PWR-310 · Lesson 12 of 12 · 34 min

Third class problem practice

▶ Video coming soon A video version of this lesson is on the way.

On the night of Monday, September 7, 2026, Labor Day, Okonkwo Demarest found an envelope in the study binder with his name on it. Inside was a practice paper Grazyna Wolanski had put together from the summer's work: twenty-five questions, a formula sheet left deliberately blank, and a note: "Ninety minutes. No phone. Bring it to me Wednesday." The plant was quiet after the long weekend, and Desmond Kirwan agreed to cover the rounds for an hour and a half after the 02:00 readings. In the morning a new trainee, Tamar Ellingsen, would start her first day shift; Okonkwo wanted the paper done before he went home.

This lesson pulls the course together the way an examination does. It describes the Third Class examinations and how candidates qualify for them, sets out a method for calculation questions that works under time pressure, lists the traps examiners build into the wrong answers, and works a set of mixed problems drawn from every lesson of the course.

The examinations

Ohio's stationary steam engineer license is issued by the Division of Industrial Compliance under its boiler law. The examination, given by PSI, is a closed-book paper of 50 multiple-choice questions in three hours, with a pass mark of 70 in 100 and a silent, non-programmable calculator allowed. The candidate bulletin's content outline in use in 2026 lists boiler design, construction, combustion, indicators and devices, operation, pumps, auxiliary equipment and environmental control, and adds topics the high pressure boiler operator examination does not have: steam turbine design, steam turbine associated equipment, and a block of seven math formula questions. The bulletin names Steam Plant Operation as the reference text; the book is not allowed in the testing center. Other states and cities with graded engineer licenses set their own examinations, so a candidate elsewhere checks the local authority's current bulletin.

The math formula block is where this course's material sits most directly, but turbine, combustion and boiler design questions also need it. PWR-320 (turbines), PWR-330 (boilers and combustion control) and PWR-340 (codes and materials) build on this course for the rest of the outline. ELEC-210 and lesson 11 cover the electrical side.

Qualifying

Ohio's rule gives several routes to the stationary steam engineer license: 2,000 hours on a steam boiler of more than 15 psi or on a steam turbine of more than 30 horsepower; 700 hours on such a turbine, or 1,000 hours on such a boiler, plus an approved 125-hour steam boiler and steam turbine course; a current high pressure boiler operator license plus 400 hours on such a turbine and the 125-hour course; or 2,000 hours on a turbine of more than 100 horsepower or one used for generating electricity. All experience must be verified in writing by a person licensed to operate the equipment. Okonkwo's boiler hours already met the first route, and he was taking the 125-hour course for its turbine content; his plan was to sit the examination in the spring of 2027.

A method for calculation questions

Under time pressure, a fixed routine is faster than inspiration. Grazyna's version, which she had written inside the cover of Okonkwo's binder, has seven steps:

  • Read the question twice. Underline what is asked, and note whether the answer is wanted per unit mass, per hour, in gauge or absolute pressure, or in a particular unit.
  • Sketch it. A box for the boiler, an arrow for each stream, a free-body diagram, a triangle. Most errors of sign and direction disappear on a sketch.
  • List the data with units, converting at once to consistent ones: absolute pressure and temperature, meters or feet, seconds or hours.
  • Name the principle: energy balance, equilibrium, continuity, gas law, Fourier, LMTD. Then write the formula in symbols before putting numbers in.
  • Estimate the size of the answer.
  • Calculate, keeping intermediate values in the calculator.
  • Check the units and the estimate, then find the answer among the options. If it is not there, look for the slip before guessing.

With 50 questions in 180 minutes, the license examination allows about 3.6 minutes per question, which is generous for recall questions and enough for most calculations. A sensible plan is a first pass answering everything quick, marking the long calculations; a second pass working them; and a few minutes at the end to check that every answer is marked, since an unanswered question scores nothing and a guess among four options scores one time in four.

The traps in the wrong answers

The wrong options in a calculation question are rarely random. They are the answers given by predictable slips, and knowing the list helps a candidate catch them:

Common slips that examiners build distractors around.
SlipWhere it appearsThe check
Gauge pressure used as absoluteGas laws, steam tables, compressor ratiosAdd atmospheric pressure before any gas law or table
Celsius or Fahrenheit used as absoluteGas laws, Carnot, radiation, entropyKelvin or Rankine wherever a temperature multiplies or divides
Diameter used for radiusAreas, torque, centripetal force, cylinder conductionWrite A = πD²/4 or πr², and check which symbol the formula uses
Revolutions per minute used as radians per secondCentripetal force, kinetic energy, power from torqueω = 2πN ÷ 60
Missing √3Three-phase power and currentLine values: P = √3 V I cos φ
Arithmetic mean for LMTDHeat exchangersUse (ΔT₁ − ΔT₂) ÷ ln(ΔT₁ ÷ ΔT₂)
Dryness ignoredWet steam enthalpy and volumeh = h_f + x h_fg
Difference of efficienciesEnergy savingsInput = output ÷ efficiency; subtract inputs
Energy units mixedWork and heat together1 Btu = 778 ft·lbf; 1 kWh = 3,412 Btu

Practice problems

The problems below are typical of Grazyna's paper. Work each before reading the solution.

Worked problem

Problem 1: required shell thickness

A cylindrical vessel of 48 in inside diameter is to hold 220 psig. Using the simple thin-cylinder relation with an allowable stress of 16,000 psi and a joint efficiency of 1.0, what wall thickness is needed, before any corrosion allowance?

Show solution
  1. Rearrange σ = pD ÷ 2t for t:
  2. \[t = \frac{pD}{2\sigma} = \frac{220 \times 48}{2 \times 16{,}000} = 0.33 \text{ in}\]

Answer: About 0.33 in. The code formula for a real vessel adds terms that make the result slightly larger, and a corrosion allowance; PWR-340 covers it.

Worked problem

Problem 2: general gas law

A gas at 60 psia and 86 °F occupies 18 ft³. It is compressed to 7 ft³ and its temperature rises to 194 °F. Find the final pressure.

Show solution
  1. \[p_2 = p_1 \frac{V_1}{V_2} \frac{T_2}{T_1} = 60 \times \frac{18}{7} \times \frac{653.67}{545.67} = 184.8 \text{ psia}\]

Answer: About 184.8 psia. The distractor built on Fahrenheit temperatures would give 348.0 psia.

Worked problem

Problem 3: steam generation and fuel

A boiler makes 20,000 lb/h of dry saturated steam at 164.7 psia (h_g = 1,196.0 Btu/lb) from feedwater at 221 °F (h_f = 189.2 Btu/lb). Its efficiency is 0.82 on natural gas with an HHV of 1,030 Btu/ft³. Find the heat added to the steam and the gas burned per hour.

Show solution
  1. Heat per pound and in total:
  2. \[q = 1{,}196.0 - 189.2 = 1{,}006.8 \text{ Btu/lb}, \qquad Q = 20{,}000 \times 1{,}006.8 = 20.1 \text{ million Btu/h}\]
  3. Fuel:
  4. \[\dot{V} = \frac{20{,}136{,}000}{0.82 \times 1{,}030} = 23{,}800 \text{ ft}^3\text{/h}\]

Answer: About 20.1 million Btu/h into the steam and 23,800 ft³/h of gas.

Worked problem

Problem 4: torque from power and speed

The backup feed pump turbine delivers 75 hp at 3,600 r/min. Find its output torque.

Show solution
  1. \[T = \frac{5{,}252 \times \text{hp}}{N} = \frac{5{,}252 \times 75}{3{,}600} = 109 \text{ lbf·ft}\]

Answer: About 109 lbf·ft. The constant 5,252 is 33,000 ÷ 2π, from 1 hp = 33,000 ft·lbf/min.

Worked problem

Problem 5: sizing an oil cooler

A lubricating oil cooler must remove 102,400 Btu/h, cooling oil from 140 to 113 °F with cooling water warming from 77 to 95 °F in counterflow. With U = 53 Btu/h·ft²·°F, what area is needed?

Show solution
  1. End differences: 140 − 95 = 45 °F and 113 − 77 = 36 °F.
  2. \[\Delta T_{lm} = \frac{45 - 36}{\ln(45/36)} = 40.3 \text{ °F}, \qquad A = \frac{102{,}400}{53 \times 40.3} = 47.9 \text{ ft}^2\]

Answer: About 48 ft². The arithmetic mean, 40.5 °F, gives almost the same answer here because the end differences are close; with very different end differences the error grows.

Worked problem

Problem 6: pump and motor power

A pump delivers 400 gpm of cold water against 200 ft of head. Pump efficiency is 0.72 and motor efficiency 0.93. Find the shaft power and the electrical input in kW.

Show solution
  1. \[P_s = \frac{400 \times 200}{3{,}960 \times 0.72} = 28.1 \text{ hp}, \qquad P_{in} = \frac{28.1 \times 0.746}{0.93} = 22.5 \text{ kW}\]

Answer: About 28.1 hp at the shaft and 22.5 kW from the supply.

Worked problem

Problem 7: air for propane

How much air is needed to burn 1 ft³ of propane with 15 in 100 excess air?

Show solution
  1. \[\text{C}_3\text{H}_8 + 5\text{O}_2 \rightarrow 3\text{CO}_2 + 4\text{H}_2\text{O}\]
  2. \[\text{air} = \frac{5}{0.2095} \times 1.15 = 27.4 \text{ ft}^3\]

Answer: About 27.4 volumes of air for each volume of propane, nearly three times as much as natural gas needs; that is why burners are not interchangeable between the two fuels without changes.

Worked problem

Problem 8: motor current

A 100 hp, 460 V three-phase motor has a full-load efficiency of 0.94 and power factor of 0.88. Estimate its full-load current.

Show solution
  1. \[I = \frac{P_{out}}{\eta\,\sqrt{3}\,V\cos\varphi} = \frac{100 \times 746}{0.94 \times 1.732 \times 460 \times 0.88} = 113 \text{ A}\]

Answer: About 113 A. Leaving out the √3 gives 196 A, and leaving out the efficiency gives 106 A; both are typical distractors.

After the paper

Okonkwo finished with eleven minutes left and used them to check the units on every calculation. On Wednesday Grazyna marked it: twenty-one of twenty-five. Two of the four he missed were the same mistake, a gauge pressure taken into a gas law, and she made him write "absolute?" at the top of every page of his binder. The third was a wet steam enthalpy where he had used h_g. The fourth was a sling problem where he had measured the angle from the vertical and used the formula for the horizontal; she said that one was worth knowing because the examiners set both versions. She gave him the next paper the following week.

Grazyna's advice for the months ahead was the same she had given every candidate she had coached: a page of mixed problems every week until the examination, worked from memory and checked; the error log from PWR-240 kept up; and a formula sheet rewritten from scratch every month, because writing it from memory is how it stays in memory. The rest of the Third Class courses, on turbines, boilers and codes, would use every formula on it.

The formula sheet

Grazyna's blank formula sheet was the first question on the paper, though it carried no marks: Okonkwo had to fill it from memory before he could start. The point was not that he would be allowed a sheet in the examination room, because he would not, but that writing the formulas out from memory, with every symbol and unit defined, shows at once which ones have not yet stuck. His finished sheet, checked against the course, looked like the table below. Each line is one that a third class candidate should be able to write down without hesitating and rearrange for any of its quantities.

Okonkwo's formula sheet, as he rewrote it from memory before the practice paper.
TopicFormulaNotes
Heat in a flowing liquidQ = ṁ c ΔTQ = 500 × gpm × ΔT for water
Two-leg slingT = W ÷ (2 sin θ)θ measured from the horizontal
Centripetal forceF = mω²r, ω = 2πN ÷ 60Radians per second, not r/min
Thin cylinderσ_h = pD ÷ 2t, σ_L = pD ÷ 4tDivide by ligament efficiency at tube holes
Thermal stressσ = EαΔTIndependent of length when fully restrained
Steady flow energyq − w = h₂ − h₁Throttling: h₂ = h₁
Wet steamh = h_f + x h_fgSame form for s; v ≈ x v_g
Rankine efficiencyη = (w_t − w_p) ÷ (h₁ − h₄)w_p = v_f Δp
General gas lawp₁V₁ ÷ T₁ = p₂V₂ ÷ T₂Absolute pressure and temperature
Isentropic compressionT₂ ÷ T₁ = (p₂ ÷ p₁)^((γ−1)/γ)γ = 1.4 for air
Exchanger dutyQ = UA ΔT_lmLMTD from the two end differences
Pipe frictionh_f = f (L ÷ D)(V² ÷ 2g)f from Moody, Colebrook or Swamee-Jain
Excess air checkEA ≈ O₂ ÷ (20.9 − O₂)Dry basis oxygen
Three-phase powerP = √3 V_L I_L cos φLine values

Grazyna's comment on the sheet was about what was missing rather than what was there. He had written the formulas but not their limits: the thin-cylinder formulas hold only when the wall is thin; the gas laws only for gases far from condensing; the square law for pipe friction only in turbulent flow. "The examiners love a question where the formula is right and the situation is wrong," she wrote in the margin. He added a column of conditions the next week.

Common mistakes

  • MistakeSpending ten minutes on one hard calculation in the first pass.

    InsteadMark it, move on and come back; secure the quick marks first.

  • MistakeLeaving questions blank.

    InsteadA blank scores nothing; an educated guess among four options scores one time in four, better after eliminating one or two.

  • MistakeChoosing the option nearest an unchecked answer.

    InsteadIf the answer is not among the options, look for a slip from the list of traps before choosing.

  • MistakeStudying only the topics that are comfortable.

    InsteadUse the error log to find weak topics, and spend most practice time there.

  • MistakeMemorizing formulas in one fixed form.

    InsteadLearn what each formula means and how to rearrange it; examiners ask for any of its quantities.

Summary and key terms

  • Ohio's stationary steam engineer examination is 50 questions in three hours, closed book, with 70 in 100 to pass and a block of math formula questions.
  • Experience routes include 2,000 boiler or turbine hours, or shorter experience with an approved 125-hour course.
  • A fixed method of read, sketch, list, name the principle, estimate, calculate and check is fastest under pressure.
  • Wrong options are built from predictable slips: gauge for absolute, Celsius or Fahrenheit for absolute, diameter for radius, missing √3 and others.
  • Two passes, no blanks and a check of the units make the most of the time.
  • Regular mixed practice, an error log and a rewritten formula sheet build the speed the examination needs.
PSI
The testing company that delivers Ohio's boiler operator and stationary steam engineer examinations.
Distractor
A wrong option in a multiple-choice question, often built from a common error.
Error log
A record of missed practice questions, with the mistake and the correct reasoning, used to target study.
Formula sheet
A candidate's own summary of formulas with their symbols and units, rewritten from memory as a study aid.
Qualifying experience
The documented operating time a jurisdiction requires before a certificate or license is issued.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. A gas at 30 psig and 68 °F is heated at constant volume to 176 °F. Find its final gauge pressure (atmosphere 14.7 psia).

    Show answer

    p₂ = 44.7 × 635.67 ÷ 527.67 = 53.8 psia, or 39.1 psig.

  2. Steam at 150 psia is 0.95 dry (h_f = 330.7, h_fg = 863.8 Btu/lb). Find its enthalpy.

    Show answer

    330.7 + 0.95 × 863.8 = 1,151.3 Btu/lb.

  3. A two-leg sling has each leg at 30° to the vertical. A 2,200 lb load hangs from it. Find each leg's tension.

    Show answer

    Legs at 60° to the horizontal: 2,200 ÷ (2 × 0.866) = 1,270 lbf.

  4. The license examination has 50 questions in 180 minutes. You have 40 minutes left and 15 questions to go. Are you on pace?

    Show answer

    Yes: 2.7 minutes per question remaining, a little under the 3.6 average but enough for most.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz