ROOF-110 · Lesson 1 of 12 · 25 min
The roofing trade
▶ Video coming soon A video version of this lesson is on the way.
Every building has a roof, and sooner or later every roof needs a roofer. The roof takes the worst of the weather. On a clear summer afternoon a dark membrane can reach 70 to 80 °C, far hotter than the air. In winter the same roof carries snow, ice and wind, and it freezes and thaws over and over. Rain, hail, ultraviolet light and the building's own warm, moist air work on it all year. When a roof fails, water gets into insulation, ceilings, walls, wiring and stock, and a small leak can turn into a large repair bill. Roofers build, repair and replace the layers that keep all of that out. It is skilled, physical, outdoor work, and on most days it is done at height.
This course is the first roofing course in the Roofer program. It follows Rory Quintero, a first-year apprentice at Ridgecap Roofing in Hamilton, Ontario, through his first season on the tools. Rory's foreperson is Dana Renaud, a journeyperson with 21 years in the trade who runs Ridgecap's Crew 2, the commercial low-slope crew. Dana has one rule she repeats until the apprentices can say it for her: "Plan the roof before you climb it." By the end of the course you will see why. Most of what goes wrong on a roof, from a fall to a fire to a soaked ceiling below, starts with something nobody planned.
Ridgecap is an invented company, but it is a typical one. It employs about 48 field workers in the busy season, split into six crews, plus seven people in the office. About 60 in every 100 dollars of its work comes from commercial and industrial low-slope roofs: strip plazas, warehouses, schools and apartment buildings. About 30 in 100 comes from houses with steep roofs, mostly asphalt shingles with some metal. The rest is sheet metal flashing, gutters and service calls. The owner, Glen Pelham, started as a roofer himself. Anjali Mukherjee, the safety and training coordinator, writes the fall protection plans, issues hot-work permits and keeps the training records. Rory's first week was mostly spent with her.
What roofers do
A roofer's job is to make a roof watertight and keep it that way. That covers several kinds of work:
- New construction: installing the complete roof system on a new building, from the vapour retarder and insulation to the membrane or shingles and the flashings.
- Re-roofing: removing an old roof (a tear-off) and installing a new one, often on an occupied building with people working or living underneath.
- Recovering: installing a new roof over an existing one where the building and the rules allow it, after checking that the old roof is dry and the structure can carry the extra weight.
- Repair and service: finding and fixing leaks, replacing damaged sections, resealing flashings and clearing drains.
- Inspection and maintenance: walking roofs on a schedule, reporting problems and doing small repairs before they grow.
- Sheet metal and flashing: forming and installing metal copings, counterflashings, drip edges, gutters, downspouts and, on some jobs, complete metal roofs.
On any given day a roofer may carry materials, run a kettle or a torch, cut and fit insulation boards, lay membrane, nail shingles, bend metal on a portable brake, seal penetrations around pipes and vents, clean up and load debris. Good roofers also read drawings and specifications, measure roofs, estimate materials and talk with building owners. Forepersons plan the work, set up the safety systems and make sure the roof is watertight before the crew leaves each night.
The sectors of the trade
Roofing splits into a few sectors. Most roofers spend most of their careers in one or two of them, although apprentices are expected to learn the basics of all.
Low-slope roofing covers roofs that look flat from the ground. They are never truly flat; they are built with a slight slope so water drains to roof drains, scuppers or gutters. Commercial, industrial and institutional buildings mostly have low-slope roofs. The main systems are built-up roofing (layers of felt and hot asphalt with a gravel or cap sheet surface), modified bitumen (factory-made sheets of asphalt modified with rubber or plastic, applied with a torch, hot asphalt, cold adhesive or self-adhesive backing), single-ply membranes (sheets of thermoplastic or rubber, such as TPO, PVC and EPDM, welded with hot air or glued at the seams), spray polyurethane foam, and liquid-applied coatings. Low-slope crews are often larger and work with heavier equipment: kettles, torches, hot-air welders, power cutters for tear-off and hoists or cranes for loading.
Steep-slope roofing covers roofs where you can see the roof surface from the street. Houses are the classic example, but churches, small commercial buildings and some condominium projects also have steep roofs. The coverings are shed-type materials that overlap like fish scales so water runs off them: asphalt shingles, metal panels and shingles, clay and concrete tile, slate and wood shakes and shingles. Steep-slope crews tend to be smaller and move between more jobs. The hazards are different too. On a steep roof the surface itself tries to throw you off, so fall protection is needed almost everywhere on the roof, not just near the edges.
Sheet metal work is part of almost every roof. Metal flashings close the joints where a roof meets a wall, a chimney, a skylight, a curb or the edge of the building. Metal copings cap parapet walls. Gutters and downspouts carry water away. Some roofing companies have their own sheet metal shop and mechanics; others buy flashings from a sheet metal contractor. Either way, roofers install a lot of metal and need to understand how it sheds water and how it moves with temperature.
Service and repair is a sector of its own. A good service roofer is part detective: water can travel a long way inside a roof before it shows up on a ceiling, so finding a leak means understanding how the roof was built. Service work also brings roofers onto roofs they did not build, often in bad weather, sometimes alone. That makes planning and fall protection even more important.
| Sector | Typical buildings | Typical materials | Key hazards |
|---|---|---|---|
| Low-slope commercial | plazas, warehouses, schools, apartments | built-up, modified bitumen, TPO, PVC, EPDM, coatings | unprotected edges, skylights, hot asphalt, torches, heavy loads |
| Steep-slope residential | houses, churches, small commercial | asphalt shingles, metal, tile, slate, wood | slope itself, ladders, nail guns, heat, power lines |
| Sheet metal and flashing | all roofs | galvanized steel, aluminum, copper, prefinished steel | sharp edges, edge work, hand cuts, wind on panels |
| Service and repair | any building | whatever is on the roof | unfamiliar roofs, bad weather, working alone |
A day on Crew 2
Rory's first full week was on a tear-off at a small office building. The crew met at the Ridgecap yard at 6:30 in the morning. Marco Lindell, the kettle operator and lead hand, loaded the trailer while Dana went over the day with the crew. The plan covered how much roof would be torn off, how the debris would come down, where the guardrails and barrier lines were, who was on the torch, where the extinguishers would be and what the forecast said about wind and rain. Rory noticed that nobody touched a tool until that talk was done.
On site, the first hour went to setting up. The hoist went up at the back of the building with guardrails on both sides of the landing. The crew set a barrier line back from the open edges and clamped guardrail posts to the low parapet at the front. The disposal bin was placed under the chute, with barricades around it. Only then did the tear-off begin. By early afternoon the torn-off section was covered with new base sheet and the crew was torching the cap sheet. At 2:30 the torch went out for the day. For the next two hours Marco walked every seam and flashing as fire watch while the others cleaned up. At the end of the day the roof was watertight, the debris was gone and the edges were still protected.
"Most of roofing is not the roofing," Dana told him on the drive back. "It's the setup, the loading, the weather, the cleanup and keeping everyone in one piece. If you get those right, the roofing part is the easy part."
Apprenticeship and certification
In Ontario, roofer is a skilled trade with a formal apprenticeship. The trade is listed as Roofer (trade code 449A) and is a Red Seal trade, which means the final certification exam is the Interprovincial Red Seal exam and the certificate is recognized across Canada. In Ontario it is a voluntary trade: you do not need a certificate to work as a roofer, but registered apprentices get structured training, the employer gets a trained worker, and the certificate is proof of skill that many employers and union contracts value. An apprentice signs a registered training agreement with an employer, and the agreement is registered with the Ministry of Labour, Immigration, Training and Skills Development. The program is about 4,000 hours long in total, which includes about 480 hours of in-school training in total, split into two levels of about 240 hours each, usually taken at a college or a union training centre. After completing the hours and the in-school levels, the apprentice can write the Red Seal exam and, on passing, receives a Certificate of Qualification from Skilled Trades Ontario with the Red Seal endorsement.
Rory registered his training agreement in his first month. Ridgecap logs his hours by task: tear-off, low-slope installation, steep-slope installation, flashing, safety systems and so on. Dana signs off on skills as he shows them, and he will attend Level 1 in-school training in the winter, when roofing slows down. Keisha Grant, a second-year apprentice on the steep-slope crew, has already finished Level 1 and warned him that the in-school block includes math, drawings and building science as well as safety.
Licensing and the rules that govern roofing work
Roofing work in Ontario is governed by several layers of rules. The Occupational Health and Safety Act sets out the duties of employers, supervisors and workers, and its construction regulation, O. Reg. 213/91 (Construction Projects), contains specific rules for fall protection, ladders, roof hoists and built-up roofing. Workers who use fall protection must complete a Working at Heights training program approved by the Chief Prevention Officer under O. Reg. 297/13. The Ontario Building Code sets requirements for the roof as a part of the building, and municipal building departments issue permits for some roofing work. The Ontario Fire Code and local fire departments have rules about kettles, propane and hot work. The Ministry of Labour, Immigration, Training and Skills Development enforces the health and safety rules, and its inspectors visit roofing sites, often without notice.
Rules change. Regulations are amended, new training requirements come into force and codes are updated on a cycle. A good roofer does not try to memorize every rule; instead, they know where the rules live, they check the current version and they ask their supervisor or safety coordinator when something is unclear. In this course you will see section numbers and dates so you can look up the rules yourself. Always check that you are reading the current version.
| Who | Main duties on a roofing job |
|---|---|
| Employer | provide training, equipment and safe systems of work; write and enforce procedures; keep records |
| Supervisor or foreperson | plan the work, set up protection, make sure workers follow the rules, tell workers about hazards |
| Worker or apprentice | work safely, use the protection provided, report hazards and injuries, refuse unsafe work |
| Ministry inspector | inspect sites, investigate incidents, issue orders or citations |
| Building owner | tell the contractor about known hazards (for example asbestos or weak decks), give access, coordinate occupants |
Your rights and duties as a new worker
As a worker in Ontario you have three basic rights under the Occupational Health and Safety Act: the right to know about hazards, the right to participate in health and safety (through a joint committee or a health and safety representative on larger projects) and the right to refuse work you believe is likely to endanger you. You also have duties: to work in compliance with the Act and regulations, to use the equipment and protective devices your employer requires and to report hazards and contraventions to your supervisor. Reprisal against a worker for using these rights is prohibited.
New workers are injured far more often than experienced ones, and roofing is one of the construction trades with the highest rate of serious and fatal falls. That is not because new workers are careless. It is because they do not yet know what they do not know. Anjali gave Rory a short list on his first day:
- Ask before you climb. If you do not know how you will be protected on a roof, you are not ready to go up.
- Speak up. If something looks wrong, tell Dana or the lead hand right away.
- Report every injury, including small cuts and burns, the same day.
- Never remove or bypass a guardrail, barrier line or cover without permission and a plan to protect the opening.
- Never work on a roof alone without a check-in plan.
Rory wrote the list in the notebook he keeps in his chest pocket. Dana checks it every Friday.
Skills and habits of a good roofer
Roofing rewards people who are fit, careful and good with their hands, but those are not the only skills. The roofers Rory admires most share a few habits. They read the weather every morning and keep watching it all day. They measure twice and cut once, because wasted membrane and metal cost money. They keep a clean roof, since loose materials and debris are trip hazards and can blow off the roof. They understand how water moves, so they lap materials the right way and never leave a joint that faces uphill. They respect hot work. And they look after their crew.
Math matters too. Roofers work out roof areas and slopes, count bundles and rolls, measure flashing lengths and calculate setbacks for barrier lines. The worked example below shows the kind of planning that apprentices start with: how long the apprenticeship itself takes.
Worked problem
Planning an apprenticeship
Rory's apprenticeship requires about 4,000 hours in total, including about 480 hours of in-school training split into two levels. Ridgecap works 40-hour weeks for about 34 weeks of the year, with Level 1 taken over the winter. Roughly how many seasons will it take Rory to finish if each in-school level takes one winter?
Show solution
- Work hours needed on the job: 4,000 − 480 = 3,520 hours.
- Work hours per season: 40 × 34 = 1,360 hours.
- Seasons for work hours: 3,520 ÷ 1,360 ≈ 2.6 seasons, so Rory should plan on three seasons.
- The two in-school levels fit in the winters between seasons.
Answer: About three seasons, with Level 1 and Level 2 taken in two of the winters. Overtime and winter work can shorten it.
Safety culture on a roofing crew
Roofing has hazards that are easy to see, such as edges, ladders, kettles and torches, and hazards that are easy to miss, such as heat, sun, dust and the slow damage to backs, shoulders and knees from years of lifting and kneeling. A good safety culture deals with both. On Crew 2 that culture shows up in small ways: the daily toolbox talk, the fact that Dana walks the roof before the crew goes up, the habit of calling out "hot" when someone carries a mop of asphalt, and the expectation that anyone can stop the work if something looks wrong.
Safety also depends on the hierarchy of controls, which you met in TRD-101. The most effective controls remove or reduce the hazard itself: a guardrail that stops anyone reaching the edge, a self-adhered membrane that needs no torch near a wood curb, a crane that lifts a pallet instead of a worker carrying bundles up a ladder. Next come procedures and training, such as hot-work permits and lift plans. Personal protective equipment, such as harnesses, gloves and safety glasses, is the last line of defence. You will see this order of thinking in every lesson of this course.
Dana explained it to Rory with an example from his first week. "We could have put everyone in harnesses on that office roof. Instead we used the barrier line and the guardrail at the hoist, so nobody needed to tie off for most of the day. Harnesses are good, but a harness only works after you've already fallen. The guardrail means you never fall."
Common mistakes
MistakeThinking roofing is only about the roofing materials.
InsteadMost of the work, and most of the risk, is in setup, loading, weather, hot work and cleanup. Plan those as carefully as the roof itself.
MistakeAssuming that because roofer is a voluntary trade in Ontario, training does not matter.
InsteadSafety training such as Working at Heights is mandatory regardless of trade status, and the apprenticeship and Red Seal prove skill to employers and customers.
MistakeStaying quiet about a hazard because you are new.
InsteadNew workers are expected to ask and to report hazards. Supervisors would rather answer a question than file an injury report.
MistakeRelying on a harness as the first choice.
InsteadUse the hierarchy of controls: guardrails and other measures that keep people away from the edge come before personal fall protection.
Summary and key terms
- Roofers build, replace, repair and maintain the layers that keep weather out of buildings, including the metal flashings.
- The trade divides into low-slope commercial, steep-slope residential, sheet metal and flashing, and service and repair.
- In Ontario, Roofer (449A) is a voluntary Red Seal trade of about 4,000 hours with two in-school levels; the Certificate of Qualification is issued by Skilled Trades Ontario.
- O. Reg. 213/91 and the OHSA govern construction safety in Ontario, and Working at Heights training is required for workers who use fall protection.
- Workers have the right to know, to participate and to refuse or report unsafe work, and the duty to follow the rules and report hazards.
- A strong safety culture uses the hierarchy of controls and plans every job before anyone climbs.
- Low-slope roof
- A roof with a gentle slope that looks flat, covered by a continuous membrane; most commercial roofs are low-slope.
- Steep-slope roof
- A roof steep enough to shed water with overlapping materials such as shingles, metal, tile or slate.
- Tear-off
- Removing an existing roof covering down to the deck or to a sound layer before re-roofing.
- Flashing
- A piece of membrane or metal that seals a joint where the roof meets a wall, edge, curb or penetration.
- Registered apprenticeship
- A formal training agreement combining paid work hours with classroom training, recorded with the government apprenticeship authority.
- Toolbox talk
- A short safety meeting held at the start of a shift or task.
Practice problems
Work each problem on paper first, then reveal the answer to check.
Name the four main sectors of the roofing trade.
Show answer
Low-slope commercial, steep-slope residential, sheet metal and flashing, and service and repair.
What is the difference between re-roofing and recovering?
Show answer
Re-roofing removes the old roof first; recovering installs a new roof over the old one where allowed.
Which regulation contains Ontario's construction fall protection rules?
Show answer
O. Reg. 213/91 (Construction Projects) under the Occupational Health and Safety Act.
How many in-school levels does Ontario's roofer apprenticeship have?
Show answer
Two, of about 240 hours each (about 480 hours in school), within about 4,000 hours in total.
Name the three basic worker rights in Ontario.
Show answer
The right to know, the right to participate and the right to refuse unsafe work.
Lesson quiz · 5 questions
Score 60% or more to complete this lesson.
Create a free account to save your progress, take quizzes and earn a certificate.