PWR-210 · Lesson 3 of 12 · 26 min

Work, power and efficiency

▶ Video coming soon A video version of this lesson is on the way.

On Thursday, October 1, 2026, the electrical utility's monthly bill arrived at Cantwell, and Grazyna Wolanski left it on the control room desk with a question written across the top: "Which motor in this plant costs us the most to run, and what does it actually do with the energy?" Tamar Ellingsen started with the boiler feed pumps, because she could hear them from the desk. By the end of the day she had worked out how much of each kilowatt reaching the motor ended up lifting water into the boiler, and the answer surprised her.

This lesson covers work and energy, power, the link between mechanical work and heat, efficiency for single machines and for chains of machines, and how to work out the power a pump puts into the water it moves. Lesson 10 returns to pumps in more detail.

Work

In mechanics, work is done when a force moves its point of action along the direction of the force. The work done is the force times the distance moved in the direction of the force. Holding a heavy valve still is tiring but does no mechanical work; lifting it does.

\[W = F \times s\]

In US customary units, work is measured in foot-pounds (ft·lb): the work done when a force of one pound moves through one foot. Heat is measured in Btu, and the two are linked by the mechanical equivalent of heat, 1 Btu ≈ 778 ft·lb. In SI, work and heat are both measured in joules (J).

Worked problem

Lifting a motor

The crew lifts a spare feed pump motor weighing 550 lb onto a platform 20 ft above the boiler room floor with a chain block. How much work is done on the motor? If the lift takes 30 s, what is the average power?

Show solution
  1. Work done:
  2. \[W = 550 \times 20 = 11{,}000 \text{ ft·lb}\]
  3. Average power in ft·lb/s:
  4. \[P = 11{,}000 \div 30 \approx 367 \text{ ft·lb/s}\]
  5. In horsepower (550 ft·lb/s each):
  6. \[367 \div 550 \approx 0.67 \text{ hp}\]

Answer: 11,000 ft·lb of work, at an average of about 0.67 hp, roughly what a strong worker can sustain for a short time. With a chain block of efficiency 0.75 (lesson 2), the person pulling the hand chain actually does about 11,000 ÷ 0.75 ≈ 14,700 ft·lb.

Energy and its forms

Energy is the capacity to do work. A power plant is, more than anything, a place where energy changes form. The chemical energy in natural gas becomes heat in the flame, the heat becomes the internal energy of steam, the steam's energy drives a turbine or warms a customer's building, and electrical energy runs the pumps and fans. Each change loses some energy as low-temperature heat that can no longer be used, but none of it disappears: the law of conservation of energy says energy cannot be created or destroyed, only changed from one form to another. Lesson 12 uses that law to balance the plant's energy books.

Forms of energy in a district energy plant.
Form of energyWhere it appears at Cantwell
ChemicalNatural gas and fuel oil before they burn
Heat (thermal)Flame, flue gas, steam, condensate, hot water
Kinetic (motion)Moving water in pipes, spinning pump impellers and turbine rotors
Potential (height)Water held up in the deaerator above the feed pumps
Pressure energyWater and steam under pressure in the drums and lines
ElectricalSupply to motors, controls and lighting

Potential energy is the energy a body has because of its height: mass times gravitational acceleration times height in SI, or weight times height in US units. Kinetic energy is the energy of a moving body: half its mass times its speed squared. A raised deaerator gives the water in it potential energy that becomes pressure at the feed pump suction, which lesson 10 shows is what keeps the pump from cavitating.

\[E_p = m \, g \, h \qquad E_k = \tfrac{1}{2} \, m \, v^2\]

Power

Power is the rate of doing work or of transferring energy: work divided by the time taken. Two pumps that lift the same water to the same height do the same work, but the one that does it in half the time needs twice the power.

\[P = \frac{W}{t}\]

In US customary units, mechanical power is measured in horsepower (hp), 550 ft·lb per second, and heat flow in Btu per hour. Electrical power is measured in watts and kilowatts in both systems, and 1 hp is about 0.746 kW, or about 2,545 Btu/h.

Energy is power times time. That is how the utility bills the plant: in kilowatt-hours (kWh), the energy used by a load of one kilowatt for one hour. One kilowatt-hour is 3,600 kJ, or about 3,412 Btu.

Efficiency

No real machine delivers all the energy put into it. Some is lost as heat through friction, electrical resistance, turbulence in the fluid and leakage. The efficiency of a machine is its useful output divided by its input, both in the same units of energy or power. It is a number less than 1, often written in hundredths.

\[\eta = \frac{\text{output}}{\text{input}}\]

When several machines are connected in a chain, so that the output of one is the input of the next, the overall efficiency is the product of the individual efficiencies. A motor of efficiency 0.90 driving a pump of efficiency 0.65 has an overall efficiency of 0.90 × 0.65 = 0.585. Multiplying efficiencies, never adding them, is the key.

\[\eta_{\text{overall}} = \eta_1 \times \eta_2 \times \eta_3 \times \dots\]
A chain of energy conversions for a feed pump: electrical power into the motor, shaft power out of the motor into the pump, and hydraulic power into the water. Each stage shows a smaller arrow, with the losses drawn as heat leaving the side.
Energy losses along a motor and pump chain: overall efficiency is the product of the stage efficiencies.

The power a pump gives the water

A pump does work on water by raising its pressure. The useful power it gives the water, the hydraulic power (also called water power), depends on how much water it moves and how much pressure, or head, it adds. Head is pressure expressed as the height of a column of the liquid that would produce it; lesson 6 explains it. The pump's shaft power is larger than the hydraulic power by the pump's losses, and the motor's electrical input is larger again by the motor's losses.

In US customary units, the hydraulic power in horsepower (water horsepower) is the flow in US gallons per minute times the head in feet times the specific gravity, divided by 3,960:

\[\text{WHP} = \frac{Q_{\text{gpm}} \times H_{\text{ft}} \times SG}{3{,}960}\]

where specific gravity (SG) is the density of the liquid divided by the density of cold water. The 3,960 comes from 8.33 lb per gallon and 33,000 ft·lb per minute per horsepower.

Worked problem

Feed pump power

Boiler 3's feed pump delivers 55 gpm of feedwater at about 221 °F (specific gravity about 0.95) against a head of 430 ft. The pump efficiency is 0.65 and the motor efficiency is 0.90. Find the water horsepower, the brake (shaft) horsepower and the electrical input in kW.

Show solution
  1. Water horsepower:
  2. \[\text{WHP} = \frac{55 \times 430 \times 0.95}{3{,}960} \approx 5.67 \text{ hp}\]
  3. Brake horsepower:
  4. \[\text{BHP} = 5.67 \div 0.65 \approx 8.73 \text{ hp}\]
  5. Motor input:
  6. \[8.73 \div 0.90 \approx 9.70 \text{ hp} \approx 9.70 \times 0.7457 \approx 7.23 \text{ kW}\]

Answer: About 5.7 hp reaches the water, 8.7 hp at the shaft and about 7.2 kW from the supply. The overall efficiency is 0.65 × 0.90 ≈ 0.585: only about 58 parts in 100 of the electricity ends up in the water. The rest becomes heat in the motor windings, the bearings and the turbulent water inside the pump casing.

That was the number that surprised Tamar. Then she worked out the cost. Each feed pump runs whenever its boiler fires, about 8,000 hours a year.

Worked problem

What the feed pump costs to run

The feed pump motor draws about 7.23 kW for 8,000 h a year. At an average of 0.12 dollars per kWh, what is the energy use and the yearly cost?

Show solution
  1. Energy:
  2. \[7.23 \times 8{,}000 \approx 57{,}840 \text{ kWh}\]
  3. Cost:
  4. \[57{,}840 \times 0.12 \approx 6{,}940 \text{ dollars}\]

Answer: About 57,800 kWh and about 6,940 dollars a year for one pump, at sample prices. Raising the pump's efficiency from 0.65 to 0.75 by replacing a worn impeller would cut the shaft power by about 13 in 100 and save roughly 900 dollars a year.

Work, heat and the first law

Mechanical work and heat are two forms of the same thing, energy, and one can become the other. A brake turns the work of a moving vehicle into heat; a steam turbine turns heat into work. The amount is fixed by the mechanical equivalent of heat, which in SI is built into the units (both are joules) and in US units is 778 ft·lb per Btu.

The first law of thermodynamics is the conservation of energy applied to heat and work: the energy added to a system as heat, minus the work the system does, equals the increase in its stored energy. For a steady-flow device such as a boiler, a pump or a heat exchanger, the first law says that the energy entering with the fluid, plus any heat and work added, equals the energy leaving with the fluid. Lessons 7 and 12 use this every time they find the heat needed to make steam.

The heat lost in the feed pump is not wasted entirely: much of it warms the feedwater slightly on its way to the boiler. In a pump that is running against a closed valve, though, all of the shaft power goes into the trapped water, which heats up quickly and can flash to steam inside the casing. That is why feed pumps have a minimum flow recirculation line back to the deaerator, and why an operator never runs a centrifugal pump dead-headed for long.

Worked problem

How fast a dead-headed pump heats its water

If the feed pump's full shaft power of about 8.7 hp (about 6.5 kW, or about 22,200 Btu/h) went into the 44 lb of water trapped in its casing, how fast would the water temperature rise? Use 1 Btu/(lb·°F).

Show solution
  1. Heat added each minute:
  2. \[22{,}200 \div 60 = 370 \text{ Btu/min}\]
  3. Temperature rise per minute:
  4. \[370 \div (44 \times 1) \approx 8.4 \text{ °F per minute}\]

Answer: About 8.4 °F a minute. Starting from 221 °F in a casing at full discharge pressure, the water is already near its boiling point at suction pressure, so it would begin to flash and the pump could be damaged within minutes. Real pumps have some heat loss to the casing, but the lesson stands.

Efficiency across the plant

Efficiency appears at every level of a plant, and an operator should know roughly what to expect. A large electric motor is typically 0.90 to 0.96 efficient; a centrifugal pump 0.50 to 0.85, depending on size and condition; a gas-fired steam boiler about 0.80 to 0.85; a small steam turbine driving a pump perhaps only 0.30 to 0.50 (typical figures). The overall efficiency of turning fuel into useful work is the product of all the steps, and it is always much lower than any single step.

Typical efficiencies (rounded). Actual values depend on size, design and condition.
DeviceTypical efficiencyWhere the losses go
Large electric motor0.90 to 0.96Heat in windings and core, friction, fan
Centrifugal pump0.50 to 0.85Turbulence, recirculation inside the casing, friction
Gas-fired steam boiler0.80 to 0.85Hot flue gas, radiation from the casing, blowdown
Small steam turbine0.30 to 0.50Steam leaving still hot, friction, leakage
Chain block0.40 to 0.80Friction in gears and sheaves

Cantwell's backup feed pump is driven by a 75 hp steam turbine instead of a motor, so that the boilers can still be fed if the electricity fails. The turbine is far less efficient than a motor, but its exhaust steam goes to the deaerator, where its heat warms the feedwater. Counting that heat, the turbine-driven pump wastes much less energy than its efficiency alone suggests. Lesson 12 returns to this idea: an efficiency figure depends on what you count as useful output.

What Tamar told Grazyna

Tamar's answer went back on the bill: the hot water loop pumps used the most electricity, because they ran all year; the feed pumps came second. Of every kilowatt-hour into a feed pump motor, a little under 60 parts in 100 ended up as pressure in the water. Grazyna read it and added one line. "Now check whether the pump is still at 0.65. Worn impellers drift down every year, and nobody notices until someone does this sum." Lesson 10 shows how to do that from pressure gauges and a flow reading.

Common mistakes

  • MistakeAdding efficiencies in a chain of machines.

    InsteadMultiply them: overall efficiency is the product of the stage efficiencies.

  • MistakeConfusing work with force, or power with energy.

    InsteadWork is force times distance; power is work per unit time; energy is power times time.

  • MistakeUsing the pump's hydraulic power as the motor's electrical load.

    InsteadDivide by the pump and motor efficiencies to get the input.

  • MistakeTreating 1 kWh and 1 kW as the same kind of quantity.

    InsteadA kilowatt is a rate; a kilowatt-hour is an amount of energy.

  • MistakeRunning a centrifugal pump against a closed discharge for long periods.

    InsteadAll its shaft power heats the trapped water; use the minimum flow line.

Summary and key terms

  • Work is force times distance moved in the direction of the force; energy is the capacity to do work.
  • Power is the rate of doing work; energy used is power times time, billed in kilowatt-hours.
  • Efficiency is output divided by input; overall efficiency is the product of the stage efficiencies.
  • Water horsepower is gpm × feet × SG ÷ 3,960; brake and electrical power are larger by the pump and motor losses.
  • Heat and work are both energy; the first law of thermodynamics says energy is conserved.
  • A dead-headed pump turns all its shaft power into heat in the trapped water.
Work
Force times the distance moved in the direction of the force.
Power
The rate of doing work or transferring energy.
Efficiency
Useful output divided by input.
Hydraulic power
The power a pump gives to the liquid it moves.
Kilowatt-hour
The energy used by a one-kilowatt load in one hour.
First law of thermodynamics
Energy is conserved: heat added minus work done equals the change in stored energy.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. A force of 100 lb moves a load 12 ft. How much work is done?

    Show answer

    1,200 ft·lb.

  2. A 4 hp motor runs at full load for 10 h. About how much energy does it deliver?

    Show answer

    About 29.8 kWh (4 × 0.7457 × 10).

  3. A motor of efficiency 0.92 drives a pump of efficiency 0.70. What is the overall efficiency?

    Show answer

    About 0.64.

  4. A pump delivers 100 gpm against 99 ft of head (SG 1.0). What is the water horsepower?

    Show answer

    2.5 hp.

  5. How many ft·lb are equivalent to 1 Btu?

    Show answer

    About 778 ft·lb.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz