GAS-310 · Lesson 10 of 12 · 21 min

Codes for large equipment: CSA B149.3 and approvals

▶ Video coming soon A video version of this lesson is on the way.

Vitale Foods, a family company that makes frozen pizza in a plant on Nebo Road on Hamilton Mountain, had bought a used spiral oven from a closed bakery in Italy. It arrived in October in four crates: a stainless steel enclosure, a conveyor, and a gas burner system rated 700 kW (2,390,000 Btu/h) with a gas train, a control panel full of European components, and a CE mark. On Monday, November 2, the plant engineer, Carlo Vitale, met Maureen and Luis on the plant floor. "Our electrician says it's a plug-and-play machine," he said. "How soon can you hook up the gas?" Maureen opened the control panel, looked at the valves and the flame relay, and shook her head. "Not until it's been approved for use in Ontario," she said. "Let me explain what that takes."

This lesson explains which codes and standards govern large gas equipment in Ontario, what certification or listing means, what happens when a piece of equipment is not certified, how the pressure-vessel side of a boiler is regulated, and what a gas technician's responsibilities are under each. It describes the codes in general terms; on a real job, the current edition of each code and the authority's own adoption documents are the reference.

Certified equipment and the installation code

Almost all gas equipment you install is certified or listed: an accredited certification body has tested a sample design against a product standard and authorized the maker to apply its mark to every unit built to that design. The mark tells the installer and the inspector that the equipment, as built and installed by its instructions, meets the standard. Common product standards include those for gas-fired boilers up to 3.66 MW (ANSI Z21.13 · CSA 4.9), for commercial and industrial gas heating equipment (UL 795), and for direct-fired makeup air heaters (ANSI Z83.4 · CSA 3.7). CSA B149.1-25, in force in Ontario since June 1, 2026 through TSSA's code adoption document FS-279-26, requires gas appliances and components to be certified or approved, and sets out how they are installed: piping, venting, air supply, clearances and testing. For certified equipment, the technician's job is to install, start and service it by the code and the instructions, and not to modify it.

When equipment is not certified: field approval

Large industrial equipment is often built to order, assembled on site, modified, or imported from markets that use different standards, so it may carry no North American certification. In Ontario, such equipment needs a field approval before it may be connected and used. The standard for field approval is CSA B149.3, the code for the field approval of fuel-related components on appliances and equipment. TSSA's Gaseous Fuels code adoption document of 2026 adopts the 2025 edition, which extends the code to hydrogen and hydrogen and natural gas blends and updates its rules for regulators, valves, burners, control systems and hazardous locations, with Ontario amendments. B149.3 sets requirements for the equipment's gas train, safety shutoff valves and proof of closure, pressure switches, ignition and flame safeguard, purge, combustion air proving, wiring and documentation. A field approval engineer inspects the installed equipment, reviews the drawings and test results, witnesses the safety tests, and, when everything complies, attaches a field approval label. Without that label, a gas technician must not connect or light the equipment.

A diagram of the rules for a large gas appliance in Ontario. At the top, the TSSA Act and O. Reg. 212/01, the Gaseous Fuels Regulation, which adopts the codes by code adoption document. Below it, CSA B149.1-25 for installation; CSA B149.3:25 for field approval of fuel-related components on uncertified appliances and equipment; and O. Reg. 215/01 for certificates, with a G.1 needed for appliances over 117 kilowatts. On the bottom row, the maker's instructions for certified appliances; CSA B51 and O. Reg. 220/01 for the boiler and pressure vessel side under TSSA Boilers and Pressure Vessels; and electrical work under the Ontario Electrical Safety Code and ESA.
The main rules for large gas equipment in Ontario.

Boilers: the burner side and the pressure side

A boiler is two things at once: a gas appliance and a pressure vessel. In Ontario, the gas side, meaning the burner, gas train, controls, venting and air supply, comes under the Gaseous Fuels Regulation and CSA B149.1, with B149.3 for uncertified burners. The pressure side, meaning the vessel, its safety valves, its water-level and pressure controls as pressure-vessel fittings, and its registration and periodic inspection, comes under TSSA's Boilers and Pressure Vessels program, O. Reg. 220/01 and CSA B51. A new boiler installation therefore involves both TSSA programs, and the boiler must carry a valid certificate of inspection for its pressure side. The gas technician's work on a boiler must satisfy both sides; a perfect gas train on a boiler with a missing low-water cutoff is still an unsafe boiler.

Ontario does not use NFPA 85 or ASME CSD-1 as such; their subject matter is covered by B149.1, B149.3, the boiler maker's certification and the pressure-vessel rules. You will still see CSD-1 mentioned on boilers built for the whole North American market, because their makers design to it.

The main rules for large gas equipment in Ontario.
RuleWhat it coversWho enforces it
CSA B149.1-25Installation of gas appliances, piping, venting, air supplyTSSA, through O. Reg. 212/01 and the code adoption document
CSA B149.3:25Field approval of uncertified appliances and equipmentTSSA field approval
O. Reg. 215/01Certificates: G.3, G.2, G.1 and othersTSSA
O. Reg. 220/01 and CSA B51Boiler and pressure vessel registration and inspectionTSSA Boilers and Pressure Vessels
Ontario Electrical Safety CodePower wiring to equipmentESA

Worked problem

Which rules apply?

Vitale's oven is rated 700 kW and is not certified for Canada. The same plant has a certified 4,400 kW steam boiler. For each, find the input in Btu/h, and state which certificate is needed to work on it and whether field approval is needed.

Show solution
  1. Oven:
  2. \[700 \times 3{,}412 = 2{,}388{,}400 \text{ Btu/h}\]
  3. Over 117 kW, so a G.1 is needed; not certified, so a B149.3 field approval is needed before use.
  4. Boiler:
  5. \[4{,}400 \times 3{,}412 = 15{,}012{,}800 \text{ Btu/h}\]
  6. Over 117 kW, so a G.1 is needed; certified, so no field approval, but its pressure side is registered and inspected under O. Reg. 220/01.

Answer: Both are G.1 work. Only the oven needs a field approval, and nothing about the oven may be lit until the label is on it.

What the approval needed at Vitale

Maureen walked Carlo through what she had seen. The gas train used valves certified to European standards but not certified for Canada, with a single valve-proving device in place of the proof of closure switches the field approval engineer would expect, and its pressure switches had no markings the engineer would recognize. The flame relay was a European model with no North American listing. The panel's wiring and terminal blocks were sized and marked to European rules. None of that made the oven unsafe in Italy. It meant the oven had to be brought into line with the rules here, and documented, before anyone could approve it.

She listed what Bayline would need from Vitale and the oven's maker: the burner and gas train drawings, the control wiring diagram, the sequence of operation with its timings, the maker's purge calculation, data sheets for every safety component, and the oven's rated input and gas pressure. With those, she would propose replacing the gas train with certified North American components, including two safety shutoff valves with proof of closure, certified low and high gas pressure switches, and a certified burner management system with a self-checking flame detector suitable for the oven's continuous runs. Vitale's electrician would rewire the panel to the Ontario Electrical Safety Code under his own permit. Then the field approval engineer would inspect, review the documents and witness the tests: purge timing, trial times, flame failure response, each interlock, and the valve leak tests. Maureen suggested the plant also call its insurer, whose own engineers often have requirements for process ovens.

What a field approval or field evaluation typically needs. The approving body sets its own requirements.
Document or testWhy it is needed
Burner and gas train drawingsShow every component, its rating and its order
Control wiring diagram and sequence of operationShow how interlocks and timings work
Purge calculationShows the purge clears the oven and its ducts
Component data sheets and certificationsProve each safety component is suitable
Gas piping test recordShows the piping to the oven is tight
Witnessed safety testsProve the system does what the documents say

The gas technician's responsibilities

Whatever the equipment, the technician who connects, starts or services it carries legal and professional responsibilities. Work only within your certificate or the limits your employer and the burner makers set. Never connect or light equipment that requires an approval it does not have. Never modify certified equipment, which voids its certification; a change to a certified burner's gas train or controls may turn it into equipment that needs a field approval. Replace safety components only with parts the maker or the approval allows. Test every safety control you disturb. Keep records: the codes and the inspectors expect service records, test results and safety-control tests to be written down, and in a dispute or an investigation those records protect everyone who did the work properly. And report unsafe conditions as O. Reg. 212/01 requires, by shutting off the gas, tagging the equipment and notifying the owner, and TSSA where the regulation requires it.

Carlo asked how long it would all take. Maureen said that with the drawings in hand, Bayline could have a revised gas train designed and quoted within two weeks, and the oven's maker could probably supply North American components through its export division. The field approval inspection could be booked for mid-December if the parts arrived, with the oven in production in January, written into Bayline's plan as targets. "It's slower than plug and play," she told him. "But you'll have an oven that the next technician, the inspector and your insurer can all understand, and that your night shift can run without wondering what happens when the flame goes out."

Hydrogen blends and gas the equipment was not certified for

The 2025 editions of CSA B149.1 and B149.3, now adopted in Ontario, add requirements for hydrogen and natural gas blends, because Canadian utilities have begun pilot projects that blend small amounts of hydrogen into the natural gas supply. Hydrogen burns faster and hotter than methane, has a lower heating value per cubic metre, and can embrittle some metals and affect some seals, so equipment and piping must be suitable for the blend they receive. Unless the utility tells you otherwise, the gas you work with is ordinary natural gas, but you may meet the topic on new equipment data plates and in the codes. The general rule is the same for any fuel: equipment is certified or approved for particular gases, and converting it to another gas, whether propane, a hydrogen blend or biogas, is done only with the maker's conversion kit and instructions, or through an approval.

Inspections and records over the equipment's life

Approval and commissioning are only the beginning. Over a large burner's life, TSSA inspects boilers periodically under the pressure-vessel rules and may inspect fuel installations; owners must keep their equipment maintained and safe under O. Reg. 212/01; and B149.3 and the burner makers set testing and maintenance expectations for field-approved equipment. Insurers often add their own requirements and inspections. Bayline's service reports are written with these in mind: each annual service on a commercial burner records the safety tests performed and their results, the valve leak tests, the switch trip points, the flame signals and the combustion readings, so that the owner can show any inspector what was done and when.

Owners and operators also have daily and weekly duties that a technician should explain at handover: watching the boiler's pressure and temperature, checking for lockouts and alarms, testing the low-water cutoff on steam boilers by the maker's method, and keeping a log. On a large plant, operating engineers do this as their job. In a school or apartment building, it may be a caretaker with little training, and the technician's explanation may be all the training they get.

Responsibilities over a large burner's life.
WhoTypical duties
Owner or operatorDaily and weekly checks, log, calling for service, keeping the room clear
Service technicianAnnual and seasonal service, safety tests, valve tests, tuning, records
TSSA inspectorsPeriodic pressure-vessel inspection and certificates
Insurer's engineersTheir own inspections and requirements

Common mistakes

  • MistakeConnecting uncertified equipment because it carries a foreign mark.

    InsteadA foreign mark is not North American certification; obtain the approval the authority requires first.

  • MistakeModifying a certified burner's train or controls.

    InsteadChanges void the certification and may require a field approval or evaluation.

  • MistakeTreating a boiler only as a gas appliance.

    InsteadThe pressure side has its own rules, registration and inspections.

  • MistakeAssuming the newest edition of a code is the one enforced.

    InsteadCheck which edition the authority has adopted, and any amendments.

  • MistakeFailing to record safety tests.

    InsteadWrite down every safety test and result; inspectors and investigators will ask.

Summary and key terms

  • Most gas equipment is certified to a product standard and installed under CSA B149.1-25, in force in Ontario since June 1, 2026, following the maker's instructions without modification.
  • Uncertified equipment in Ontario needs a TSSA field approval under CSA B149.3, whose 2025 edition Ontario adopted in 2026; appliances over 117 kW are G.1 work.
  • Boilers are also pressure vessels under O.
  • Reg. 220/01 and CSA B51.
  • Technicians must work within their limits, never connect unapproved equipment, never modify certified equipment, test and record every safety control, and report unsafe conditions.
Certification
Testing of a design to a product standard and authorization to mark units built to it.
Pressure vessel
A vessel that holds fluid under pressure, such as a boiler, regulated for its construction and inspection.
Field approval
Inspection and approval of an individual uncertified appliance or piece of equipment on site.
CSA B149.3
The Canadian code for field approval of fuel-related components on appliances and equipment.
Code adoption document
TSSA's document that adopts a code edition in Ontario, with amendments.
G.1 certificate
The Ontario gas technician certificate needed for appliances over 117 kW.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. What standard governs field approval of uncertified gas equipment in Ontario?

    Show answer

    CSA B149.3.

  2. Why can't a technician modify a certified burner's gas train?

    Show answer

    It voids the certification and may make the equipment need a field approval or evaluation.

  3. Which TSSA program registers boilers as pressure vessels?

    Show answer

    Boilers and Pressure Vessels, under O. Reg. 220/01.

  4. What did Vitale's oven need before it could be lit?

    Show answer

    A TSSA field approval under B149.3, with a North American gas train and controls.

  5. Name three documents an approval typically needs.

    Show answer

    Gas train drawings, the wiring diagram and sequence of operation, and the purge calculation; also component data sheets.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz