IRW-110 · Lesson 6 of 12 · 21 min

Fall protection for connectors and decking crews

▶ Video coming soon A video version of this lesson is on the way.

Grace's first Tuesday toolbox talk after Shay started, on September 22, was about one thing: falls. She drew the Ashcroft frame on the whiteboard, three tiers of steel with floors about 4.3 m apart, and marked where the connectors stood, where the decking crew would spread the deck, and where the open edges were. "Falls from height kill more ironworkers than anything else," she said. "Not cranes, not collapses. Falls. Every one of you has a harness. The question is what you tie it to, when, and what happens if you actually fall." This lesson covers the rules for fall protection on steel erection and the methods used to protect connectors and decking crews. The next lesson covers the equipment in detail.

Why falls are different on steel

On most construction sites, fall protection means guardrails around floor edges and openings, covers over holes, and harnesses for the jobs where guardrails cannot be used. Steel erection is harder. Until the steel is up, there are no floors to put guardrails on. Connectors stand on the top flange of a beam 150 to 300 mm wide, or climb columns, to make connections. Decking crews work at a leading edge that moves forward with every sheet they lay. Anchor points above the worker are few, because the worker is usually at the highest level of steel. And the structure itself is not yet stable.

For all those reasons, fall protection on steel erection is planned before the steel arrives. The erection plan shows where workers will be, how each will be protected, where anchors and lifelines will go, and how a fallen worker will be rescued. The planning starts with a simple order of preference, often called the hierarchy of fall protection.

The hierarchy of fall protection

The best protection removes the fall hazard; the weakest relies on the worker doing everything right. In order of preference:

  • Eliminate the hazard: assemble pieces on the ground and lift them as a unit, plan connections that can be made from a lift or from below, install perimeter cables or guardrails on members before they are raised.
  • Prevent the fall with passive protection: guardrails, perimeter safety cables, covers over openings and safety nets, which protect everyone without the worker doing anything.
  • Restrain the worker: a travel restraint system that keeps the worker from reaching an edge.
  • Arrest the fall: a personal fall arrest system with a full body harness, connector and anchor, which stops a fall after it starts.
  • Control the work: controlled access zones, warning lines and safety monitors, used only where the rules allow and the other methods are not practical.
A stepped pyramid with five levels, most effective at the top: eliminate the hazard, passive protection such as guardrails and nets, travel restraint, fall arrest, and administrative controls such as controlled zones. An arrow beside it shows that dependence on the worker increases toward the bottom.
The hierarchy of fall protection: use the highest level that is practical.

When fall protection is required

In Ontario, O. Reg. 213/91 requires fall protection where a worker could fall more than 3 m, and also at lower heights in particular cases: where a worker could fall into operating machinery, into water or another liquid, onto a hazardous substance or object, or through an opening in a work surface. The regulation sets the order: a guardrail system is the first choice, and only where a guardrail is not practical may the employer use, in order, a travel restraint system, a fall restricting system, a fall arrest system or a safety net. The Ontario regulation does not contain the special allowances for connectors and decking zones that the US federal steel erection rule has, so on an Ontario steel job the 3 m rule applies to everyone, connectors included.

Crossbeam's own rule on every job is stricter than the minimum: 100 in 100 tie-off above 1.8 m wherever a guardrail is not in place, and no work at an unprotected edge without a plan. Many steel erectors use a similar rule.

Connectors

Connectors work at the top of the steel, guiding beams onto columns and making the first bolted connections. Their work is the hardest to protect, because they must move along beams and climb columns while loads swing nearby, and because the best anchor points are often the member they are connecting.

On an Ontario job, connectors above 3 m must be protected like everyone else, usually by a fall arrest system anchored to the steel. Common methods are beam clamps or beam straps on a member already bolted, self-retracting lifelines mounted on columns, horizontal lifelines installed on the beams before they are lifted, and connecting from aerial lifts where the ground allows. Connectors need training in connecting procedures as well as working at heights training, and the employer's erection procedures must show how they will be protected at each stage.

Good practice for connectors includes:

  • Tie off before stepping onto the member and stay tied off while moving, using a twin-leg lanyard or two connectors so that one is always attached.
  • Never ride the load or stand on a beam that is not yet bolted at both ends.
  • Stay out from under the load and out of its path; guide it with tag lines until it is close enough to reach safely.
  • Make at least the minimum required bolts at each end, tightened by hand, before the crane releases the load.
  • Climb columns using the column ladder, the attached climbing features or an aerial lift, with fall protection, never by shinnying.

Decking crews

Once a tier of beams is connected and bolted, the decking crew spreads bundles of metal deck across the beams and fastens it down. The leading edge, where the next sheet will go, moves forward as they work. Behind them, the deck is the floor; ahead of them is open steel.

In Ontario, decking crews above 3 m must be protected by guardrails, travel restraint or fall arrest, and a common approach is a horizontal lifeline or a set of anchors installed along the beams, with workers using self-retracting lifelines rated for leading-edge use (lesson 7). Perimeter cables or guardrails go up at the outside edges of each floor as soon as the deck is down.

A plan of a floor bay being decked. Laid and fastened deck is behind the crew; open beams are ahead. The leading edge is marked. A horizontal lifeline runs along a beam with two workers connected to it by self-retracting lifelines. Perimeter cables are shown along the finished outside edge.
Decking at a leading edge with a horizontal lifeline and perimeter cables.

Deck is slippery when wet, frosty or oily, and sheets act like sails in wind. Deck bundles must be landed on beams strong enough to carry them, near a column or as the erection drawings show, and must not be broken open until the bundle is secured, because loose sheets blow off. Openings in the finished deck are covered or guarded right away and marked.

Other workers on steel

Bolt-up crews, welders and detailers follow the raising gang. They work on beams that are already connected, often from aerial lifts, floats or scaffolds, and sometimes on deck that is in place but has openings. Each needs fall protection as the height and the rules require. A worker who walks a beam to reach a connection is exposed exactly like a connector and must be tied off the same way.

Worked problem

Which rule applies?

At Ashcroft, the second-floor beams are 4.3 m above the slab on grade, the third-floor beams 8.5 m and the roof beams 12.8 m. Shay is helping bolt from a boom lift at the second floor; Andy is connecting roof beams; Nate's crew is decking the third floor. What does the Ontario regulation require for each, and what does Crossbeam add?

Show solution
  1. Shay at 4.3 m: above 3 m, so fall protection is required; in a boom lift that means a harness and lanyard attached to the platform anchor.
  2. Andy at 12.8 m: above 3 m; a fall arrest system anchored to bolted steel, with 100 in 100 tie-off.
  3. Nate at 8.5 m: above 3 m; deckers tied off to a horizontal lifeline or anchors with leading-edge SRLs.
  4. Crossbeam: the same for all three, plus its 1.8 m rule wherever guardrails are missing.

Answer: Everyone above 3 m is protected, with no exceptions for connectors or deckers.

Training

Every worker on an Ontario construction project who may use a travel restraint, fall restricting or fall arrest system or a safety net must have completed a working at heights training program approved by the Chief Prevention Officer, delivered by an approved provider, and must refresh it every three years. The employer must also train workers on the specific equipment and procedures used on the job. Shay completed both modules of an approved program on September 8 and 9, 2026, so his training is valid until September 2029.

Training is not a one-time event. At Crossbeam, every new job starts with a site-specific orientation that walks through the fall protection plan, the anchors and the rescue procedure, and the Tuesday toolbox talks return to falls every few weeks.

Planning fall protection for a job

At Crossbeam, every erection job has a written fall protection plan, prepared before the steel is delivered and reviewed with the crew at the site orientation. The Ashcroft plan was eight pages and a set of marked-up erection drawings. It showed, for each stage of erection:

  • Where workers would be exposed to falls: column tops, beam lines, the leading edge of the deck, the perimeter and openings.
  • The protection for each: column-mounted SRLs fixed on the ground before each column was lifted, beam clamps on bolted beams, a horizontal lifeline along each girder line for the decking crew, boom lifts for bolt-up, and perimeter cables installed on each floor as soon as the deck was down.
  • The anchors to be used and their ratings, and the engineered drawings for the horizontal lifelines.
  • The clearance at each level and the connecting devices that would work there.
  • The rescue method and equipment for each location (lesson 11).
  • Who was responsible for installing, inspecting and removing each part, and when.

The plan was a living document. When the third-floor east side turned out to be beyond the reach of the boom lift because a utility trench had been opened, Carla changed the bolt-up method there to beam clamps and SRLs, changed the rescue method to the rescue kit, and briefed the crew before the work started.

Perimeter cables and guardrails

Perimeter cables are wire ropes strung around the edge of each floor, usually at the top rail and mid-rail heights of a guardrail, through holes or brackets in the columns. They protect the crews that follow the raising gang: the decking, detailing and bolt-up crews, then the other trades. Perimeter cables must be tensioned so they do not deflect too far when pushed, attached to columns strong enough to hold them, flagged for visibility, and inspected regularly. They are removed only when the permanent walls or guardrails replace them, and if they are taken down for a delivery or for the curtain wall installer, the opening is protected by other means before work continues there.

Guardrails on Ontario projects must meet the regulation's requirements for height, strength and the size of openings, and perimeter cables used as guardrails must be designed to meet those requirements.

Covers and openings

Holes in the deck for stairs, shafts, ducts and plumbing are left by design, and holes are made later by other trades. Every hole a worker could fall through, or step into, must be covered or guarded. Covers must be strong enough for the loads that may cross them, secured so they cannot slide or be kicked off, and marked with a word such as HOLE or COVER. Never remove a cover without permission, and never leave a hole uncovered when you walk away, even for a minute.

Fall protection and the other trades

When Crossbeam finished each floor, the perimeter cables, covers and any horizontal lifelines left in place became the protection for everyone who followed. Equipment left for other trades must be inspected and accepted by the general contractor, who takes responsibility for it, and nobody may remove or alter it without permission. At Ashcroft, Priscilla Hahn walked each floor with Carla before Tallcorn accepted the perimeter cables, and any cable taken down for a delivery was put back, or the edge protected another way, before the area was reopened.

Common mistakes

  • MistakeTreating a harness as the first choice.

    InsteadUse the hierarchy: eliminate the hazard and use passive protection first; fall arrest comes later.

  • MistakeWalking a beam untied to reach a connection.

    InsteadAnyone on a beam is exposed like a connector and must be tied off.

  • MistakeBreaking open a deck bundle before it is secured.

    InsteadSecure bundles before opening them; loose sheets blow off and fall.

  • MistakeAssuming the federal minimum is the rule on site.

    InsteadFollow the site and employer rules, which are often stricter.

  • MistakeReleasing a beam before the minimum bolts are in.

    InsteadInstall the required bolts at each end before the crane lets go.

  • MistakeLeaving an opening in new deck unmarked.

    InsteadCover or guard every opening at once and mark it.

Summary and key terms

  • Falls are the leading cause of death in ironwork; fall protection is planned before the steel arrives.
  • The hierarchy: eliminate, passive protection, travel restraint, fall arrest, and administrative controls last.
  • In Ontario, fall protection is required above 3 m and in other listed cases, with guardrails first; there is no connector or decking-zone exception.
  • Connectors and deckers use beam clamps, column-mounted SRLs, horizontal lifelines, aerial lifts and leading-edge SRLs.
  • Perimeter cables or guardrails go up as soon as the deck is down; openings are covered at once.
  • Working at heights training must be renewed every three years.
Hierarchy of fall protection
The order of preference for protecting workers from falls, from eliminating the hazard to administrative controls.
Travel restraint system
A system that keeps a worker from reaching an edge where a fall could happen.
Fall arrest system
A system that stops a worker after a fall has started.
Leading edge
The edge of a floor or deck that moves forward as work progresses.
Perimeter safety cable
Wire rope strung around the edge of a floor to act as a guardrail.
Anchor point
A secure point on the structure to which fall protection is attached.
Horizontal lifeline
A cable or rail between anchors that workers attach to and move along.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. At what height does Ontario's construction regulation require fall protection in most cases?

    Show answer

    More than 3 m.

  2. What is the first choice of fall protection under the Ontario regulation?

    Show answer

    A guardrail system.

  3. Does the Ontario regulation have a special allowance for connectors?

    Show answer

    No; the 3 m rule applies to them too.

  4. How often must Ontario working at heights training be refreshed?

    Show answer

    Every three years.

  5. Name two ways to protect a connector.

    Show answer

    Beam clamp or strap on bolted steel; column-mounted SRL; horizontal lifeline on beams; connecting from an aerial lift.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz