IRW-340 · Lesson 1 of 12 · 23 min
How the exam is built
▶ Video coming soon A video version of this lesson is on the way.
On Sunday morning, October 18, 2026, Andy Pruszynski unlocked the Crossbeam yard shop at eight o'clock, put the coffee on and set out five chairs around the layout table. Benno Torvik, a third-year apprentice who had spent most of his time on Lionel Hartigan's misc and ornamental crew, was close to the end of his apprenticeship. He had finished his third and last level of in-school training in the spring, his hours were almost complete, and he had booked his Red Seal exam for the end of January. He had asked Andy, who had passed the same kind of exam twenty-five years earlier, whether he would help him get ready. Andy said yes on one condition: that they did it properly, on Sunday mornings, with a plan.
Shay Donnelly, the first-year apprentice, asked if he could sit in. "You won't be writing for a long time," Andy said, "but you'll learn more in five Sundays of review than in a year of guessing." Jules Ostrowski from the rod gang came too, because his own exam, in the reinforcing side of the trade, was a year away. The study group met five Sundays, ending with a full practice exam on November 15. This course follows those mornings. Each lesson reviews part of the trade as the earlier courses in this program taught it, and adds the practice and strategy that turn knowledge into a passing mark.
This first lesson explains how the exam is built: who writes it, what it is based on, how the questions are divided, what kind of questions to expect and what the pass mark means in numbers. Knowing the structure is not a trick. It tells a candidate where the marks are, and it stops the most common mistake, which is studying the parts of the trade one already likes.
The Red Seal program
The Interprovincial Standards Red Seal Program is run jointly by the provinces, the territories and the federal government. For each Red Seal trade, the jurisdictions agree on an occupational standard that describes what a fully qualified tradesperson does, and they build an interprovincial exam from that standard. A tradesperson who passes the exam can have the Red Seal endorsement added to the provincial certificate, and the endorsement is recognized in every province and territory. That recognition is the point of the program: an ironworker certified in Ontario can work in Alberta or Nova Scotia without writing again.
The exam is written by the provinces, not by the colleges or by employers. Questions are drafted and checked by groups of experienced tradespeople from across the country, tried out, and kept secure. Nobody outside that process sees the real questions, and every practice question in this course is original. What candidates can see is the standard the exam is built from and the weighting that says how many questions come from each part of it.
Which exam an Ontario ironworker writes
Ontario has more than one ironworker trade, and each leads to a different Red Seal exam. The table shows the three that matter to Crossbeam's people. All three are non-compulsory in Ontario: a certificate is not required to do the work, but most union and many open-shop employers expect it, and the Certificate of Qualification issued by Skilled Trades Ontario is the proof of skill. Benno is registered in Ironworker (Structural and Ornamental), so he writes the Structural/Ornamental exam. Jules, in the rod gang, will write the Reinforcing exam. A worker in a province that uses the broader Generalist trade writes the Generalist exam, which covers rebar and post-tensioning as well as structural and ornamental work.
| Ontario trade | Training | Red Seal exam written |
|---|---|---|
| Ironworker – Structural and Ornamental (420A) | 6,000 hours: 5,280 on the job and 720 in school, three levels | Ironworker (Structural/Ornamental) |
| Ironworker – Generalist (420B) | About 8,000 hours, including 720 in school | Ironworker (Generalist) |
| Reinforcing Rodworker (452A) | Its own program for rebar and post-tensioning | Ironworker (Reinforcing) |
The occupational standard and the weightings
Each Red Seal exam is built from the trade's Red Seal Occupational Standard, which divides the work into major work activities, then tasks and sub-tasks. The exam weighting says how much of the exam comes from each activity. The Structural/Ornamental exam has 120 questions. Its four activities and their approximate shares are shown in the table, with the number of questions each share works out to. The Generalist exam also has 120 questions but six activities, because it adds reinforcing and post-tensioning; a Generalist candidate studies more topics with fewer questions on each.
| Major work activity | Share of exam | About this many of 120 questions |
|---|---|---|
| A. Common occupational skills | 17 in 100 | 20 |
| B. Rigging, hoisting, positioning and cranes | 31 in 100 | 37 to 38 |
| C. Erection, assembly and installation | 36 in 100 | 43 |
| D. Maintenance and upgrading | 16 in 100 | 19 |
| Major work activity | Share of exam |
|---|---|
| A. Common occupational skills | 12 in 100 |
| B. Rigging, hoisting, positioning and cranes | 26 in 100 |
| C. Reinforcing material | 18 in 100 |
| D. Pre-stressing and post-tensioning | 8 in 100 |
| E. Erection, assembly and installation | 26 in 100 |
| F. Maintenance and upgrading | 10 in 100 |
Worked problem
Turning weightings into questions
The Structural/Ornamental exam has 120 questions. Rigging and cranes are weighted at 31 in 100 and erection at 36 in 100. About how many questions come from each, and what share of the exam do the two make up together?
Show solution
- Rigging and cranes: 120 × 31 ÷ 100 = 37.2, so about 37 questions.
- Erection: 120 × 36 ÷ 100 = 43.2, so about 43 questions.
- Together: 31 + 36 = 67 in 100 of the exam, about 80 questions.
Answer: About 37 rigging questions and 43 erection questions: about 80 of the 120, or two thirds of the exam. A candidate who is weak in either area cannot make it up elsewhere.
What the questions look like
Red Seal exams are multiple choice, with four possible answers and one correct answer for each question. There is no written part and no practical part. The questions are written to test what a journeyperson needs to know on the job, not to trick, and most fall into three kinds.
- Knowledge questions ask for a fact: the name of a part, the meaning of a term, the purpose of a device, the order of steps in a procedure.
- Application questions describe a situation on a job and ask what to do, what is wrong, or what comes next. These are the most common kind, and they reward experience and careful reading.
- Calculation questions give numbers and ask for a result: a sling leg load, a weight, a clearance, a plumbness tolerance, a stair riser. They often include wrong answers that come from a predictable mistake, such as using the wrong trigonometry or forgetting a deduction. Lesson 10 practises them.
A question has a stem, the part that sets up the problem, and four options. Three of the options are distractors, wrong answers chosen because they are tempting. A distractor might be true in a different situation, might be what a careless reader picks, or might be the result of a common error in arithmetic. The skill of answering well is mostly the skill of reading the stem precisely: noticing whether it asks for the first thing to do or the best thing to do, a minimum or a maximum, and which country's or which code's rule.
| Kind of question | Example stem (original) | What it rewards |
|---|---|---|
| Knowledge | What is the purpose of a drift pin? | Knowing the trade's tools and terms |
| Application | A connector finds that a beam's holes do not line up with the column connection by one hole. What should he do first? | Judgment and the right order of actions |
| Calculation | A two-leg bridle lifts a 2,400 kg (5,300 lb) beam with legs at 45 degrees from horizontal. What is the load on each leg? | Setting up and checking a calculation |
Time, pass mark and rules
The exam is written at a Skilled Trades Ontario testing location or another approved centre. Candidates are given four hours for the 120 questions, which is two minutes per question, more than enough for most candidates if the time is managed. The pass mark is 70 in 100. On a 120-question exam, that means at least 84 correct answers. There is no penalty for a wrong answer that this course has found published, so a candidate should answer every question, but candidates should read the candidate guide they receive when booking, because the rules are set by the province and can change.
Results are normally sent within a few weeks. A candidate who does not pass receives a report showing performance in each major work activity, and can rewrite after the waiting period the province sets. The report is valuable, because it shows exactly where to study; a candidate who reads it and adjusts the plan usually passes the second time.
Worked problem
What the pass mark means
Benno's exam has 120 questions and a pass mark of 70 in 100. How many correct answers does he need, and how many can he miss?
Show solution
- Correct answers needed: 120 × 70 ÷ 100 = 84.
- Questions he can miss: 120 − 84 = 36.
Answer: 84 correct, so he can miss up to 36. That sounds generous, but if he is weak in rigging and erection, which hold about 80 of the questions, it disappears quickly.
Other credentials beside the exam
The Red Seal is not the only paper an ironworker carries. Contractors and owners also check training that Ontario requires by law and certifications that clients ask for. The table lists the ones this program has mentioned. None of them replaces the Certificate of Qualification, and the certificate does not replace them.
| Credential | What it covers | Notes |
|---|---|---|
| Working at Heights (CPO-approved) | Fall protection training required for work at heights on Ontario construction projects | Valid for three years; a refresher keeps it current |
| WHMIS | Hazardous products and safety data sheets | Employer-specific training too |
| Elevating work platform training | Boom and scissor lifts | Required before operating |
| CWB welder qualification | Welding to CSA W47.1 and W59 for structural work | Renewed by testing at set intervals |
| Hoisting rigging and signalling training | Signaller duties under the construction regulation | Employer-provided or course-based |
How the exam treats country and code differences
The Red Seal exam is national, so its questions are written to be correct in every province. Where provincial rules differ, as they do for some safety details, questions usually ask about the principle, such as when fall protection is needed or who may give signals, rather than a number that differs from one province to another. A candidate who knows both the principle and Ontario's own number is safe either way. Where a national standard applies across the country, such as CSA standards for steel, welding and rigging equipment, the exam may ask for its specific values.
The practice questions in this course follow the same approach. Where a rule differs between the countries, the question names the rule it is asking about, and the answer gives the reason as well as the number, so that a candidate who meets a differently worded question on the day can still reason to the right answer.
Practice questions
Question 1. A candidate is registered in an Ontario ironworker apprenticeship and wants to know which major work activity carries the most questions on the Structural/Ornamental exam. Options: (a) common occupational skills; (b) rigging, hoisting and cranes; (c) erection, assembly and installation; (d) maintenance and upgrading.
Answer and reasoning: (c). Erection, assembly and installation carries about 36 in 100 of the questions, slightly more than rigging at 31. The distractor (b) is the second-largest area and the most common wrong answer.
Question 2. A question describes a crew landing deck bundles and asks which action comes first. What kind of question is it, and how should it be read? Options: (a) knowledge, read quickly; (b) application, read for the word first; (c) calculation, estimate the answer; (d) trick question, skip it.
Answer and reasoning: (b). It describes a job situation and asks for the order of actions, so the key word is first. Several options may be correct actions, but only one comes first.
Question 3. A candidate has 120 questions and has answered 100 with confidence when 20 minutes remain. What should he do with the rest? Options: (a) leave them blank; (b) answer every one, using elimination and the best guess; (c) answer only the calculation questions; (d) hand in the paper.
Answer and reasoning: (b). Unless the rules say otherwise, a blank answer scores nothing and a guess has a chance, especially after eliminating one or two options.
Common mistakes
MistakeStudying the parts of the trade one already knows well.
InsteadStudy by the weighting: the activities with the most questions get the most hours.
MistakeWriting the Generalist exam from a Structural and Ornamental apprenticeship.
InsteadEach Ontario trade leads to its own Red Seal exam; check which one you are registered for.
MistakeTreating calculation questions as a small part of the exam.
InsteadCalculations appear in rigging, erection, ornamental and common skills questions; practise them every week.
MistakeLeaving questions blank when unsure.
InsteadUnless the rules say otherwise, an educated guess has a chance and a blank has none.
MistakeIgnoring the results report after a failed attempt.
InsteadIt shows performance by area; build the next study plan from it.
Summary and key terms
- A Red Seal exam is built by the provinces from the trade's occupational standard, and passing it adds the Red Seal endorsement, recognized across Canada.
- Ontario's Structural and Ornamental trade (420A) leads to the Structural/Ornamental exam, the Generalist trade (420B) to the Generalist exam, and Reinforcing Rodworker (452A) to the Reinforcing exam.
- The Structural/Ornamental exam has 120 questions weighted 17, 31, 36 and 16 in 100 across four major work activities.
- Questions are multiple choice with four options, and they test knowledge, application and calculation.
- Candidates have four hours, and 70 in 100 is the pass mark: 84 correct of 120.
- Rigging and erection together hold about two thirds of the marks.
- Red Seal endorsement
- A seal added to a provincial certificate showing that the holder passed the interprovincial exam.
- Occupational standard
- The document that describes the work of a trade and the tasks a qualified worker performs.
- Major work activity
- One of the main areas of a trade in the occupational standard, used to weight the exam.
- Exam weighting
- The share of the exam drawn from each major work activity.
- Distractor
- A wrong answer in a multiple-choice question, chosen because it is tempting.
- Joint apprenticeship committee
- A board of union and contractor representatives that runs an apprenticeship program.
- Certificate of completion
- The document issued when an apprentice finishes a registered apprenticeship.
Practice problems
Work each problem on paper first, then reveal the answer to check.
How many questions are on the Structural/Ornamental exam, and how many must be correct to pass?
Show answer
120 questions; 84 correct (70 in 100).
Which Red Seal exam does a 420A apprentice write?
Show answer
Ironworker (Structural/Ornamental).
About how many Structural/Ornamental questions come from maintenance and upgrading at 16 in 100?
Show answer
120 × 0.16 = 19.2, about 19.
What are the three kinds of question described in this lesson?
Show answer
Knowledge, application and calculation.
What does the results report show a candidate who does not pass?
Show answer
Performance in each major work activity.
Lesson quiz · 5 questions
Score 60% or more to complete this lesson.
Create a free account to save your progress, take quizzes and earn a certificate.