ROOF-210 · Lesson 3 of 12 · 24 min

Hot asphalt and kettle operation

▶ Video coming soon A video version of this lesson is on the way.

On Wednesday, November 4, it rained, and Marco Lindell spent the morning in the yard with Rory and the kettle. Marco had run Ridgecap's kettles for sixteen years, and at Cedarbrook school in July he had kept one going for five straight weeks. "A kettle is the most dangerous thing we own," he said, slapping the steel lid. "It's a tank of liquid at over 200 degrees, sitting on a propane fire, on a public street. If you treat it like a barbecue, it will hurt somebody. Today you learn to treat it like what it is."

Hot-applied asphalt is still the standard way to build a built-up roof and to set many modified bitumen base sheets and insulation boards. This lesson covers the equipment, the temperatures that matter, how a kettle is loaded and run, how hot asphalt gets to the roof, and the burns, fire and fumes that come with it. Under O. Reg. 213/91, section 211, only a competent worker may operate a kettle or a hot bitumen tanker. This lesson is the classroom part of that training; Marco's sign-off on the job is the rest.

The equipment

A trailer-mounted roofing kettle: insulated vat with a hinged lid, burner tubes under the vat fed from a propane cylinder set at least 3 m away, a thermometer and thermostat, a pump with a discharge line to the roof and a return line, an extinguisher within reach and a barricaded zone around the kettle.
The parts of a roofing kettle and its setup.
  • The vat holds the asphalt. Ridgecap's main kettle holds 1,500 L (about 400 US gal); its small one, 450 L, is used for repairs. The vat is insulated, with a tight-fitting lid that closes to keep heat in, keep fumes down and smother a fire.
  • The burner fires into tubes or flues that run through or under the vat, heating the asphalt without the flame touching it. It is fed by propane through a regulator and hose.
  • The thermometer and, on modern kettles, a thermostat that cycles the burner keep the temperature in the working range. Marco checks the kettle gauge against a hand-held probe thermometer every morning.
  • The pump moves asphalt through an insulated pipe or hose to the roof, with a return line that lets it circulate back to the vat so it does not cool and plug the line.
  • On larger jobs, hot asphalt comes in bulk from a refinery or terminal in an insulated, heated tanker truck that parks on site and pumps to the roof. Tankers avoid handling kegs but bring their own rules about location and burners.
  • On the roof, hot asphalt goes into a lugger (an insulated cart), a mop cart or mechanical spreader, or buckets for detail work.

Temperatures that matter

Rory had heard of EVT in the spring without knowing what it meant. Marco wrote the temperatures on the kettle in chalk from the label on a keg of Type III asphalt.

A thermometer scale for a Type III roofing asphalt: softening point about 85 to 96 °C, equiviscous temperature for mopping about 210 °C with an application range 14 °C either side, the kettle working range below the finished blowing temperature, and the flash point at 260 °C or more at the top, with a no-go band 14 °C below it.
The temperatures that govern hot asphalt work.
Temperatures printed on roofing asphalt labels.
TemperatureWhat it isWhy it matters
Softening pointwhere the asphalt starts to flow (lesson 2)decides the asphalt type and slope it suits
Equiviscous temperature (EVT)the temperature at which the asphalt has the right runniness for the application methodapply at the EVT, within about 14 °C (25 °F) either side, at the point of application
Finished blowing temperature (FBT)the temperature at which the asphalt was finished at the refineryheating above it for long changes the asphalt and lowers its softening point
Flash pointwhere vapour above the asphalt can ignite from a spark or flamenever heat to or near it; stay well below

The EVT depends on the asphalt and the method. A label might give one EVT for mopping by hand and a higher one for a mechanical spreader, which lays a thinner film. For a typical Type III asphalt, one maker gives about 210 °C for mopping and 221 °C for a mechanical spreader. The key words are at the point of application: the asphalt cools on its way from the kettle to the mop, so the kettle runs hotter than the EVT, but never hotter than the label allows.

What goes wrong at the wrong temperature:

  • Too cold: the asphalt is thick, goes on too heavy, skins over before the felt meets it and does not bond. The result is blisters, slippage and wasted asphalt.
  • Too hot: the asphalt goes on too thin, ages in the kettle and loses softening point, fumes heavily and comes closer to its flash point. Long overheating can lower the softening point enough that a roof slides in summer.
  • Far too hot: at or near the flash point, vapour above the vat can ignite. A kettle fire is the most serious emergency a roofing crew has.

The asphalt labels Ridgecap buys state the flash point; for ASTM D312 asphalts it is at least 260 °C, and Ridgecap's rule is that no kettle ever reads within 14 °C of the flash point on the label. Most maker and industry guidance says the same.

Worked problem

Checking the application window

The label gives an EVT of 210 °C for mopping, with a window of 14 °C either side. At the mop cart Rory measures 188 °C. The kettle reads 232 °C. What is the window, is the asphalt in it, and what should change?

Show solution
  1. Window = 210 − 14 to 210 + 14 = 196 to 224 °C.
  2. Measured at the mop: 188 °C, which is 8 °C below the bottom of the window.
  3. The kettle is 232 − 188 = 44 °C hotter than the mop: the asphalt is losing heat on the way.
  4. Raising the kettle risks overheating; first shorten the time in the lugger, insulate or circulate the line, and cover the cart.

Answer: The window is 196 to 224 °C and the asphalt at the mop is 8 °C too cold. The fix is to lose less heat on the way, not simply to turn the kettle up.

Setting up the kettle

Where the kettle goes is the first safety decision of a hot job. Ontario's construction regulation and Ridgecap's rules set the minimum; the site sets the rest.

  • On the ground, never on the roof and never inside a building. Ridgecap's rule matches the model fire codes.
  • Away from building openings, air intakes and combustibles. Ridgecap keeps kettles at least 6 m from doors, windows, air intakes and anything that can burn, matching the 20 ft distance in the International Fire Code. An air intake that sucks in asphalt fumes fills a building with smell and complaints.
  • Inside a barricaded zone, with cones and tape or fencing, so the public and vehicles cannot reach it, and never blocking exits, fire lanes or entrances.
  • On level, firm ground with the wheels chocked and the hitch supported.
  • The propane cylinder at least 3 m from the burner and any other source of ignition, as section 211 requires, with the supply line routed so hot asphalt cannot reach it if something spills or fails.
  • A fire extinguisher rated at least 4A40BC at the kettle, as section 211 requires, and another on the roof.
  • Downwind of the building and the public where possible, and with the lid side away from where people walk.

Loading and running the kettle

Solid asphalt arrives in kegs, paper cartons of 45 kg (100 lb), or in bulk. Marco's loading routine:

  • Check that the kettle is not empty and cold with a crust: start a cold kettle slowly, with the burner on low, so asphalt melts around the flues before the bulk heats. Heating a solid block quickly can trap melted asphalt under a crust and make it erupt.
  • Strip the paper from each keg on the ground; paper in the kettle burns and clogs the pump.
  • Make sure kegs and the vat are dry. Water or snow in hot asphalt turns instantly to steam, makes it foam and boil over, and throws hot asphalt out of the vat. In wet or winter weather, kegs are stored covered and wiped dry.
  • Split kegs into pieces with an axe or keg splitter, wearing a face shield, and lower them in by hand or with a loading tray. Never drop or throw a piece in; it splashes.
  • Do not fill the vat above the maker's line, usually about three quarters full, so the asphalt has room to expand and the lid closes.
  • Keep the lid closed except when loading. Open it standing to the side, with the wind at your back, and never lean over the vat.
  • Read the thermometer at least every 15 minutes and log it. Never leave a lit kettle unattended. The International Fire Code rule Ridgecap follows on both sides of the border is that an attendant stays within 100 ft (30 m) with the kettle in sight.

Worked problem

How many kegs fill the kettle

The main kettle holds 1,500 L and is filled no more than three quarters full. Hot asphalt weighs about 0.9 kg per litre. How many 45 kg kegs make a full working load?

Show solution
  1. Working volume = 1,500 × 0.75 = 1,125 L.
  2. Mass = 1,125 × 0.9 = 1,012.5 kg.
  3. Kegs = 1,012.5 ÷ 45 = 22.5, so 22 kegs, topping up as the level drops.

Answer: About 22 kegs fill the kettle to its working level. On a busy mopping day the crew might use two or three loads.

Getting hot asphalt to the roof

Most burns happen while hot asphalt is moving: being pumped, carried, hoisted or poured. The rules:

  • Pipes carrying hot asphalt up the building must be securely fastened and supported, as section 208 of the construction regulation requires, with joints tight and the line clear of ladders and walkways. The top of the pipe has a valve or a goose-neck over the lugger, and nobody stands under it.
  • Never carry hot asphalt up a ladder. Buckets go up on a hoist or by the pump line, never by hand.
  • Fill buckets no more than about three quarters, and carry them at your side, not in front of you.
  • Keep luggers and mop carts on planks or walk boards on new insulation, and roll them slowly; a wheel dropping into a gap tips the load.
  • Use signals agreed before work starts between the kettle attendant and the roof: pump, stop and circulate. A radio is better than shouting.
  • Flush and drain the line at the end of the day or keep it circulating, so asphalt does not set in it overnight. A plugged line cleared by heating with a torch can burst.

Burns

Hot asphalt at 200 °C or more sticks to skin, keeps burning while it cools and cannot be wiped off. Everyone near hot work wears:

  • A long-sleeved shirt and long pants of heavy cotton or flame-resistant cloth, with sleeves down and pant legs over the boots, not tucked in.
  • Leather or heat-resistant gloves with gauntlet cuffs.
  • Safety glasses, with a face shield at the kettle and when loading or pouring.
  • Work boots, laced high, and a hard hat.

First aid for an asphalt burn, as Marco teaches it:

  • Cool the burn right away under cool, clean running water for at least 20 minutes. Cooling stops the asphalt and the skin under it from burning deeper.
  • Do not try to peel off asphalt stuck to the skin, and do not use solvents, fuel or cleaners on it. Medical staff remove it later.
  • Remove rings, watches and loose clothing near the burn if they are not stuck.
  • Cover loosely with a clean, non-stick dressing, and get medical attention for anything larger than a small spot, any burn to the face, hands, feet or joints, and any burn to the eyes. For eyes, flush with water continuously on the way to care.
  • Report every burn to the foreperson and the safety coordinator.

Fire

If asphalt in a kettle catches fire, the response is practised, not improvised:

  • Shut off the burner and the propane at the cylinder, if it can be reached safely.
  • Close the lid to smother the fire. Most kettle fires go out when the lid closes.
  • Use a dry chemical extinguisher on any fire outside the vat. Never use water on burning asphalt: it turns to steam and spreads the fire.
  • Move people away, call the fire department, and keep everyone back until it is out.

Fumes

Hot asphalt gives off fumes that irritate the eyes, nose and throat and cause headaches. Asphalt fume has an occupational exposure limit under Ontario's regulation on workplace exposure limits, and the workers closest to the kettle and the mop get the highest exposure. Ways to keep it down:

  • Run the kettle at the lowest temperature that gives the right EVT at the mop.
  • Keep the lid closed.
  • Set the kettle downwind and away from air intakes; work with the wind at your back.
  • Use low-fuming asphalts where the specification allows; they have additives that form a skin on the hot surface and cut fumes.
  • Wash before eating, drinking or smoking.

Fumes are also why some buildings cannot have hot asphalt work at all, or only at certain times. At Cedarbrook in July, the school was empty but the daycare in the next block was not, and Marco set the kettle at the far end of the parking lot with the fumes blowing toward the playing fields. At the Ferncliff bakery, the next lesson shows how a building's air intakes changed the whole repair method.

Common mistakes

  • MistakeHeating the kettle as hot as it will go to save time.

    InsteadRun at the label's range so the asphalt is at its EVT at the mop and never near the flash point.

  • MistakeDropping wet kegs into hot asphalt.

    InsteadKeep kegs dry; water causes violent foaming and boil-over.

  • MistakeOpening the lid and leaning over the vat.

    InsteadOpen it standing to the side with the wind at your back, wearing a face shield.

  • MistakePutting water on a kettle fire.

    InsteadShut off the fuel, close the lid and use a dry chemical extinguisher.

  • MistakePeeling asphalt off a burn.

    InsteadCool with running water for at least 20 minutes, leave the asphalt and get medical care.

Summary and key terms

  • Only a competent, trained operator runs a kettle, and it is never left unattended.
  • Apply asphalt at its EVT, within about 14 °C (25 °F) either side, at the point of application.
  • Never heat near the flash point or for long above the finished blowing temperature.
  • Set the kettle on the ground, away from openings, intakes and combustibles, barricaded, with propane at a safe distance and extinguishers at hand.
  • Most burns happen while asphalt is being moved; use hoists and pumps, not ladders, and fill buckets three quarters.
  • Cool asphalt burns with running water for at least 20 minutes and do not remove the asphalt.
Kettle
A heated, insulated tank used to melt and hold roofing asphalt.
Equiviscous temperature (EVT)
The temperature at which an asphalt has the right viscosity for its application method.
Finished blowing temperature (FBT)
The temperature at which the asphalt was finished at the refinery; it should not be exceeded for long.
Flash point
The lowest temperature at which vapour above a liquid can ignite from a spark or flame.
Keg
A paper carton of solid roofing asphalt.
Lugger
An insulated wheeled cart used to carry hot asphalt on the roof.
Boil-over
Violent foaming of hot asphalt caused by water or moisture entering the kettle.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. An asphalt's EVT for mopping is 218 °C with a 14 °C window. What is the range?

    Show answer

    204 to 232 °C.

  2. The flash point on a label is 274 °C. What is the highest kettle reading Ridgecap's rule allows?

    Show answer

    274 − 14 = 260 °C.

  3. A 450 L kettle is filled three quarters full of asphalt at 0.9 kg/L. How many 45 kg kegs is that?

    Show answer

    450 × 0.75 × 0.9 = 304 kg; 304 ÷ 45 = 6.75, about 7 kegs.

  4. What extinguisher does section 211 require at a kettle?

    Show answer

    One rated at least 4A40BC.

  5. Why should water never be used on a kettle fire?

    Show answer

    It flashes to steam and throws burning asphalt.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz