PWR-340 · Lesson 12 of 12 · 28 min

Exam strategy for the third class certificate

▶ Video coming soon A video version of this lesson is on the way.

By the end of the code sessions, Okonkwo had a binder of his own: notes on each code family, a page of worked thickness and safety valve problems, the TSSA and ABSA material he had read, and a list of questions he had got wrong. His first Third Class paper, 3A-1, was planned for February 2027 and 3A-2 for the spring, with the Part B papers to follow. Grazyna spent the last session not on codes but on the exams themselves. "You know more than you think," she said. "The exam's job is to find out whether you can show it under time pressure. That is a skill too, and it can be practised."

PWR-240 and PWR-310 each ended with an exam lesson, at Fourth Class and for the science paper of Third Class. This lesson builds on them for the parts of the Third Class syllabus that this course covers: legislation and codes, code calculations, materials, welding and inspection, pressure vessels, piping, and plant safety management. It shows where these topics sit in the four papers, how to prepare for code questions and code calculations, how to manage time, and it closes with a set of mixed practice problems from the whole course.

Where this course fits

TSSA's Third Class certificate examination has four multiple-choice papers, 3A-1, 3A-2, 3B-1 and 3B-2, each of 150 questions in three and a half hours, with a pass mark of 65 in 100 on each paper. The SOPEEC syllabus that the papers follow spreads this course's topics across all four:

This course's topics in the Third Class papers (from the SOPEEC Third Class syllabus).
PaperSyllabus topics from this courseCourse lessons
3A-1Metallurgy and engineering materials; corrosion; industrial drawings including pressure vessel drawings3, 7
3A-2Industrial legislation and codes (power engineers regulations; ASME Sections I, IV, V, VI, VII and IX; CSA B51; CSA B52; NBIC); code calculations (Section I thickness and allowable pressure for tubes, drums and heads; safety valve sizing and capacity); piping; industrial safety and safety management1, 2, 5, 6, 8, 9, 10, 11
3B-1Boiler metals and construction; welding procedures and inspection (processes, preheat, PWHT, defects, NDE, Section IX qualification); pressure vessels (design, construction, repair regulations, nameplates, fittings and relief devices, testing, inspection)2, 3, 4, 5, 7
3B-2Plant maintenance and administration: preventive maintenance, records, operating procedures, training7, 9, 10, 11

The certificate requires all four papers. Each paper can be written separately, and a failed paper can be rewritten after 60 days. Okonkwo's qualifying experience for Third Class is already in place: more than 1,920 hours as a Fourth Class engineer at Cantwell, as PWR-310 described.

Preparing for code questions

Questions about codes and law test three things: knowing which document governs, knowing what it requires in broad terms, and recognizing the right answer among plausible wrong ones. They rarely test the exact wording of a paragraph. Grazyna's method for preparing:

  • Build a map of the documents. For each code and regulation, write one line on its scope and one on what it is used for. Lesson 1's family tree is the start.
  • Know the numbers that the exams like. Hydrostatic test multiples, accumulation limits, the conditions for two safety valves, inspection intervals, notification periods, the classes of certificate and the plants they may supervise, and the pass marks and experience rules themselves.
  • Learn the vocabulary exactly. Many wrong answers swap one term for another: accumulation for blowdown, design pressure for MAWP, repair for alteration, PQR for WPS, code case for interpretation.
  • Learn the reasons. A rule you understand is a rule you can reconstruct when the exact number escapes you: why the superheater valve is set lowest, why a hydrostatic test uses water, why the ligament governs a drum.
  • Read real documents. The nameplates in the plant, a data report, an inspection report, a welding procedure and its PQR, a relief valve repair tag. The exam's diagrams and descriptions come from documents like these.

Preparing for code calculations

Code calculation questions on 3A-2 ask for the required thickness or the maximum allowable pressure of tubes, drums and heads under Section I, and the required capacity, flow area or number of safety valves. The formulas are the code's, with its symbols and units, and they are part of what a candidate must learn to use; check the current examination guide for what formula sheets or reference material are provided. The teaching forms in this course explain where the code formulas come from and give a quick check on the size of an answer.

For every calculation, use the same five steps that PWR-310 set out: read the question for what is asked; list the given data with units; choose the formula; substitute with units, converting first; and check the answer for size and sense. For code calculations, add three code-specific checks:

  • Diameter: does the formula use the inside or outside diameter, or the radius? Tube formulas usually use the outside diameter, drum formulas often the inside.
  • Efficiency and allowances: has the ligament or joint efficiency been used, and have the allowances the question gives been added or subtracted in the right place?
  • Pressure basis: safety valve capacity uses absolute pressure with the overpressure added; thickness and allowable pressure use gauge pressure.

Managing time

A Third Class paper allows three and a half hours for 150 questions, an average of 1.4 minutes each. Most questions on law, codes and materials are recall or recognition and should take well under a minute, which banks time for the calculations. Grazyna's approach:

  • First pass: answer every question you know at once, and mark the calculations and the doubtful ones.
  • Second pass: work the calculations carefully, writing each step on the scratch paper so that a check is quick.
  • Third pass: return to the doubtful questions, eliminate the options you know are wrong, and choose among the rest.
  • Never leave a question blank. Multiple-choice papers do not usually penalize wrong answers, so an educated guess is better than nothing. Confirm the rule in the instructions.
  • Change an answer only for a reason, such as finding an error in the working, not on a feeling.

Worked problem

Time budget

A Third Class paper has 150 questions in 3.5 hours. Okonkwo expects 120 recall questions at about 45 seconds each and 30 calculations. How much time does that leave for each calculation, keeping 15 minutes at the end for review?

Show solution
  1. \[\text{recall} = 120 \times 0.75 = 90 \text{ min}\]
  2. \[\text{available} = 210 - 90 - 15 = 105 \text{ min}\]
  3. \[\text{per calculation} = \frac{105}{30} = 3.5 \text{ min}\]

Answer: Three and a half minutes is enough for a careful thickness or safety valve problem, but only if the recall questions really go quickly. Practising recall to speed is what makes time for the calculations.

Reading the options

Multiple-choice questions on codes and calculations are built with traps that recur:

  • The right number for the wrong rule: 1.3 times MAWP offered for a Section I boiler's hydrostatic test, or 10 in 100 accumulation for a power boiler.
  • The calculation with one step missing: a thickness without the corrosion allowance, a valve capacity calculated on gauge pressure, a stress without the ligament efficiency.
  • The swapped definition: blowdown described as accumulation, an interpretation described as a code case.
  • The answer that is true but does not answer the question: a correct statement about a different code or a different item.
  • Absolute words: options that say always or never are often wrong in codes, which are full of conditions and exceptions, but not always; read them carefully.

The best defence is to work the answer before looking at the options, then find it among them. If it is not there, the mistake is usually in the units or a missing step, and the distractors show which.

Mixed practice problems

These problems draw on the whole course. Work each one, then check the answer.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. A vessel shell has ID 900 mm, design pressure 1.2 MPa, S = 138 MPa, E = 1.0 and a corrosion allowance of 3 mm. Find the minimum thickness by the teaching form.

    Show answer

    1.2 × 900 ÷ 276 = 3.91 mm; plus 3 mm = 6.91 mm.

  2. A drum with ID 1,100 mm, S = 138 MPa and ligament efficiency 0.50 has 18 mm of plate. What pressure can it carry by the teaching form?

    Show answer

    2 × 138 × 0.5 × 18 ÷ 1,100 = 2.26 MPa.

  3. A safety valve set at 1,725 kPa has a flow area of 1,250 mm² and K = 0.8775. Find its capacity at 3 in 100 overpressure (atmosphere 101.3 kPa).

    Show answer

    P₁ = 1,878 kPa abs; W = 0.005252 × 0.8775 × 1,250 × 1,878 ≈ 10,800 kg/h.

  4. A Section VIII Division 1 vessel has an MAWP of 860 kPa. Typical hydrostatic test pressure?

    Show answer

    1.3 × 860 = 1,118 kPa, before temperature correction.

  5. A 75 m steam line heats from 15 °C to 170 °C (α = 12.0 × 10⁻⁶ per K). Growth?

    Show answer

    About 140 mm.

  6. Readings of 11.2 mm and 10.4 mm were taken 10 years apart; t_min is 8.0 mm. Remaining life and half-life interval?

    Show answer

    0.08 mm/yr; 30 years; 15 years, subject to the jurisdiction's maximum.

  7. A tube rated for 100,000 h at 560 °C runs at 575 °C. Expected life (Larson-Miller, C = 20)?

    Show answer

    About 36,100 h.

  8. An initiating event at 0.5 per year has IPLs with PFDs of 0.1 and 0.01. Mitigated frequency?

    Show answer

    5 × 10⁻⁴ per year.

  9. A boiler tube 63.5 mm OD at 4.1 MPa with S = 90 MPa. Pressure thickness by the teaching form?

    Show answer

    4.1 × 63.5 ÷ 180 = 1.45 mm.

  10. Which document records the test that qualified a welding procedure?

    Show answer

    The procedure qualification record.

  11. What is TSSA's maximum inspection interval for most pressure vessels under the 2025 amendment?

    Show answer

    Three years.

  12. Which NDE method would you choose for cracks in a stainless steel weld surface?

    Show answer

    Liquid penetrant testing.

Learning from the practice

Okonkwo's list of wrong answers was, Grazyna said, the most valuable page in his binder. For each wrong answer he wrote the question, his answer, the right answer and, most important, the reason he got it wrong: a missing step, a units slip, a confused term, a rule he had never learned. After a few weeks the reasons fell into a pattern. His were mostly units (kilopascals against megapascals) and forgetting to add atmospheric pressure in safety valve problems. Once he saw the pattern, he could guard against it with a habit: write the units on every number, and write "abs?" next to every pressure.

Grazyna's other advice was practical. Sleep before an exam, not study. Arrive early with the identification and calculator the rules allow. Read every question to the end; a final clause such as "which of the following is not" changes everything. And when the paper is done, write down what was hard while it is fresh, because that list is the study plan for the next paper.

After the certificate

A Third Class certificate opens the way to shift engineer posts in larger plants and to chief engineer posts in smaller ones, and it is a requirement for the Second Class papers. The knowledge in this course is also what the job needs every day: reading a nameplate before accepting a replacement part, checking a contractor's paperwork before a repair, knowing what a set point change needs before it is made, and asking the questions that find a problem early. "The exam is a gate," Grazyna said. "The habits are the career."

A study plan for the codes material

Okonkwo's study plan for the spring of 2027 gave this course's material its own weeks. With 3A-1 in February, he planned to spend the weeks before it on materials, metallurgy and corrosion alongside the science from PWR-310. For 3A-2 he planned a block on legislation and codes, a block on code calculations with at least forty worked problems, and a block on piping and safety management, with a full practice paper at the end of each block. The Part B material on welding, inspection and pressure vessels would come later, with the boiler material from PWR-330.

Okonkwo's study blocks for this course's material.
BlockContentPractice
1Codes and law: lessons 1 and 11; the Ontario regulations; the TSSA guideFlash cards of scopes, numbers and terms
2Design and relief calculations: lessons 2 and 5Forty worked problems with an error log
3Materials, welding and inspection: lessons 3, 4 and 7Nameplates, data reports and inspection reports read in the plant
4Piping and safety management: lessons 6, 8, 9 and 10One HAZOP node and one investigation written up
5ReviewFull practice paper under exam timing

He kept two rules. The first was to study a little most days rather than a lot on a few, because night shifts made long sessions hard and short ones stuck better. The second was to finish each session by writing three questions he could now answer and one he could not, so that the next session started where the last one had left off.

Using the plant as a textbook

The best study material was around him on every shift. He read the nameplate of every boiler, vessel and relief valve on his rounds and checked what each line meant. He traced the boiler external piping on the P&ID and then in the plant, valve by valve. He asked Fenella to show him a welding procedure and its PQR from the last repair, and Ottoline, on her next visit, to explain what she looked for inside a drum. He followed the deaerator change through its MOC, and the boiler 3 investigation to its recommendations. Each of these turned a page of notes into something he had seen and could describe, which is what a good examination answer, and a good shift engineer, needs.

"The candidates who struggle with the codes are the ones who have only read about them," Grazyna said. "You work in a building full of them. Use it."

Common mistakes

  • MistakeMemorizing code numbers without the reasons behind them.

    InsteadLearn the reason; it lets you rebuild a rule you have half forgotten.

  • MistakeCalculating safety valve capacity on gauge pressure.

    InsteadUse absolute pressure, with overpressure added.

  • MistakeLooking at the options before working a calculation.

    InsteadWork the answer first, then find it; distractors are built from common errors.

  • MistakeLeaving questions blank.

    InsteadAnswer every question unless the rules penalize guesses.

  • MistakeStudying the night before instead of sleeping.

    InsteadRest; tired candidates misread questions.

  • MistakeTreating a list of wrong answers as failure.

    InsteadIt is the best study guide; record the reason for each error.

Summary and key terms

  • The Third Class certificate requires four papers of 150 questions in 3.5 hours each, with 65 in 100 to pass each.
  • This course's topics appear across all four papers: materials on 3A-1; legislation, codes, code calculations, piping and safety management on 3A-2; welding, inspection and pressure vessels on 3B-1; maintenance and administration on 3B-2.
  • Prepare for code questions with a map of documents, the key numbers, exact vocabulary and the reasons behind rules.
  • For code calculations, check the diameter basis, efficiencies and allowances, and gauge or absolute pressure.
  • Budget time so recall questions bank minutes for calculations; work answers before reading options.
  • A record of wrong answers and their reasons is the most useful study tool.
Distractor
A wrong option in a multiple-choice question, often built from a common error.
Recall question
A question that tests knowledge of a fact, rule or definition.
Code calculation
A calculation of thickness, allowable pressure or relief capacity using a code's formulas.
Gauge pressure
Pressure measured above atmospheric pressure.
Absolute pressure
Pressure measured above a perfect vacuum.
Error log
A record of wrong answers with the reason for each error.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz