PWR-310 · Lesson 12 of 12 · 34 min

Third class problem practice

▶ Video coming soon A video version of this lesson is on the way.

On the night of Monday, September 7, 2026, Labour Day, Okonkwo Demarest found an envelope in the study binder with his name on it. Inside was a practice paper Grazyna Wolanski had put together from the summer's work: twenty-five questions, a formula sheet left deliberately blank, and a note: "Ninety minutes. No phone. Bring it to me Wednesday." The plant was quiet after the long weekend, and Desmond Kirwan agreed to cover the rounds for an hour and a half after the 02:00 readings. In the morning a new trainee, Tamar Ellingsen, would start her first day shift; Okonkwo wanted the paper done before he went home.

This lesson pulls the course together the way an examination does. It describes the Third Class examinations and how candidates qualify for them, sets out a method for calculation questions that works under time pressure, lists the traps examiners build into the wrong answers, and works a set of mixed problems drawn from every lesson of the course.

The examinations

In Ontario, Third Class operating engineer certificates are issued by TSSA under the Operating Engineers regulation, O. Reg. 219/01. Candidates write four multiple-choice papers, 3A-1, 3A-2, 3B-1 and 3B-2, based on the Third Class syllabus of the Standardization of Power Engineer Examinations Committee (SOPEEC). TSSA's guide gives 150 questions and three and a half hours for each paper, a pass mark of 65 in 100 on each, and a rewrite after 60 days for a failed paper. Papers can be written in any order and alongside the experience; the certificate must be obtained within five years of passing a paper. Other provinces that use the SOPEEC syllabus set papers of their own length, so a candidate outside Ontario checks the local authority's current guide.

The first paper, 3A-1, is where this course's material sits: applied mathematics, applied mechanics, thermodynamics and the science behind the codes. The calculations of PWR-340 (code calculations), PWR-330 (boilers and combustion control) and PWR-320 (turbines) appear in 3A-2 and the B papers, and they all rest on what this course covered. ELEC-210 and lesson 11 cover the electrotechnology.

Qualifying

Ontario's guide asks for 1,920 hours of qualifying experience, either as chief operating engineer of a fourth class plant or as a fourth class operating engineer in a plant of third class or higher, with at least a third of it in boiler operation and no more than a third in maintenance of regulated equipment; a full-time TSSA-approved Third Class program reduces the requirement to 160 hours. The experience is certified on TSSA's testimonial form by the chief engineer. Okonkwo's hours at Cantwell already met the requirement; his plan was to write 3A-1 in February 2027, then 3A-2 in the spring, and the B papers after he had finished the rest of the Third Class courses.

A method for calculation questions

Under time pressure, a fixed routine is faster than inspiration. Grazyna's version, which she had written inside the cover of Okonkwo's binder, has seven steps:

  • Read the question twice. Underline what is asked, and note whether the answer is wanted per unit mass, per hour, in gauge or absolute pressure, or in a particular unit.
  • Sketch it. A box for the boiler, an arrow for each stream, a free-body diagram, a triangle. Most errors of sign and direction disappear on a sketch.
  • List the data with units, converting at once to consistent ones: absolute pressure and temperature, metres or feet, seconds or hours.
  • Name the principle: energy balance, equilibrium, continuity, gas law, Fourier, LMTD. Then write the formula in symbols before putting numbers in.
  • Estimate the size of the answer.
  • Calculate, keeping intermediate values in the calculator.
  • Check the units and the estimate, then find the answer among the options. If it is not there, look for the slip before guessing.

With 150 questions in 210 minutes, a 3A paper allows about 1.4 minutes per question. Many are short recall questions that take seconds, which leaves several minutes for each long calculation. A sensible plan is a first pass answering everything quick, marking the long calculations; a second pass working them; and a few minutes at the end to check that every answer is marked, since an unanswered question scores nothing and a guess among four options scores one time in four.

The traps in the wrong answers

The wrong options in a calculation question are rarely random. They are the answers given by predictable slips, and knowing the list helps a candidate catch them:

Common slips that examiners build distractors around.
SlipWhere it appearsThe check
Gauge pressure used as absoluteGas laws, steam tables, compressor ratiosAdd atmospheric pressure before any gas law or table
Celsius or Fahrenheit used as absoluteGas laws, Carnot, radiation, entropyKelvin or Rankine wherever a temperature multiplies or divides
Diameter used for radiusAreas, torque, centripetal force, cylinder conductionWrite A = πD²/4 or πr², and check which symbol the formula uses
Revolutions per minute used as radians per secondCentripetal force, kinetic energy, power from torqueω = 2πN ÷ 60
Missing √3Three-phase power and currentLine values: P = √3 V I cos φ
Arithmetic mean for LMTDHeat exchangersUse (ΔT₁ − ΔT₂) ÷ ln(ΔT₁ ÷ ΔT₂)
Dryness ignoredWet steam enthalpy and volumeh = h_f + x h_fg
Difference of efficienciesEnergy savingsInput = output ÷ efficiency; subtract inputs
Energy units mixedWork and heat together1 kWh = 3,600 kJ (1 Btu = 778 ft·lbf; 1 kWh = 3,412 Btu)

Practice problems

The problems below are typical of Grazyna's paper. Work each before reading the solution.

Worked problem

Problem 1: required shell thickness

A cylindrical vessel of 1,200 mm inside diameter is to hold 1,500 kPa gauge. Using the simple thin-cylinder relation with an allowable stress of 110 MPa and a joint efficiency of 1.0, what wall thickness is needed, before any corrosion allowance?

Show solution
  1. Rearrange σ = pD ÷ 2t for t:
  2. \[t = \frac{pD}{2\sigma} = \frac{1.5 \times 1{,}200}{2 \times 110} = 8.2 \text{ mm}\]

Answer: About 8.2 mm. The code formula for a real vessel adds terms that make the result slightly larger, and a corrosion allowance; PWR-340 covers it.

Worked problem

Problem 2: general gas law

A gas at 400 kPa absolute and 30 °C occupies 0.50 m³. It is compressed to 0.20 m³ and its temperature rises to 90 °C. Find the final pressure.

Show solution
  1. \[p_2 = p_1 \frac{V_1}{V_2} \frac{T_2}{T_1} = 400 \times \frac{0.50}{0.20} \times \frac{363.15}{303.15} = 1{,}198 \text{ kPa abs}\]

Answer: About 1,198 kPa absolute. The distractor built on Celsius temperatures would give 3,000 kPa.

Worked problem

Problem 3: steam generation and fuel

A boiler makes 9,000 kg/h of dry saturated steam at 1,136 kPa absolute (h_g = 2,781.8 kJ/kg) from feedwater at 105 °C (h_f = 440.3 kJ/kg). Its efficiency is 0.82 on natural gas with an HHV of 37.3 MJ/m³. Find the heat added to the steam and the gas burned per hour.

Show solution
  1. Heat per kilogram and in total:
  2. \[q = 2{,}781.8 - 440.3 = 2{,}341.5 \text{ kJ/kg}, \qquad Q = \frac{9{,}000 \times 2{,}341.5}{3{,}600} = 5{,}854 \text{ kW}\]
  3. Fuel:
  4. \[\dot{V} = \frac{5{,}854}{0.82 \times 37{,}300} \times 3{,}600 = 689 \text{ m}^3\text{/h}\]

Answer: About 5,850 kW into the steam and 689 m³/h of gas.

Worked problem

Problem 4: torque from power and speed

The backup feed pump turbine delivers 56 kW at 3,600 r/min. Find its output torque.

Show solution
  1. \[\omega = \frac{2\pi \times 3{,}600}{60} = 377 \text{ rad/s}, \qquad T = \frac{P}{\omega} = \frac{56{,}000}{377} = 149 \text{ N·m}\]

Answer: About 149 N·m. Using 3,600 directly in place of ω would give 15.6 N·m, a factor of 9.5 too small.

Worked problem

Problem 5: sizing an oil cooler

A lubricating oil cooler must remove 30 kW, cooling oil from 60 to 45 °C with cooling water warming from 25 to 35 °C in counterflow. With U = 300 W/m²·K, what area is needed?

Show solution
  1. End differences: 60 − 35 = 25 K and 45 − 25 = 20 K.
  2. \[\Delta T_{lm} = \frac{25 - 20}{\ln(25/20)} = 22.4 \text{ K}, \qquad A = \frac{30{,}000}{300 \times 22.4} = 4.46 \text{ m}^2\]

Answer: About 4.5 m². The arithmetic mean, 22.5 K, gives almost the same answer here because the end differences are close; with very different end differences the error grows.

Worked problem

Problem 6: pump and motor power

A pump delivers 25 L/s of cold water (998 kg/m³) against 60 m of head. Pump efficiency is 0.72 and motor efficiency 0.93. Find the shaft power and the electrical input.

Show solution
  1. \[P_s = \frac{998 \times 9.81 \times 0.025 \times 60}{0.72} = 20.4 \text{ kW}, \qquad P_{in} = \frac{20.4}{0.93} = 21.9 \text{ kW}\]

Answer: About 20.4 kW at the shaft and 21.9 kW from the supply.

Worked problem

Problem 7: air for propane

How much air is needed to burn 1 m³ of propane with 15 in 100 excess air?

Show solution
  1. \[\text{C}_3\text{H}_8 + 5\text{O}_2 \rightarrow 3\text{CO}_2 + 4\text{H}_2\text{O}\]
  2. \[\text{air} = \frac{5}{0.2095} \times 1.15 = 27.4 \text{ m}^3\]

Answer: About 27.4 volumes of air for each volume of propane, nearly three times as much as natural gas needs; that is why burners are not interchangeable between the two fuels without changes.

Worked problem

Problem 8: motor current

A 75 kW, 600 V three-phase motor has a full-load efficiency of 0.94 and power factor of 0.88. Estimate its full-load current.

Show solution
  1. \[I = \frac{P_{out}}{\eta\,\sqrt{3}\,V\cos\varphi} = \frac{75{,}000}{0.94 \times 1.732 \times 600 \times 0.88} = 87 \text{ A}\]

Answer: About 87 A. Leaving out the √3 gives 151 A, and leaving out the efficiency gives 82 A; both are typical distractors.

After the paper

Okonkwo finished with eleven minutes left and used them to check the units on every calculation. On Wednesday Grazyna marked it: twenty-one of twenty-five. Two of the four he missed were the same mistake, a gauge pressure taken into a gas law, and she made him write "absolute?" at the top of every page of his binder. The third was a wet steam enthalpy where he had used h_g. The fourth was a sling problem where he had measured the angle from the vertical and used the formula for the horizontal; she said that one was worth knowing because the examiners set both versions. She gave him the next paper the following week.

Grazyna's advice for the months ahead was the same she had given every candidate she had coached: a page of mixed problems every week until the examination, worked from memory and checked; the error log from PWR-240 kept up; and a formula sheet rewritten from scratch every month, because writing it from memory is how it stays in memory. The rest of the Third Class courses, on turbines, boilers and codes, would use every formula on it.

The formula sheet

Grazyna's blank formula sheet was the first question on the paper, though it carried no marks: Okonkwo had to fill it from memory before he could start. The point was not that he would be allowed a sheet in the examination room, because he would not, but that writing the formulas out from memory, with every symbol and unit defined, shows at once which ones have not yet stuck. His finished sheet, checked against the course, looked like the table below. Each line is one that a third class candidate should be able to write down without hesitating and rearrange for any of its quantities.

Okonkwo's formula sheet, as he rewrote it from memory before the practice paper.
TopicFormulaNotes
Heat in a flowing liquidQ = ṁ c ΔTc ≈ 4.19 kJ/kg·K for water (Q = 500 × gpm × ΔT for water)
Two-leg slingT = W ÷ (2 sin θ)θ measured from the horizontal
Centripetal forceF = mω²r, ω = 2πN ÷ 60Radians per second, not r/min
Thin cylinderσ_h = pD ÷ 2t, σ_L = pD ÷ 4tDivide by ligament efficiency at tube holes
Thermal stressσ = EαΔTIndependent of length when fully restrained
Steady flow energyq − w = h₂ − h₁Throttling: h₂ = h₁
Wet steamh = h_f + x h_fgSame form for s; v ≈ x v_g
Rankine efficiencyη = (w_t − w_p) ÷ (h₁ − h₄)w_p = v_f Δp
General gas lawp₁V₁ ÷ T₁ = p₂V₂ ÷ T₂Absolute pressure and temperature
Isentropic compressionT₂ ÷ T₁ = (p₂ ÷ p₁)^((γ−1)/γ)γ = 1.4 for air
Exchanger dutyQ = UA ΔT_lmLMTD from the two end differences
Pipe frictionh_f = f (L ÷ D)(V² ÷ 2g)f from Moody, Colebrook or Swamee-Jain
Excess air checkEA ≈ O₂ ÷ (20.9 − O₂)Dry basis oxygen
Three-phase powerP = √3 V_L I_L cos φLine values

Grazyna's comment on the sheet was about what was missing rather than what was there. He had written the formulas but not their limits: the thin-cylinder formulas hold only when the wall is thin; the gas laws only for gases far from condensing; the square law for pipe friction only in turbulent flow. "The examiners love a question where the formula is right and the situation is wrong," she wrote in the margin. He added a column of conditions the next week.

Common mistakes

  • MistakeSpending ten minutes on one hard calculation in the first pass.

    InsteadMark it, move on and come back; secure the quick marks first.

  • MistakeLeaving questions blank.

    InsteadA blank scores nothing; an educated guess among four options scores one time in four, better after eliminating one or two.

  • MistakeChoosing the option nearest an unchecked answer.

    InsteadIf the answer is not among the options, look for a slip from the list of traps before choosing.

  • MistakeStudying only the topics that are comfortable.

    InsteadUse the error log to find weak topics, and spend most practice time there.

  • MistakeMemorizing formulas in one fixed form.

    InsteadLearn what each formula means and how to rearrange it; examiners ask for any of its quantities.

Summary and key terms

  • Ontario's Third Class is four multiple-choice papers of 150 questions in 3.5 hours each, with 65 in 100 to pass each.
  • Experience is 1,920 hours as a fourth class engineer in a qualifying plant, or 160 hours after an approved full-time program.
  • A fixed method of read, sketch, list, name the principle, estimate, calculate and check is fastest under pressure.
  • Wrong options are built from predictable slips: gauge for absolute, Celsius or Fahrenheit for absolute, diameter for radius, missing √3 and others.
  • Two passes, no blanks and a check of the units make the most of the time.
  • Regular mixed practice, an error log and a rewritten formula sheet build the speed the examination needs.
SOPEEC
The Standardization of Power Engineer Examinations Committee, which sets the common power engineer syllabi used by most Canadian jurisdictions.
Distractor
A wrong option in a multiple-choice question, often built from a common error.
Error log
A record of missed practice questions, with the mistake and the correct reasoning, used to target study.
Formula sheet
A candidate's own summary of formulas with their symbols and units, rewritten from memory as a study aid.
Qualifying experience
The documented operating time a jurisdiction requires before a certificate or licence is issued.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. A gas at 200 kPa gauge and 20 °C is heated at constant volume to 80 °C. Find its final gauge pressure (atmosphere 101.3 kPa).

    Show answer

    p₂ = 301.3 × 353.15 ÷ 293.15 = 363.0 kPa abs, or 261.7 kPa gauge.

  2. Steam at 1,000 kPa absolute is 0.95 dry (h_f = 762.7, h_fg = 2,014.4 kJ/kg). Find its enthalpy.

    Show answer

    762.7 + 0.95 × 2,014.4 = 2,676.4 kJ/kg.

  3. A two-leg sling has each leg at 30° to the vertical. A 1,000 kg load hangs from it. Find each leg's tension.

    Show answer

    Legs at 60° to the horizontal: 9,810 ÷ (2 × 0.866) = 5,664 N.

  4. A 3A paper has 150 questions in 210 minutes. You have 40 minutes left and 30 questions to go. Are you on pace?

    Show answer

    Yes: 1.33 minutes per question remaining, close to the 1.4 average.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz