INS-430 · Lesson 10 of 12 · 60 min

Calculation practice

▶ Video coming soon A video version of this lesson is on the way.

Calculation questions are a small share of the exam but a large share of the marks people lose, because a single slip gives a wrong answer that is, by design, one of the options. Bernie gave calculations their own session in the second half of the afternoon on Sunday, November 8, with Priya, who had been checking Raj's takeoffs all fall, at the whiteboard beside her. "Every one of these has a trap," Bernie said. "The trap is the reason the question exists."

This lesson is a set of worked problems that cover the calculations taught in the program. Each problem gives the method and the answer, and names the trap: the mistake that one of the wrong options would be built from. Work each one yourself before reading the steps. The numbers are the ones used earlier in the program wherever possible, so that the answers can be checked against those lessons.

A method for every calculation

Priya wrote Bernie's five steps on the board, and they work for every problem below.

  • Read for the unknown. Underline what is asked, and note whether it wants a diameter or a radius, a length or an area, a total or a per-meter figure.
  • Write the formula first, in symbols, before any numbers go in. Most slips happen when numbers are written straight into a half-remembered formula.
  • Put every quantity in consistent units. Millimeters with meters, inches with feet, °C differences with a °C coefficient. Convert before calculating, not after.
  • Estimate before you calculate. A rough answer in your head catches a misplaced decimal: a steam pipe will not lose 15 W/m, and a duct will not need 29 m of wrap per piece.
  • Check against the options. If your answer is on the list, ask which mistake the nearby options represent, and make sure you did not make it.
A chart of the common calculation traps with an example of each: thickness not doubled, radius used for diameter, units mixed, rounding the wrong way, the wrong mean temperature, log base 10 instead of natural log, and adding decibels like ordinary numbers.
The traps that distractors are built from.

Pipe, jacket and layout

Worked problem

1. Girth and jacket cut width

NPS 4 pipe (4.500 in) with 2 in of insulation. Find the calculated girth and the cut width with a 2 in lap.

Show solution
  1. D = 4.500 + 2 × 2 = 8.500 in.
  2. Girth = π × 8.5 = 26.70 in.
  3. Cut width = 26.70 + 2 = 28.70 in, about 28 11/16 in (measure the real girth on the job, as in lesson 6).

Answer: About 28 11/16 in. Trap: adding the thickness once gives π × 6.5 = 20.4 in.

Worked problem

2. Sections for a run

A straight run is 80 ft. How many 3 ft sections are needed?

Show solution
  1. 80 ÷ 3 = 26.67.
  2. Round up: 27 sections.

Answer: 27. Trap: rounding to 26 leaves part of the pipe bare.

Worked problem

3. Bands on a straight run

Bands at 9 in on a 80 ft run. How many bands?

Show solution
  1. 960 ÷ 9 = 106.7, so 107 spaces.
  2. Bands = spaces + 1 = 108.

Answer: 108. Trap: forgetting the band at the start gives 107.

Worked problem

4. Mitered elbow segment

Five-piece mitered elbow on NPS 8 long-radius, R = 12 in, insulation outside diameter 14.625 in. Find the heel length of a full segment.

Show solution
  1. Joint angle = 90 ÷ 4 = 22.5°; tan 11.25° = 0.1989.
  2. Heel radius = 12 + 14.625 ÷ 2 = 19.31 in.
  3. Heel = 2 × 19.31 × 0.1989 = 7.68 in.

Answer: 7.68 in. Trap: using the pipe's outside diameter (8.625 in) gives a heel radius of 16.31 in and 6.49 in.

Worked problem

5. Duct wrap stretch-out

Duct 36 × 18 in; the maker's allowance is 8 in. Stretch-out?

Show solution
  1. Perimeter = 2 × (36 + 18) = 108 in.
  2. Stretch-out = 108 + 8 = 116 in.

Answer: 116 in. Trap: the bare perimeter, 108 in, crushes the wrap at the corners.

Worked problem

6. Tank shell area

A tank 5 ft in diameter and 10 ft high has 2 in of insulation. Outer shell area?

Show solution
  1. D = 5 + 2 × 2 ÷ 12 = 5.333 ft.
  2. Area = π × 5.333 × 10 = 167.6 ft².

Answer: 168 ft². Trap: using the tank diameter gives 157 ft², short on jacket.

Worked problem

7. Pins on a wall

A wall 80 in wide takes pins at no more than 18 in. How many spaces and pins across?

Show solution
  1. 80 ÷ 18 = 4.44, so 5 spaces.
  2. 5 spaces need 6 pins across, including one near each edge.

Answer: 5 spaces, 6 pins. Trap: rounding to 4 spaces stretches the spacing past the maximum.

Heat flow

Worked problem

8. Heat flow through a flat surface

A wall is insulated with 2 in of board, k = 0.28 Btu·in/(h·ft²·°F), with 270 °F across it. Heat flow per square foot?

Show solution
  1. q = k ΔT ÷ t = 0.28 × 270 ÷ 2.
  2. = 37.8 Btu/h·ft².

Answer: 37.8 Btu/h·ft². Trap: using the thickness in feet gives 454 Btu/h·ft².

Worked problem

9. Thermal resistance

What is the R-value of 2 in of insulation with k = 0.28 Btu·in/(h·ft²·°F)?

Show solution
  1. R = t ÷ k = 2 ÷ 0.28 = 7.14.

Answer: R-7.1. Trap: k ÷ t gives 0.14.

Worked problem

10. Heat loss from an insulated pipe

NPS 4 pipe, r₁ = 2.25 in, with 2 in of insulation, k = 0.31 Btu·in/(h·ft²·°F) at the mean, 270 °F across the insulation. Heat loss per foot, ignoring the surface film?

Show solution
  1. r₂ = 2.25 + 2 = 4.25 in; ln(r₂ ÷ r₁) = ln(1.889) = 0.6360.
  2. k per foot = 0.31 ÷ 12 = 0.02583 Btu/(h·ft·°F).
  3. q′ = 2π × 0.02583 × 270 ÷ 0.6360 = 68.9 Btu/h·ft.

Answer: About 68.9 Btu/h·ft. Trap: leaving k in Btu·in units gives 12 times too much, 827 Btu/h·ft.

Worked problem

11. Mean temperature

Pipe at 366 °F, jacket at 86 °F. At what mean should k be read?

Show solution
  1. (366 + 86) ÷ 2 = 226 °F.

Answer: 226 °F. Trap: reading k at the pipe temperature overstates it; at room temperature understates it.

Worked problem

12. A year's heat loss

The kettle line loses 76.2 Btu/h·ft over 210 ft, at full pressure 7,550 h a year, at 13.75 dollars per MMBtu (sample). Annual energy and cost?

Show solution
  1. 16,002 Btu/h × 7,550 h = 120.8 MMBtu.
  2. 120.8 × 13.75 = 1,661 dollars.

Answer: About 121 MMBtu and 1,660 dollars. Trap: the 8,400 boiler hours give 134 MMBtu and 1,848 dollars.

Worked problem

13. Expansion of a hot line

A steel line 200 ft long heats from 50 °F to 366 °F. Steel grows 6.5 millionths per °F. How much?

Show solution
  1. 200 × 12 × 316 × 0.0000065 = 4.93 in.

Answer: About 4.9 in. Trap: using the °C coefficient with °F gives 9.1 in.

Worked problem

14. Contraction of a cryogenic line

A stainless line 100 ft long is cooled to liquid nitrogen. Total contraction is 0.28 in 100. How much does it shorten?

Show solution
  1. 1,200 in × 0.0028 = 3.36 in.

Answer: 3.36 in. Trap: treating 0.28 in 100 as 0.028 gives 33.6 in.

Moisture, noise and exposure

Worked problem

15. Dew point

Air at 86 °F and 70 in 100 relative humidity. Dew point?

Show solution
  1. Convert: (86 − 32) ÷ 1.8 = 30 °C; γ = ln 0.70 + 17.62 × 30 ÷ 273.12 = 1.5787.
  2. Tdp = 23.9 °C = 75.1 °F.

Answer: 75 °F. Trap: putting °F into the Magnus formula gives a meaningless number.

Worked problem

16. Adding sound levels

A compressor at 90 dBA and a pump at 84 dBA at the same spot. Total?

Show solution
  1. Total = 10 log₁₀(10⁹·⁰ + 10⁸·⁴) = 10 log₁₀(1.251 × 10⁹) = 91.0 dBA.

Answer: 91 dBA. Trap: adding the numbers (174) or averaging (87).

Worked problem

17. Distance and sound

A valve is 92 dBA at 3 ft. In open space, what is it at 12 ft?

Show solution
  1. Two doublings of distance: 92 − 6 − 6 = 80 dBA.

Answer: 80 dBA. Trap: subtracting 6 once gives 86 dBA.

Worked problem

18. Allowed exposure time

Under OSHA's limit of 90 dBA for 8 hours with a 5 dB exchange rate, how long may a worker be exposed to 95 dBA unprotected?

Show solution
  1. 95 is 5 dB above 90: one halving.
  2. 8 ÷ 2 = 4 hours.

Answer: 4 hours. Trap: using a 3 dB rate gives about 2.5 hours.

Worked problem

19. Time-weighted average

0.15 f/cc for 3 hours and 0.02 f/cc for 5 hours. Eight-hour TWA?

Show solution
  1. (0.15 × 3 + 0.02 × 5) ÷ 8 = 0.55 ÷ 8 = 0.069 f/cc.

Answer: 0.069 f/cc. Trap: averaging the two readings gives 0.085.

Firestop and labor

Worked problem

20. Annular space

NPS 2 pipe (2.375 in) in a 4 in hole. Space when centered, and at the widest point if the pipe touches one side?

Show solution
  1. Centered: (4 − 2.375) ÷ 2 = 0.81 in.
  2. Touching one side: 4 − 2.375 = 1.63 in on the far side.

Answer: 0.81 in centered, 1.63 in at the widest. Trap: checking only the centered figure.

Worked problem

21. Hours from a labor unit

A takeoff has 1,250 ft of pipe at a sample unit of 0.046 h/ft. How many hours, and how many 8-hour days for a crew of two?

Show solution
  1. 1,250 × 0.046 = 57.5 h.
  2. A crew of two works 16 h a day: 57.5 ÷ 16 = 3.6 days.

Answer: About 57 hours, 3.6 days. Trap: dividing by 8 only gives 7.1 days.

Worked problem

22. Conversions to know

Convert a 150 psi header to kPa, 3 in to millimeters and R-7.1 to RSI.

Show solution
  1. 150 × 6.895 = 1,034 kPa.
  2. 3 × 25.4 = 76.2 mm.
  3. 7.1 ÷ 5.68 = 1.25.

Answer: About 1,035 kPa; 76 mm; RSI 1.25.

Problems to try alone

These five problems have answers only. Work them under time pressure, about two minutes each, and check your method against the worked problems above if you miss one.

  • A. NPS 6 pipe (6.625 in) with 2 1/2 in of insulation and a 2 in lap. Cut width from the calculated girth? (Answer: π × 11.625 + 2 = 38.5 in.)
  • B. A run of 138 ft in 3 ft sections, with 5 in 100 added for waste. How many sections? (Answer: 138 × 1.05 ÷ 3 = 48.3, so 49.)
  • C. Two layers: 1 1/2 in with k = 0.28 and 1 1/2 in with k = 0.24 Btu·in/(h·ft²·°F). Total R? (Answer: 5.36 + 6.25 = 11.6.)
  • D. Three sources of 80, 80 and 86 dBA at one spot. Total? (Answer: 80 + 80 = 83; 83 and 86 give about 87.8 dBA.)
  • E. Under OSHA's limit, how long is 100 dBA allowed? (Answer: 10 dB over 90 is two halvings: 8 ÷ 4 = 2 hours.)

Using the calculator

A basic calculator is allowed if the booking confirmation says so, and it is worth practicing with the exact one you will take. Check that it has a π key, a square root, natural logarithms and powers of ten, or know the workarounds: π is 3.1416, and decibel sums can be done with the shortcut table from INS-340 (equal sources add 3 dB, 3 dB apart add about 1.8, 6 dB apart about 1, 10 dB apart about 0.4). Clear the memory before the exam, write down intermediate results instead of trusting the display, and round only at the end. A dead battery in the first hour is a real risk; a spare costs very little.

Estimating before calculating

Bernie made the group estimate every answer before working it. For a girth, the insulated diameter times three is close enough to catch a missed doubling. For a heat loss, a well-insulated steam line loses tens of watts per meter, not hundreds or thousands. For a noise sum, the total is never more than a few decibels above the loudest source. Thirty seconds of estimating saved Erik four marks on the practice exam.

Checking an answer quickly

Once an answer is found, a second method is the best check. A girth can be checked by measuring a section's circumference in your head: a 8 1/2 in insulated diameter is about 27 in round. A section count can be checked by multiplying back: 27 sections of 3 ft cover 81 ft, a little more than the run. A heat loss can be checked by its order of size, and a TWA by noting that it must lie between the lowest and highest readings. If the check fails, rework the problem from the formula, not from the numbers you wrote the first time.

Common mistakes

  • MistakeWriting numbers straight into a formula.

    InsteadWrite the formula in symbols first, then substitute.

  • MistakeMixing millimeters and meters, or inches and feet.

    InsteadConvert to consistent units before calculating.

  • MistakeRounding counts of pieces, spaces or bands down.

    InsteadRound up whenever the count must cover the full length.

  • MistakeUsing log base 10 in the pipe heat-loss formula.

    InsteadUse the natural logarithm, ln.

  • MistakeAdding or averaging decibels.

    InsteadUse the logarithmic rules: equal sources add 3 dB; distance doubling subtracts 6 dB.

Summary and key terms

  • Read for the unknown, write the formula, make units consistent, estimate, then check against the options.
  • Insulated diameter is the pipe's outside diameter plus twice the thickness; girth is π times that diameter.
  • Counts of sections, spaces and bands round up, and a run of spaces needs one more band or pin than spaces.
  • Flat heat flow is kΔT ÷ t; pipe heat flow uses 2πkΔT ÷ ln(r₂ ÷ r₁), with k at the mean temperature.
  • Decibels add logarithmically, and exposure time halves for every exchange-rate step above the limit.
Trap
The specific mistake a wrong option in a multiple-choice question is built from.
Natural logarithm
The logarithm to base e, written ln, used in the pipe heat-loss formula.
Exchange rate
The number of decibels by which the level may rise for each halving of allowed time.
Labor unit
The hours a defined quantity of work is expected to take.
Insulated diameter
The outside diameter of the insulation: pipe outside diameter plus twice the thickness.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. NPS 6 (6.625 in) with 2 1/2 in insulation. Girth?

    Show answer

    π × 11.625 = 36.52 in.

  2. Six-piece 90° mitered elbow: joint and cut angle?

    Show answer

    90 ÷ 5 = 18° joints, 9° cuts.

  3. k = 0.24 Btu·in/(h·ft²·°F), 1 in thick: R?

    Show answer

    1 ÷ 0.24 = 4.2.

  4. Three sources of 85 dBA each. Total?

    Show answer

    85 + 10 log₁₀ 3 = 89.8, about 90 dBA.

  5. 0.08 f/cc for 6 hours and nothing for 2. TWA?

    Show answer

    0.48 ÷ 8 = 0.06 f/cc.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz