IRW-110 · Lesson 5 of 12 · 23 min

Personal protective equipment

▶ Video coming soon A video version of this lesson is on the way.

At the kit issue on his first morning, Grace handed Shay a hard hat with a chin strap, safety glasses, a face shield, earplugs and earmuffs, two kinds of gloves, a high-visibility vest, a full body harness with a shock-absorbing lanyard, and a voucher for boots. "The harness gets a whole lesson of its own," she said. "Today we fit the rest." Personal protective equipment, or PPE, is the last line of defence. It does not remove a hazard; it reduces the harm if the hazard reaches you. On a steel job, where some hazards cannot be engineered away, PPE matters a great deal. The general safety course (TRD-101) covered choosing, fitting and caring for PPE; this lesson is about the PPE an ironworker needs and why.

Head protection

Hard hats on Ontario construction projects must meet the regulation's requirements, and in practice that means a hat certified to CSA Z94.1. CSA classifies hats by the kind of impact they protect against, Type 1 for the top only and Type 2 for the top and sides, and by electrical class, with Class E for high-voltage protection and Class G for general use. Ironworkers are struck from the side as often as from above, by swinging loads, beam ends and tools, so many contractors, Crossbeam among them, now issue Type 2 hats.

At height, a hard hat must stay on in a fall or when a worker bends over an edge, so ironworkers wear a chin strap. Crossbeam requires chin straps above the ground floor. A hat that falls off is a falling object and leaves the worker unprotected. Replace a hard hat after any significant impact, if the shell is cracked, faded, brittle or chalky, or when the maker's service life is reached; the suspension usually needs replacing more often. Do not paint shells, drill them or store them on the rear window of a truck in the sun.

A front view of an ironworker in PPE, with labels: hard hat with chin strap, safety glasses and face shield for grinding, hearing protection, high-visibility vest or shirt, cut-resistant gloves, full body harness, tool belt separate from the harness, and safety boots with protective toes and puncture-resistant soles.
PPE for an ironworker on steel.

Eye and face protection

Eye protection is worn at all times on site. Safety glasses must meet CSA Z94.3, with side protection. Grinding, chipping and cutting add a face shield over the glasses, and cutting and welding need filter lenses or helmets with the right shade for the process. Tinted glasses help in bright sun but must not be worn indoors or at dusk, when they cut visibility on steel.

Shade numbers rise with the brightness of the process. Typical ranges are about shade 3 to 6 for oxy-fuel cutting, depending on plate thickness, and about 10 to 13 for arc welding and plasma cutting, depending on current; the welding courses give the full table. Anyone near the work needs protection from the arc's ultraviolet light too, and welding screens keep it from reaching people nearby.

Hearing protection

Steel jobs are loud. Impact wrenches, grinders, air arcs, cranes, generators and steel banging on steel all exceed the level at which hearing is damaged over time. Hearing loss from noise is permanent, painless and gradual; most workers do not notice it until it is too late.

In Ontario, O. Reg. 381/15 sets the noise limit for workplaces, including construction: an exposure of 85 dBA averaged over 8 hours, with a 3 dB exchange rate. Every increase of 3 dB halves the time allowed. Employers must first try to reduce noise at the source; where they cannot, workers must wear hearing protection chosen for the noise level.

Worked problem

How long at the grinder?

Nate's grinder measures 97 dBA at the operator's ear. Under the Ontario limit of 85 dBA for 8 hours with a 3 dB exchange rate, how long may a worker be exposed without hearing protection?

Show solution
  1. Increase above the limit: 97 − 85 = 12 dB.
  2. Number of halvings: 12 ÷ 3 = 4.
  3. Time allowed: 8 ÷ 2⁴ = 8 ÷ 16 = 0.5 hours.

Answer: Only 30 minutes in a whole shift. Anyone grinding for more than a few minutes needs hearing protection, and so do people working close by.

Earplugs must be inserted correctly to work: rolled, inserted deep with the ear pulled up and back, and held until they expand. Earmuffs must seal against the head; safety glasses arms and long hair break the seal. On steel, workers must still hear signals and warnings, so communication is planned: radios with headsets, agreed hand signals, and a horn or whistle code for the crane.

Hand protection

Steel edges, burrs, wire rope, rebar ends and sheet deck cut hands every day. Ironworkers wear cut-resistant gloves for handling steel and deck, leather gloves for rigging and hot work, and insulated gloves in cold weather. Cut resistance is rated on a scale; in North America the ANSI/ISEA 105 scale runs from A1, the lowest, to A9, the highest, and many contractors require A4 or higher for handling sheet deck and sharp steel. Gloves must fit; a loose glove can be caught by a rotating drill or pulled into a pinch point.

  • Never wear gloves near a rotating drill bit or chuck; they can be caught and wrap the hand in.
  • Use leather or heat-resistant gloves for cutting and welding; synthetic gloves can melt into skin.
  • Keep hands out of pinch points: between a load and the steel, between a sling and a load, and in bolt holes while pieces are moving.

Foot protection

Safety footwear on Ontario construction projects must meet CSA Z195 and be Grade 1, marked with a green triangle patch for toe protection and puncture-resistant soles. Many ironworkers choose boots with ankle support and soles that grip steel; a smooth sole is slippery on wet or frosty beams. Crossbeam requires electrical shock-resistance (the white rectangle with an orange omega) on jobs near energized equipment.

Many ironworkers prefer boots with a defined heel when walking beams and climbing, and soft, flexible soles for feeling the steel, but footwear must still meet the standard. Keep soles clean of mud, ice and oil before climbing; a muddy sole on steel is like a skate.

Visibility and clothing

High-visibility apparel must meet CSA Z96, with the class and colour the site requires; on most construction projects that is a vest or shirt with fluorescent background and retroreflective stripes. Crane operators and equipment drivers must be able to see every worker, especially on the ground among moving loads and trucks.

Clothing should be close-fitting, without loose ends that catch on steel, and made of natural fibres or flame-resistant fabric for hot work, because synthetics melt. Ironworkers work in all weather, so layers matter: base layers that move sweat away from the body, an insulating layer, and a wind and rain shell. Heat and cold both affect judgement and grip. In hot weather, drink water often and take breaks in the shade; in cold weather, watch for numb fingers and toes and for a coworker who becomes confused or clumsy.

Respiratory protection

Cutting, welding and grinding steel produce fumes and dust. Galvanized steel gives off zinc oxide fume when cut or welded, which can cause metal fume fever, a flu-like illness. Painted steel may carry lead or other metals in old coatings, especially on bridges and older buildings. Welding fume contains manganese and other metals. The first defence is to work outdoors or with good ventilation and to stay out of the plume; where that is not enough, a respirator chosen for the hazard and fitted by a fit test is needed. Respirators are covered in the welding courses and the hazardous materials material in TRD-101.

Caring for PPE

PPE works only if it is in good condition and worn correctly. Inspect it before every shift, clean it as the maker says, store it out of the sun and away from chemicals and sparks, and replace it when it is damaged or worn out. Report damaged PPE; the employer must replace it. Shay's kit check each morning took two minutes: hat and strap, glasses, hearing protection, gloves, vest, boots and, separately and carefully, the harness and lanyard.

PPE in hot and cold weather

Ironworkers wear the same PPE in a heat wave as in a January wind, and both make it harder. In heat, hard hats, harnesses and long sleeves trap heat, and sweat makes gloves slippery and glasses fog. Crossbeam's heat plan has water and shade at every work level, more frequent breaks as the temperature and humidity rise, earlier start times in summer, and a buddy system so that workers watch each other for signs of heat illness: heavy sweating or no sweating, headache, dizziness, nausea, confusion and clumsiness. Heat stroke is a medical emergency; call for help and cool the worker at once.

In cold weather, the danger is numb hands and feet, stiff muscles and slowed reactions. Hard hat liners that fit under the hat without lifting it off the suspension, insulated gloves that still let a worker grip a wrench, and boots with insulation and good soles all help. Frostbite shows first as white or grey, waxy, numb skin; hypothermia shows as shivering, then confusion, slurred speech and clumsiness. Wind makes cold much worse, and the steel itself pulls heat out of hands and knees.

PPE does not replace planning

Every piece of PPE in this lesson is the last line of defence. A hard hat does not make it acceptable to work under connectors; it protects against the bolt that falls despite the controlled zone. A face shield does not make it acceptable to stand in line with a grinder wheel; it protects against the fragment that leaves despite the guard. Hearing protection does not make a noisy job quiet; quieter tools and keeping people away from the noise come first. Each time Grace introduced a piece of PPE, she asked the same question first: what could we do so that we do not need it?

Who pays, who decides

Under Ontario's Occupational Health and Safety Act and its construction regulation, employers must provide or make sure workers have the protective equipment the work requires, and must train workers to use it; workers must wear and use the equipment their employer requires. Some items, such as safety boots, are often supplied by the worker under the collective agreement or employer policy, sometimes with an allowance. Crossbeam gives each new apprentice a boot voucher and replaces worn harnesses, hard hats and gloves at no cost.

Workers have a say too. A worker who is issued PPE that does not fit, is damaged or is not right for the hazard should report it to the foreperson or the safety coordinator and get it replaced before starting work. Shay's first pair of gloves was too large for his hands, and he was issued a smaller size the same morning. A glove that is too big is not just uncomfortable; it reduces grip and can be caught.

Worked problem

Glove choice by task

Shay has three pairs of gloves in his bag: cut-resistant knit gloves rated A4, leather rigger's gloves and leather welding gauntlets. Which should he wear for each task: carrying sheet deck, handling wire rope slings, holding a torch to cut a clip, and running a magnetic drill?

Show solution
  1. Sheet deck: the A4 cut-resistant gloves, because deck edges are sharp.
  2. Wire rope slings: leather rigger's gloves, which resist broken wires and abrasion.
  3. Cutting with a torch: leather welding gauntlets, which resist heat and spatter.
  4. Magnetic drill: no gloves near the rotating cutter; keep hands clear and use a brush or hook for chips.

Answer: Different tasks need different gloves, and one task needs none. Carrying the right gloves for the day is part of planning the work.

A daily PPE routine

Shay's two-minute check each morning followed the same order, top to bottom, so nothing was missed: hard hat shell and suspension, chin strap, safety glasses clean and unscratched, face shield if grinding was planned, earplugs in his pocket and earmuffs on the hat, high-visibility vest clean and intact, the right gloves for the day's tasks, boots laced with soles clear of mud, and then the harness and lanyard on their own, checked strap by strap. Anything worn or damaged went to Grace before the toolbox talk, not after the first lift. A routine like that takes less time than finding a missing glove at the top of a column.

Common mistakes

  • MistakeWearing a hard hat without a chin strap at height.

    InsteadUse a chin strap above the ground floor so the hat stays on and does not become a falling object.

  • MistakeGrinding with only safety glasses.

    InsteadAdd a face shield over the glasses for grinding, chipping and cutting.

  • MistakePushing earplugs halfway in.

    InsteadRoll, insert deep with the ear pulled up and back, and hold until they expand.

  • MistakeWearing gloves at a drill press or mag drill.

    InsteadKeep gloved hands away from rotating bits and chucks.

  • MistakeCutting steel in synthetic clothing.

    InsteadWear natural fibres or flame-resistant clothing for hot work.

  • MistakeKeeping a cracked or chalky hard hat.

    InsteadReplace hats after impact, when damaged or at the maker's service life.

Summary and key terms

  • Hard hats meet CSA Z94.1; Type 2 hats protect the top and sides, and chin straps keep them on at height.
  • Safety glasses are worn all the time, with face shields for grinding and filter lenses for cutting and welding.
  • Ontario's noise limit is 85 dBA for 8 hours with a 3 dB exchange rate.
  • Cut-resistant gloves protect against sharp steel; gloves stay away from rotating bits.
  • Safety boots, high-visibility clothing and flame-resistant clothing for hot work complete the kit.
  • Inspect PPE every shift and replace it when damaged.
PPE
Personal protective equipment: clothing and equipment worn to reduce harm from hazards.
Type 2 hard hat
A hard hat tested for impacts on the top and the sides.
Chin strap
A strap that keeps a hard hat on in a fall or when bending over.
Exchange rate
The increase in noise level that halves the allowed exposure time.
dBA
A sound level measured with a weighting that matches the response of the human ear.
Cut resistance
A glove rating for how well it resists being cut by a sharp edge.
Metal fume fever
A flu-like illness caused by breathing zinc oxide or other metal fume.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. Why do many ironworkers now wear Type 2 hard hats?

    Show answer

    They protect against side impacts from swinging loads, beam ends and tools.

  2. How long may a worker be exposed to 94 dBA under Ontario's limit?

    Show answer

    94 − 85 = 9 dB, 3 halvings: 8 ÷ 8 = 1 hour.

  3. Why should gloves not be worn at a rotating drill?

    Show answer

    They can be caught and pull the hand in.

  4. What marks a Grade 1 CSA Z195 safety boot?

    Show answer

    A green triangle patch.

  5. What illness can cutting galvanized steel cause?

    Show answer

    Metal fume fever.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz