GAS-130 · Lesson 3 of 12 · 22 min

Alternating current and household power

▶ Video coming soon A video version of this lesson is on the way.

In the second week of November, Bayline replaced a 30-year-old furnace in a split-level house in Upper Arlington. The new furnace arrived with a wiring sheet that called for a 15-amp circuit, a service switch and a separate receptacle for the condensate pump. Jonah followed Rosa to the electrical panel and watched her read the breaker directory, then trace the old furnace cable through the basement ceiling to a switch at the top of the stairs. "Before we touch anything," she said, "you need to know where this power comes from, what the numbers on the panel mean, and which part of this job is ours and which part belongs to an electrician".

This lesson explains alternating current (AC), how power reaches a house from the utility, how the service panel divides it into branch circuits, and what the electrical code expects of the circuit that feeds a gas appliance. It also sets out where a gas technician's electrical work stops in Ohio.

Direct and alternating current

A battery or a thermocouple produces direct current: its voltage has one polarity, positive and negative, and current flows one way. Utility power is alternating current: the voltage rises from zero to a peak in one direction, falls back through zero, rises to a peak in the other direction and returns, over and over. One complete swing is a cycle, and the number of cycles each second is the frequency, measured in hertz (Hz). In both Canada and the United States, utility power runs at 60 Hz, so the voltage reverses direction 120 times a second.

Alternating current is used for utility power because its voltage is easy to change with a transformer. The utility can generate at one voltage, step it up to hundreds of thousands of volts to send it long distances with little loss, step it down in stages near town, and finally step it down to the voltage a house uses. Lesson 5 explains how a transformer does this, and the 24-volt control transformer inside a furnace works on exactly the same principle.

A sine wave plotted against time for one-sixtieth of a second. The voltage rises from zero to a positive peak of about 170 volts, falls through zero to a negative peak of about minus 170 volts and returns to zero. A dashed horizontal line at 120 volts marks the RMS value. Labels show one cycle equals 1/60 second, about 16.7 milliseconds.
One cycle of 120-volt, 60-Hz household power. The peak is about 170 V; the 120 V that meters display is the RMS value.

Peak and RMS values

Because AC voltage changes all the time, a single number is needed to describe it. The number used is the RMS value, short for root mean square. An AC voltage of 120 volts RMS delivers the same heating power to a resistance as 120 volts of steady DC. Household voltages, nameplate ratings and the readings of ordinary meters are all RMS values unless stated otherwise. For a smooth sine wave, the peak voltage is about 1.414 times the RMS voltage.

Worked problem

Peak voltage of household power

A receptacle measures 120 V AC on a meter. What is the peak voltage, and how large is the swing from the positive peak to the negative peak?

Show solution
  1. Multiply the RMS value by 1.414:
  2. \[V_{\text{peak}} = 1.414 \times 120 \approx 170 \text{ V}\]
  3. The peak-to-peak swing is twice the peak:
  4. \[V_{\text{p-p}} = 2 \times 170 = 340 \text{ V}\]

Answer: The insulation on a 120-volt circuit must withstand peaks of about 170 volts many times a second. This is one reason meter and tool ratings are higher than the circuit's nominal voltage.

Utility voltage is not exact. The nominal 120 volts can normally read anywhere from about 114 to 126 volts at a receptacle depending on the load in the neighborhood and the length of the wiring, and the equipment is designed to tolerate that range. A reading far outside it, such as 100 volts or 135 volts, points to a supply problem, often a loose neutral, and is a matter for the utility or an electrician, not for adjusting the appliance.

From the utility to the panel

Most houses in Columbus are fed by a split-phase service. The utility, AEP Ohio in most of Columbus, brings power to a transformer on a pole or a ground-level pad. The transformer's secondary winding has a connection at its center, called the center tap, which is grounded and becomes the neutral. The two ends of the winding become two hot conductors, often called line 1 and line 2. Between either hot conductor and the neutral there are 120 volts. Between the two hot conductors there are 240 volts, because the two halves of the winding add. Three conductors, two hots and a neutral, run to the house through the utility's meter to the service panel.

In the panel, the main breaker or main switch can disconnect the whole house. The two hot conductors feed two bus bars, and individual circuit breakers clip onto the bars. A single-pole breaker takes one hot and feeds a 120-volt circuit. A double-pole breaker takes both hots and feeds a 240-volt circuit, such as an air conditioner, a heat pump or an electric range. The neutral conductors of all circuits return to the neutral bar, and the grounding conductors to the ground bar. At the main service, and only there, the neutral and ground are connected together and to the grounding electrode, a link that lesson 10 explains.

A utility transformer with a center-tapped secondary feeding a house panel. Line 1 and line 2 come from the ends of the winding and the neutral from the center tap, which is grounded. Labels show 120 volts from line 1 to neutral, 120 volts from line 2 to neutral and 240 volts from line 1 to line 2. In the panel, a single-pole breaker feeds a 120-volt furnace circuit and a double-pole breaker feeds a 240-volt air conditioner.
A split-phase service gives 120 V from either hot to neutral and 240 V between the hots.

Branch circuits, breakers and wire

Each breaker protects a branch circuit: the wiring from the panel to the receptacles, lights or equipment it feeds. The breaker is sized to protect the wire, not the appliance. If current rises above the wire's safe limit, because of an overload or a short, the breaker trips and opens the circuit before the wire overheats. In ordinary house wiring, 14 AWG copper is protected at 15 amps and 12 AWG copper at 20 amps. A furnace normally runs on a 15-amp circuit, and its installation instructions give the maximum overcurrent protection it may have. Fitting a bigger breaker because a circuit keeps tripping removes the protection for the wire and can start a fire; a breaker that trips is telling you something is wrong.

Conductors are identified by color on both sides of the border. Hot conductors are black or red, sometimes blue or another color. The neutral is white or gray. The grounding conductor is green, green with a yellow stripe, or bare copper. In older houses, and in cables used for 240-volt circuits, a white conductor is sometimes used as a hot and should be re-marked with black or red tape. Never assume a conductor's job from its color alone; measure.

Electrical power for an AC load is complicated by motors and transformers, whose current does not rise and fall exactly in step with the voltage. For those loads, volts times amps gives the apparent power, measured in volt-amperes (VA), which is a little more than the real power in watts. The ratio of the two is the power factor. For a heating element they are the same; for a motor they can differ by a fifth or more. That is why transformers are rated in VA, not watts, as lesson 5 explains.

Worked problem

Checking a furnace circuit against its breaker

The new furnace's nameplate lists a total of 9.8 A at 115 V, and the installation sheet says the maximum overcurrent protection is 15 A. The condensate pump plugged into a receptacle on the same circuit draws 1.2 A. What is the total load, and how much of the breaker's rating does it use?

Show solution
  1. Add the currents on the circuit:
  2. \[I_T = 9.8 + 1.2 = 11.0 \text{ A}\]
  3. Express it as a fraction of the breaker rating:
  4. \[\frac{11.0}{15} \approx 0.73\]

Answer: The load uses about 73 in every 100 parts of the breaker's rating. That is acceptable for a furnace circuit, but there is not much room left. Rosa noted it on the work order so that nobody later adds an electronic air cleaner and a humidifier to the same circuit without checking.

What the electrical code asks of a furnace circuit

In Ohio, the National Electrical Code (NFPA 70) is adopted by reference through the state building codes. The 2023 NEC has applied to commercial buildings under the 2024 Ohio Building Code since March 1, 2024, and to houses under the Residential Code of Ohio since April 15, 2024. The City of Columbus issues electrical permits and inspects through Building and Zoning Services. For central heating equipment, NEC section 422.12 calls for an individual branch circuit, with auxiliary equipment directly associated with the heating system, such as a humidifier or condensate pump, allowed on the same circuit. The appliance also needs a disconnecting means, which for a furnace is normally a switch within sight of the unit, often mounted on or beside the cabinet, or a breaker that can be locked in the open position as the NEC section on appliance disconnects allows. The NEC also requires a 125-volt service receptacle within 25 feet of heating and air-conditioning equipment, on the same level, so that a technician does not run cords from elsewhere, and a light at equipment in an attic, crawl space or similar location.

A plan of a basement furnace circuit in Ohio: the panel with a single-pole 15-amp breaker, cable to a service switch within sight of the furnace, then to the furnace junction box, and a separate service receptacle within 25 feet on the same level. Notes: individual branch circuit with associated accessories allowed; disconnect within sight or a lockable breaker; service receptacle within 25 feet.
A typical Ohio furnace circuit under the NEC as adopted. The installation instructions and the local inspector set the details.

Where the gas technician stops

In Ohio, electrical, HVAC and plumbing contractors are each licensed by the Ohio Construction Industry Licensing Board, and the City of Columbus registers contractors and issues the permits. The boundary between HVAC and electrical work is set by state licensing and local rules, and an apprentice should not guess at it. Bayline's rule, set by Hank as the license holder, is simple: Bayline technicians connect appliances to an existing, suitable circuit at the disconnect, and wire the appliance's own controls and low-voltage circuits under the mechanical permit. Any new branch circuit, new disconnect or new receptacle is run by a licensed electrical contractor under an electrical permit. On the Upper Arlington job, the existing circuit and switch were suitable, so Rosa connected the new furnace to them. The service receptacle for the condensate pump was new wiring, so Bayline's electrical partner added it under its own permit.

The principle is the same on both sides of the border. The gas technician owns the appliance, its internal wiring, its controls and its connection to a suitable supply. The electrician owns the supply: the panel, the breaker, the branch circuit and the disconnect. When a job needs both, the work is planned so each trade does its own part, with the right permit or notification, and nobody quietly runs a new circuit because it is quicker.

Back at the split-level

Before disconnecting the old furnace, Rosa had Jonah switch off the furnace switch, test the meter on a known live receptacle, confirm zero volts at the old furnace's junction box between every pair of conductors, and test the meter again on the receptacle. Then they locked the switch off with a padlock and tagged it. When the new furnace was set and its supply connected, Jonah measured 121 volts hot to neutral, 0.2 volts neutral to ground and 121 volts hot to ground at the furnace junction box before the first start, and wrote all three readings on the start-up sheet. Lesson 4 explains why those three readings, and that live-dead-live test, matter.

Common mistakes

  • MistakeFitting a larger breaker because a furnace circuit trips.

    InsteadThe breaker protects the wire; find out why it trips.

  • MistakeAssuming a white wire is always a neutral.

    InsteadWhite conductors are sometimes re-marked hots on 240-volt circuits; measure before you touch.

  • MistakeRunning a new branch circuit because it is "just a furnace job".

    InsteadNew circuits, switches and receptacles belong to the electrical trade with the right permit or notification.

  • MistakeMounting the furnace disconnect where it cannot be reached safely.

    InsteadFollow the adopted code and local guidance on where the disconnect goes.

  • MistakeTreating 120 V as an exact number.

    InsteadA reading from about 114 to 126 V is normal; far outside that is a supply problem.

Summary and key terms

  • Alternating current reverses direction; utility power in Canada and the US runs at 60 Hz.
  • Meters show RMS values; the peak of 120 V AC is about 170 V.
  • A split-phase service gives 120 V from either hot to neutral and 240 V between the hots.
  • Breakers protect the wire, and a furnace normally has a 15-amp circuit with the maximum overcurrent protection listed in its instructions.
  • Hot conductors are black or red, neutrals white or gray, grounds green or bare, but always measure.
  • The NEC as adopted in Ohio expects a furnace on an individual branch circuit with a disconnect within sight or lockable, and a service receptacle within 25 feet.
  • The gas technician works on the appliance; new branch circuits belong to the electrical trade.
Alternating current
Current that reverses direction many times a second; 60 cycles a second in North America.
Hertz
The unit of frequency, one cycle per second.
RMS value
The effective value of an AC voltage or current, equal in heating effect to the same DC value.
Split-phase service
A 120/240-volt supply from a center-tapped transformer, with two hots and a neutral.
Branch circuit
The wiring from the final overcurrent device to the outlets or equipment it serves.
Volt-ampere
The unit of apparent power, volts times amps, used to rate transformers.
Disconnecting means
A switch or breaker that can disconnect the appliance from its supply.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. What is the frequency of utility power in Canada and the US?

    Show answer

    60 Hz.

  2. What voltage is between the two hot conductors of a split-phase service?

    Show answer

    240 V.

  3. What does a breaker protect?

    Show answer

    The branch circuit wiring, against overload and short circuit.

  4. What is the peak of a 120-V RMS sine wave?

    Show answer

    About 170 V.

  5. Who installs a new branch circuit for a furnace?

    Show answer

    A licensed electrical contractor, with the required electrical permit.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz