Foot and leg protection

Feet carry us through every working day, often over uneven ground, wet floors, sharp debris and around heavy loads and moving equipment. Foot injuries include crushed toes and feet from falling or rolling objects, punctures from nails and sharp scrap, cuts from chainsaws and other tools, burns from molten metal, hot surfaces and chemicals, electrical shock, and sprains, fractures and other injuries from slips, trips and falls. Many foot injuries are serious: a crushed foot can mean months off work and permanent disability. Protective footwear is required in many workplaces, and choosing the right footwear depends on understanding the hazards and the markings that show what a particular boot or shoe has been tested to resist. This lesson covers foot hazards, the Canadian and US footwear standards and markings, metatarsal protection, slip resistance, electrical properties, chainsaw and leg protection, fit and comfort, and inspection and care.

Foot hazards and controls

Common foot hazards include objects falling onto the feet, such as tools, parts, pipes and pallets; objects rolling onto the feet, such as carts, hand trucks and vehicles; compression between objects; sharp objects underfoot, such as nails, screws, glass and metal scrap; hot, molten or corrosive materials; electrical hazards from live conductors or static build-up; slippery, uneven or unstable walking surfaces; and cutting tools such as chainsaws and brush cutters. Controls before PPE include good housekeeping to remove debris, separating pedestrians from forklifts and vehicles, using carts and lifting aids instead of carrying heavy items, safe stacking and storage, anti-slip flooring and drainage, and machine guarding. Protective footwear protects against what remains.

Parts of protective footwear

Protective footwear combines several protective components with a comfortable, supportive boot or shoe:

• A toe cap of steel, aluminium or composite material such as fibreglass, carbon fibre or plastic, built into the toe to resist impact and compression.
• A puncture-resistant midsole plate of steel or flexible composite fabric that resists nails and other sharp objects penetrating the sole.
• A metatarsal guard, internal or external, that protects the upper part of the foot between the toes and the ankle.
• An outsole made of rubber or other compounds, with a tread pattern that provides grip and may resist heat, oil and chemicals.
• Electrical properties provided by the materials of the sole and construction, either insulating against shock or dissipating static electricity.
• The upper, made of leather, rubber or synthetic materials, which supports the foot and ankle and may resist water, chemicals, heat or cuts.

Composite toe caps and plates are lighter than steel, do not conduct heat or cold as readily, and do not set off metal detectors, which is useful in some workplaces. Steel caps are thinner for the same protection, so boots can be less bulky.

Footwear standards and markings

In Canada, protective footwear is certified to CSA Z195, Protective footwear (the current edition is Z195:14, reaffirmed in 2025), and CSA Z195.1, Guideline on selection, care, and use of protective footwear. Provincial and federal OHS regulations generally require CSA-certified footwear where there is a foot hazard. Rather than words, CSA Z195 uses a system of coloured symbols sewn or stamped on the outside of the footwear, usually on the tongue or side, so that the protection can be checked at a glance.

Not all footwear sold as work boots is protective footwear. Fashion boots with a reinforced toe, or work boots without certification marks, may not meet any standard. Workers and employers should look for the certification mark of an accredited body and the correct symbols or label, not just a description in a catalogue.

Metatarsal protection

The metatarsal bones form the top of the foot between the toes and the ankle. A toe cap does not protect them, so a heavy object dropped on the top of the foot can still cause serious fractures. Metatarsal guards are recommended or required where there is a risk of heavy objects striking the top of the foot, as in foundries, steel mills, heavy fabrication, rail and pipe handling, and demolition. Internal metatarsal guards are built into the boot and are less likely to snag, while external guards are strapped over the laces and can be added to existing boots, though they may catch on objects and be less comfortable.

Slip resistance

Slips, trips and falls on the same level cause a large share of workplace injuries. Footwear outsoles influence slip resistance through their compound, hardness, tread pattern and wear. Softer compounds tend to grip better on smooth surfaces, while deep, open tread patterns help on mud and snow but can trap debris. On oily or greasy floors, compounds and tread designs made for oil resistance and grip are needed. Some footwear is tested for slip resistance using standards such as ASTM F2913 or ISO 13287, which measure the coefficient of friction on test surfaces such as wet ceramic tile or steel with glycerine. In winter conditions, ice cleats or footwear with integrated studs can reduce slips outdoors but must be removed before walking on smooth indoor floors, where they can make slipping more likely. Worn treads should be a trigger for replacement.

Electrical properties of footwear

Footwear with electrical properties falls into two opposite categories, and confusing them can be dangerous:

• Electric shock resistant or electrical hazard footwear has insulating soles that provide a secondary source of protection against accidental contact with live electrical conductors at low voltages under dry conditions. It is not a primary protection; workers on energized equipment must still follow electrical safety procedures, and its protection is reduced by wet conditions, wear, cuts and embedded conductive objects such as metal shavings.
• Static dissipative footwear reduces the build-up of static electricity by conducting it from the body to the ground through the sole at a controlled rate, and conductive footwear provides a very low-resistance path to ground for work with explosives or sensitive electronics. Both allow current to pass, so they must never be used where workers may contact live electrical conductors.

Choosing between insulating and dissipative footwear depends on whether the main hazard is shock from live circuits or ignition and equipment damage from static discharge.

Chainsaw and leg protection

Chainsaw operators face a high risk of serious leg and foot injuries, because the saw's chain can contact the legs during kickback or if the saw slips. Chainsaw protective trousers, chaps and leggings contain layers of long, strong fibres that are pulled out by the chain and wrap around the drive sprocket, stopping the chain in a fraction of a second. Chainsaw-rated boots contain similar materials in the upper. These garments must be certified to a recognized standard, must cover the front of the legs from the waist to the top of the boots, and must be replaced if cut, because the protective fibres pulled out by a cut are no longer available. They do not make the operator invulnerable; proper technique, chain brake, chain catcher and training are essential. Other leg protection includes leggings and spats for foundry and welding work, which protect against molten metal and sparks entering the boots, knee pads for kneeling work, and shin guards for work with heavy materials.

In Canada, chainsaw protective leg wear and footwear are certified to standards such as CAN/BNQ 1923-450 and CSA Z195 (for footwear), and many provinces have specific requirements for forestry workers.

Selecting, fitting and breaking in footwear

Selecting protective footwear starts from the hazard assessment: which toe protection grade, puncture resistance, metatarsal protection, electrical properties, slip resistance, chemical resistance, heat resistance, waterproofing, insulation and ankle support the job requires. Fit matters as much as protection. Footwear should be tried on at the end of the day, when feet are slightly swollen, with the socks that will be worn at work. The toe cap should not press on the toes, and there should be about a thumb's width of space in front of the longest toe. The heel should be held firmly without slipping, and the widest part of the foot should match the widest part of the boot. Workers who stand or walk for long periods may benefit from cushioned insoles, though only insoles approved by the manufacturer should be used in electrical hazard or static dissipative footwear, because others can change the electrical properties. Breaking in new boots gradually reduces blisters and discomfort.

Inspection, care and replacement

Protective footwear should be inspected regularly for cracks or holes in the uppers, separation of the sole from the upper, exposed or dented toe caps, worn treads, cuts in the sole, embedded metal or stones, and loss of waterproofing. A toe cap that has taken a heavy impact or compression may be deformed even if no damage is visible from the outside, and the footwear should be replaced. Electrical hazard footwear loses insulating ability when the sole is worn, cut or wet, and static dissipative footwear can lose its properties when dirty or when non-approved insoles are used, so some workplaces test static dissipative footwear daily with a tester. Leather boots should be cleaned and treated to keep the leather supple, dried at room temperature rather than on heaters, and stored away from heat and chemicals. Footwear exposed to chemicals should be decontaminated or discarded as the safety data sheet and manufacturer advise.

Chemical, heat and cold hazards to the feet

Rubber and PVC boots protect against water, chemicals and wet concrete, and are available with toe caps and puncture-resistant soles. Boots for chemical work should be chosen from the manufacturer's resistance data, just like gloves, and trouser legs should be worn outside the boots so liquids run off rather than into them. Workers near molten metal need boots without laces or with quick-release fastenings, so they can be removed quickly if metal gets inside, together with spats or leggings. Insulated boots rated for low temperatures protect against cold and frostbite, while heat-resistant soles protect workers who stand on hot surfaces such as asphalt and furnace floors.

Socks, insoles and foot health

Foot comfort affects safety as well as wellbeing. Workers who stand or walk all day on hard floors are prone to sore feet, heel pain and back problems, and tired workers are more likely to slip or lose concentration. Moisture-wicking socks of wool or synthetic blends keep feet drier than cotton and reduce blisters and fungal infections. Rotating between two pairs of boots allows each pair to dry fully between shifts. Anti-fatigue mats at workstations reduce strain, and workers with foot conditions should seek advice from a health professional about orthotics, choosing protective footwear that accepts them without affecting certification.