Sign in or create a free account to continue.

GAS-110 · Lesson 1 of 12 · 20 min

The gas trade and where gasfitters work

▶ Video coming soon A video version of this lesson is on the way.

Jonah Clarke started at Bayline Gas & Heating on Tuesday, September 8, 2026. He had finished the general trades courses, could read a tape and a drawing, and knew how to work safely on a construction site. He did not yet know much about gas. On his first morning, Rosa Delgado, the G.1 gas technician he would work beside for the year, handed him a combustion analyzer in its case and a bottle of leak-detection solution. "These two tools tell you most of what you need to know about a gas job," she said. "One tells you whether the gas is staying in the pipe. The other tells you whether it is burning the way it should. Everything else we learn this year is about keeping both answers right."

This course is the first gas course in the gas technician program. It covers what natural gas and propane are, how they behave and burn, how pressure and flow are measured, why carbon monoxide is the hazard that most often hurts people, how leaks are found and handled, and the safety rules, permits and inspections that govern the work. Later courses build on it: the gas codes, electricity for gas technicians, residential and commercial appliances, venting, controls and troubleshooting. This first lesson describes the trade itself: who does the work, where it is done, who regulates it, and how a new apprentice fits in.

What the trade does

Gasfitters install, test, start up, service and repair the piping and equipment that carry and burn fuel gas. The two main gases are natural gas, piped to buildings by a utility, and propane, stored on site in cylinders or tanks. The work runs from the outlet of the utility's meter, or the outlet of the propane supplier's first regulator, to the appliances and their vents. Within that span a gasfitter may:

  • size, install and support gas piping, and pressure test it before it is used;
  • set regulators and check pressures at meters, manifolds and appliances;
  • install appliances such as furnaces, boilers, water heaters, fireplaces, ranges, dryers, unit heaters, rooftop units, generators and commercial kitchen equipment;
  • supply combustion and ventilation air and install the vents that carry flue gases outdoors;
  • wire and adjust the controls and safety devices on appliances;
  • start up appliances, measure their gas input and analyze their combustion;
  • service, clean and repair appliances and find faults when they do not work;
  • convert appliances from one gas to another with the manufacturer's kit; and
  • respond to complaints about gas odours, carbon monoxide alarms and poor performance.

The common thread is that a mistake can kill. A small leak in a closed room can build up to a flammable mixture. A burner starved of air or a blocked vent can fill a home with carbon monoxide that nobody can see or smell. Because of that, gas work is one of the most tightly regulated trades. A person may do gas work only if they hold the certificate or licence that covers it, the work must follow the adopted code, and most new installations need a permit and an inspection.

Where gasfitters work

Bayline's 22 people do a typical mix of work for a mid-sized gas contractor. Most of their calls are residential: replacing furnaces and water heaters, installing fireplaces and ranges, and answering no-heat calls through the winter. A second crew does light commercial work, such as rooftop heating and cooling units on plazas, unit heaters in garages, and restaurant equipment. Luis Ferreira's crew handles propane: rural homes, farm buildings, construction heaters and conversions. Across the industry, gasfitters also work for:

Where gasfitters are employed
EmployerTypical work
Residential service and installation contractorsFurnaces, boilers, water heaters, fireplaces, ranges, dryers and their venting; maintenance plans; no-heat calls
Commercial and industrial mechanical contractorsRooftop units, make-up air units, boilers, process burners, kitchen equipment, large piping systems
Gas utilitiesMeter sets, service lines, leak response, emergency calls and safety inspections at the customer's request
Propane suppliersTank and cylinder installation, regulator stations, leak checks before filling, delivery and conversion work
Equipment manufacturers and distributorsStart-up and warranty service, technical support, training
Facilities and institutionsIn-house maintenance of hospitals, schools, plants and apartment buildings

Many gasfitters also hold refrigeration, sheet metal or plumbing qualifications, because heating, cooling and ventilation equipment are often installed together. In small towns one technician may do all of it.

A simplified diagram of a gas supply. On the left, the utility side: a distribution main under the street, a service line, the meter and the service regulator. A vertical dashed line marks the point of delivery at the meter outlet. On the right, the customer side, the gasfitter's work: the building piping with a shutoff valve and sediment trap at each appliance, a furnace and a water heater, and their vents to outdoors. A second smaller path shows a propane tank with a first-stage regulator and a second-stage regulator feeding a building.
The gasfitter's work usually starts at the outlet of the meter or the propane supplier's regulator and ends at the vent terminal outdoors.

Who regulates the work

In Canada, gas work is regulated by each province or territory, and every one of them bases its rules on two national standards written by CSA Group: CSA B149.1, the Natural Gas and Propane Installation Code, and CSA B149.2, the Propane Storage and Handling Code. A new edition is published about every five years, and each province adopts it, sometimes with amendments, by its own regulation or code adoption document. In Ontario, the regulator is the Technical Standards and Safety Authority (TSSA), which administers the Technical Standards and Safety Act, 2000 and its fuels regulations: O. Reg. 212/01 for gaseous fuels, O. Reg. 211/01 for propane storage and handling, and O. Reg. 215/01 for the certificates that technicians must hold. Ontario adopted the 2025 edition, CSA B149.1-25, through a code adoption document that took effect on June 1, 2026, and the propane code CSA B149.2:25 through a separate adoption document effective June 8, 2026. Other provinces have their own authorities, such as Technical Safety BC, the Technical Safety Authority of Saskatchewan and Manitoba's Office of the Fire Commissioner, and their own adoption dates.

The certificates matter as much as the code. In Ontario, a person may do gas work only if they hold a TSSA certificate whose scope covers it. The G.3 is the entry certificate, earned after modules 1 to 9 of the gas technician training, about 180 hours; a G.3 holder works within the limited scope that O. Reg. 215/01 sets out. The G.2 adds modules 10 to 24 and covers most residential and light commercial appliances. The G.1 adds the large-appliance modules and at least 4,000 hours of field experience as a G.2, including 500 hours on appliances over 400,000 Btu per hour under a G.1's supervision. The contractor must also be registered with TSSA. Ontario calls the trade gas technician; most other provinces, including Alberta, British Columbia and Saskatchewan, use the word gasfitter, with Class A and Class B certificates.

The gas utility has a role too. It owns the main, the service line and the meter, and it controls when gas is turned on to a new or altered system. Utility technicians respond to emergency odour calls, and in most places only the utility may set or remove a meter.

How an apprentice learns

Jonah's year follows the pattern of most gas apprenticeships. He takes classroom training in blocks, learns on the job under Rosa's direct supervision, and logs his hours. On the job he will start with tasks that build habits: carrying and setting up the test gauges, leak testing joints Rosa has made, cleaning burners, and reading rating plates. As his skill and certificate allow, he will make joints, set appliances, and finally start them up, always with a qualified person checking the work.

Rosa gave him three rules on the first day. First, never work outside your certificate, even when someone asks you to. Second, never leave a job with a gas leak, a carbon monoxide problem or a disabled safety device: make it safe, tag it and tell the customer and the office. Third, write everything down, because a gas installation lasts decades and the next technician needs to know what was done and why.

Habits Rosa expects from the first week
HabitWhy it matters
Read the rating plate before touching an applianceIt tells you the gas type, input, pressures and clearances the appliance was certified for
Leak test every joint you make or disturbMost leaks are at joints that were just worked on
Measure, do not guessPressure, input and combustion readings show problems the eye cannot
Check the vent before and afterA vent that worked yesterday can be blocked or disconnected today
Carry a personal CO monitorIt warns you before symptoms do
Document the workInspectors, customers and the next technician rely on the record

The work is changing

The trade is changing in several ways that a new apprentice should know about. High-efficiency condensing appliances, which vent through plastic pipe and produce acidic condensate, have replaced most older appliances in new homes. Electronic ignition and modulating burners have replaced standing pilots. Heat pumps are taking over more heating, often with a gas furnace kept as backup in cold weather, so gasfitters increasingly work on hybrid systems. Some utilities are testing blends of hydrogen in natural gas, and codes and certificates are being updated for it; training programs are adding hydrogen content as the rules catch up. And codes keep changing: a technician who learned the trade twenty years ago has worked under four or five code editions.

What does not change is the chemistry and physics of gas. A flammable gas still burns only within a narrow range of mixtures with air. A flame still needs the right amount of air to burn cleanly. Pressure still pushes gas through pipes and out of leaks. The rest of this course sets out those basics, because every rule in the code rests on them.

Worked problem

Logging apprenticeship hours

Jonah's first block runs from September 8 to November 13, 2026, ten weeks. He works 8.5-hour days, Monday to Friday, except for the Thanksgiving holiday on Monday, October 12. He also spent two days of the block in a safety course that his program counts as classroom time, not field time. How many field hours does he log in the block?

Show solution
  1. Count the working days in ten weeks:
  2. \[10 \times 5 = 50 \text{ days}\]
  3. Remove the holiday and the two course days:
  4. \[50 - 1 - 2 = 47 \text{ days}\]
  5. Multiply by the hours per day:
  6. \[47 \times 8.5 = 399.5 \text{ hours}\]

Answer: Jonah logs 399.5 field hours in his first block. Recording them weekly, with the job addresses and the supervising technician, is what his program and any later certificate application will ask for.

A day in the trade

Jonah's third Thursday shows what an ordinary day looks like. The truck leaves the shop at 7:30 with a schedule Priya built the night before. The first call is a water heater replacement in a split-level house. Rosa and Jonah check the old unit's venting and gas line, shut off and disconnect it, carry it out, set the new one, connect the gas with a new shutoff valve and sediment trap, leak test, fill the tank, light it, check the manifold pressure, test the draft at the draft hood, and walk the homeowner through the controls. The second call is a furnace that short-cycles; a dirty flame sensor is the cause, and Rosa shows Jonah how to read the control board's flash code before touching anything. After lunch, they rough in a gas line for a kitchen renovation, run a pressure test and leave the gauge on the line for the inspection. The last call of the day is a carbon monoxide alarm that turns out to be fifteen years old and past its end of life; Rosa tests every appliance anyway before recommending a new alarm.

By 4:30 Jonah has carried, measured, tested and written more than he expected. Every job involved a gas line, a burner, a vent and a customer, and every one ended with a record of what was found and done.

Working with customers

Most gas work happens in people's homes and businesses, often when something has gone wrong and the customer is cold, worried or both. Rosa's habits are simple: introduce yourself, protect floors and furniture, explain what you are going to do before you do it, and explain what you found in plain language afterward. When a repair is needed for safety, say why in terms the customer can understand, put it in writing, and never let the customer's budget or impatience talk you into leaving a hazard. Customers remember technicians who are honest about safety, and those technicians get called back.

Trades that work alongside gasfitters
Related trade or certificateHow it overlaps with gas work
Refrigeration and air conditioningRooftop units, heat pumps and hybrid systems combine gas heat with cooling
Sheet metalDuctwork, plenums and some venting for furnaces and air handlers
PlumbingWater heaters, boilers and their water piping; some jurisdictions license plumbers for gas piping
ElectricalPower supplies and branch circuits feeding appliances, done by electricians
Oil burner technicianFuel-fired heating with a similar combustion and venting basis

Common mistakes

  • MistakeDoing a small gas job outside your certificate or licence because "it's only a connector".

    InsteadWork only within the scope of the certificate or licence you hold, however small the task.

  • MistakeAssuming the newest code edition applies everywhere.

    InsteadUse the edition the jurisdiction has adopted, with its amendments.

  • MistakeTreating the utility meter as part of the customer's system you may adjust.

    InsteadThe meter and service regulator belong to the utility; only the utility sets, adjusts or removes them.

  • MistakeLeaving a job with a known hazard because the customer refused the repair.

    InsteadMake the appliance safe, shut it off and tag it, explain the hazard in writing and report it as your rules require.

Summary and key terms

  • Gasfitters install, test, start up, service and repair fuel gas piping, appliances, controls and vents, from the meter or propane regulator outlet to the vent terminal.
  • The work is regulated because leaks can ignite and poor combustion produces carbon monoxide.
  • In Canada each province adopts CSA B149.1 and B149.2; Ontario adopted the 2025 editions in June 2026 under TSSA. Ontario certifies individuals as G.3, G.2 and G.1 gas technicians and registers contractors. The utility owns the meter and controls gas turn-on.
  • Apprentices learn under direct supervision and log their hours.
Gasfitter
A person certified to install and service gas piping and appliances; Ontario's term is gas technician.
Point of delivery
The point, usually the meter outlet, where the utility's system ends and the customer's piping begins.
Authority having jurisdiction
The body that adopts and enforces the code in a place and approves the work.
Code adoption
The legal step that makes a published code edition, with any amendments, the rule in a jurisdiction.
Rating plate
The label on an appliance that gives its gas type, input, pressures, electrical data and clearances.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. Name four kinds of employers that hire gasfitters.

    Show answer

    Residential contractors, commercial mechanical contractors, gas utilities, propane suppliers, manufacturers and facilities departments.

  2. Which two CSA standards does every province base its gas rules on?

    Show answer

    CSA B149.1, the installation code, and CSA B149.2, the propane storage and handling code.

  3. Why does the edition adopted by the jurisdiction matter more than the newest edition?

    Show answer

    Only the adopted edition, with its amendments, is the law that inspectors enforce on that job.

  4. What three rules did Rosa give Jonah?

    Show answer

    Work only within your certificate, never leave a known hazard unmade-safe, and document everything.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz