Organic fabrics such as cotton canvas and nylon on hot surfaces; they char and can burn.
  • Thread with a lower limit than the fabrics. A cover is only as hot-rated as its thread; lesson 9 covers thread.
  • Mats with binders in areas sensitive to smoke or odour, unless they are heated out first.
  • Galvanized or plated hardware on hot covers in some services, where the coating can flake or, on austenitic stainless steel at high temperature, cause problems; stainless hardware is the usual choice.
  • Chloride-bearing materials against austenitic stainless steel at the temperatures where stress corrosion cracking can occur, as INS-220 explained; inner jackets and mats for stainless items should be suitable for stainless steel.

A worked material selection

When Wendell sent Pellam the information for the Compressor No. 5 covers, he listed the conditions, and Ferris proposed the materials. The reasoning shows how the choices follow from the service:

The materials for the Compressor No. 5 acoustic covers.
ConditionChoiceReason
Surface about 80 °C (175 °F), ammonia engine room, indoorsUncoated glass cloth inner jacketAmple temperature margin; no coating needed against the surface
Acoustic covers on lagged lineMLV barrier between two layers of matDecouples the barrier from the valve and absorbs on both sides
Oil mist from the compressor package, washdown of the floor nearbySilicone-coated glass outer jacketResists oil and water and wipes clean
Ammonia atmosphereStainless steel hardware, no copper or brassAmmonia attacks copper alloys
Overlap onto lagging jacketEnd skirts with drawstrings and a barrier stripSeals the joint acoustically while staying removable

The ammonia point is easily missed. Copper and its alloys, including brass and bronze, corrode in ammonia, so brass grommets, snaps or buckles, which some fabricators use on light covers, would have gone green and failed in the engine room. Ferris used stainless steel throughout, as he does for all industrial covers.

Fire, smoke and food safety

In buildings and some plants, the outer materials of a cover may need to meet surface burning limits for flame spread and smoke, like other insulation materials in plenums and exposed spaces. Glass fabrics and mats are noncombustible or have low ratings, but some coatings and barrier layers add to the smoke rating. The fabricator's data sheets show the tested values, and the specification or the building code sets the limits.

In food plants, the plant's sanitation rules may add more: no loose fibres that could reach the product, materials that do not shed, colours that show dirt, and covers that can be wiped down with the plant's cleaning chemicals without breaking down. Kellerton's sanitation lead approves the outer fabric for any cover in a processing area before it is ordered; she is the same person who inspected the blancher tank jacket in INS-310.

Common mistakes

  • MistakeChoosing the outer fabric for the full process temperature and the inner for the environment.

    InsteadThe inner jacket faces the heat; the outer jacket faces the environment. Choose each for its own conditions.

  • MistakePutting a vinyl barrier against the hot face of an acoustic cover.

    InsteadPlace the barrier where the temperature through the mat keeps it within its limit.

  • MistakeUsing hook-and-loop and rough seams in a washdown area.

    InsteadUse smooth, sealed seams and cleanable, light-coloured PTFE jackets with stainless hardware.

  • MistakeUsing a mat with binder on a cover for a food area.

    InsteadUse needled mats without binder, or heat binder-bearing mats out before use.

  • MistakeApproving a fabricator's proposal without data sheets.

    InsteadCheck each fabric, mat, thread and hardware item against its data sheet and the service conditions.

Summary and key terms

  • A cover has an inner jacket for the heat, an insulation mat, and an outer jacket for the environment, with barriers, vapour retarders or mesh liners added as needed.
  • Glass fabrics with silicone or PTFE coatings are common outer jackets; uncoated, vermiculite-coated and high-silica cloths and stainless mesh face higher temperatures.
  • Needled glass fibre mat is the common filling; mineral wool, high-silica, AES and aerogel suit higher temperatures or thin covers.
  • A heat-sensitive barrier must sit where the temperature drop through the mat keeps it within its limit.
  • ASTM C1695 groups hot-service blankets into industrial, outdoor commercial and indoor commercial categories; local conditions decide the fabrics, seams and hardware.
Inner jacket
The fabric of a cover that faces the hot surface.
Outer jacket
The fabric of a cover that faces the surroundings.
Insulation mat
The filling of a cover that provides its thermal resistance.
Needled mat
A fibre mat held together by needle-punching, without binder.
PTFE-coated glass fabric
Woven glass fabric coated with polytetrafluoroethylene, resistant to chemicals and dirt.
Silicone-coated glass fabric
Woven glass fabric coated with silicone rubber, flexible and water-resistant.
High-silica cloth
A fabric of nearly pure silica fibre for very high temperatures.
Wire mesh liner
A knitted stainless steel layer on the hot face of a cover.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. Which layer of a cover must withstand the full surface temperature?

    Show answer

    The inner jacket (and any hot-face liner).

  2. Why are PTFE-coated outer jackets preferred in washdown areas?

    Show answer

    They resist water, chemicals and dirt and are easy to clean.

  3. What is an advantage of needled mat over mat with binder?

    Show answer

    It gives off no smoke or odour when first heated.

  4. A barrier has a limit of 80 °C (175 °F). The flat-layer estimate puts it at 109 °C (228 °F) halfway through the mat. What change helps?

    Show answer

    Move it further out, so more of the mat is inside it.

  5. What is the ASTM C1695 temperature limit for indoor commercial blankets?

    Show answer

    About 260 °C (500 °F).

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz