APT-110 · Lesson 6 of 12 · 25 min

WHMIS and handling dangerous goods

▶ Video coming soon A video version of this lesson is on the way.

On Wednesday, September 16, 2026, Talia's third day, Imani took her through the dealership's WHMIS training in the morning and then spent the afternoon showing her where it applied in the parts department. The training covered the labels, the pictograms and the safety data sheets. The afternoon covered the products: a shelf of brake cleaner aerosols, cases of antifreeze and windshield washer fluid, brake fluid, engine oil and transmission fluid, battery acid in the battery cage, refrigerant cans, adhesives and sealers for the body shop, and a locked cabinet of flammable paint products. "Most of what we sell will hurt you if you use it wrong," Imani said. "The label and the SDS tell you how not to."

A parts department stores and sells far more hazardous products than most workplaces of its size. Workers handle them every day, and customers rely on the parts counter to sell them in safe containers with the right information. This lesson covers the system that tells workers about chemical hazards, how to read labels and safety data sheets, the basic rules for storing and handling hazardous products, what to do after a spill or exposure, and an introduction to the separate rules for shipping them. Lesson 7 then looks closely at batteries, fluids and other hazardous parts.

What WHMIS is

The Workplace Hazardous Materials Information System (WHMIS) is Canada's national system for communicating the hazards of chemicals and other hazardous products used at work. Its current form, WHMIS 2015, is aligned with the United Nations Globally Harmonized System of Classification and Labelling of Chemicals (GHS). Suppliers' duties are set by the federal Hazardous Products Act and the Hazardous Products Regulations, and employers' duties by each province; in Ontario, they are in the Occupational Health and Safety Act and its WHMIS regulation. Amendments to the federal regulations in 2022, aligning WHMIS with a newer revision of the GHS, finished their transition period on December 14, 2025.

WHMIS has three main parts: labels on hazardous products, safety data sheets (SDSs) that give detailed information about each product, and worker education and training. Under the Ontario rules, an employer must make sure every hazardous product in the workplace has a proper label and a current SDS, that SDSs are readily available to workers, and that workers are trained in the hazards of the products they work with and the procedures for using them safely. Workers must take part in the training and follow the procedures.

Consumer products sold to the public, such as a can of brake cleaner on a retail shelf, carry consumer labels under consumer product law. But when the same products are stored, handled and used in the workplace, the workplace rules still require workers to have the hazard information and training. A parts department is both a workplace and a store, so it deals with both kinds of label.

Pictograms and hazard classes

The GHS sorts hazards into physical hazards, such as flammable, explosive, oxidizing, gases under pressure and corrosive to metals, and health hazards, such as acute toxicity, skin corrosion, eye damage, sensitization, cancer, reproductive toxicity and organ damage. Each hazard class is shown on labels by a pictogram: a black symbol on a white background inside a red diamond border.

GHS pictograms and examples of products that carry them. WHMIS 2015 also uses a biohazard pictogram for infectious materials.
PictogramMain meaningExamples in a parts department
FlameFlammable liquids, gases, aerosols and solidsBrake cleaner, carburetor cleaner, paint, gasoline additives
CorrosionCorrosive to skin, eyes or metalsBattery acid, some rust removers and wheel cleaners
Gas cylinderGas under pressureRefrigerant cans, aerosol propellants, nitrogen cylinders
Exclamation markIrritant, harmful, sensitizer, narcotic effectsMany cleaners, some adhesives
Health hazardCancer, reproductive, organ or breathing hazardSome solvents, used engine oil, some sealers
Skull and crossbonesAcute toxicity: can kill in small amountsSome antifreeze concentrates, methanol washer fluid concentrate
Flame over circleOxidizerSome pool and cleaning chemicals
Exploding bombExplosive or self-reactiveSome airbag and pretensioner components, as shipped
EnvironmentHazardous to aquatic lifeMany oils and fuels
Nine red-bordered diamonds in a grid, each with a simple symbol and its name: flame, corrosion, gas cylinder, exclamation mark, health hazard, skull and crossbones, flame over circle, exploding bomb, and environment.
The GHS pictograms, drawn here in simplified form.

A product can carry several pictograms. Brake cleaner, for example, typically shows the flame (it is an extremely flammable aerosol), the gas cylinder or exclamation mark, and the health hazard pictogram if it contains solvents that harm the nervous system with repeated exposure.

Reading a supplier label

The label that comes on a hazardous product from its supplier must contain set information, arranged however the supplier chooses but always including:

  • Product identifier: the product name, matching the SDS.
  • Pictograms for each hazard class.
  • Signal word: "Danger" for the more severe hazards, "Warning" for the less severe.
  • Hazard statements: standard sentences describing the hazard, such as "Extremely flammable aerosol" or "Causes severe skin burns and eye damage".
  • Precautionary statements: standard sentences on prevention, response, storage and disposal, such as "Keep away from heat, sparks and open flames" or "Wear protective gloves and eye protection".
  • Supplier identifier: the name, address and phone number of the supplier.

WHMIS supplier labels must be in both English and French and must have a border, often a hatched one, around the label information.

A sample supplier label for a fictional brake cleaner aerosol, with each required element numbered: product identifier, pictograms, signal word, hazard statements, precautionary statements and supplier identifier.
The required elements of a supplier label, shown on a sample label for a fictional product.

When a product is moved into a different container in the workplace, such as windshield washer fluid poured from a drum into a jug, the new container needs a workplace label. A workplace label must give at least the product name, safe handling information and a reference to the SDS. Linmore Tessaro prints workplace labels from its SDS system, and Imani showed Talia how to make one for the shop's spray bottles of diluted wheel cleaner.

Worked problem

Decoding a label at the counter

A customer asks Talia whether a two-part body filler hardener is safe to keep in her garage beside the furnace. The hardener's label shows the flame and exclamation mark pictograms, the signal word "Warning", and the statements "Heating may cause a fire" and "Store away from combustible materials." What should Talia tell her?

Show solution
  1. The hardener is an **organic peroxide**. On this product the flame pictogram means it can catch fire or break down and release heat if it gets warm.
  2. The statement "Heating may cause a fire" means it must be kept cool.
  3. Beside a furnace is the wrong place: it is warm and near a source of ignition and combustible materials.

Answer: Talia told her to store the hardener in its closed container in a cool place away from the furnace, sunlight and other combustibles, and to read the storage section of the SDS, which she printed for her. She also suggested buying only as much as the job needed.

Safety data sheets

A safety data sheet gives much more detail than the label. Under the GHS format used on both sides of the border, every SDS has the same 16 sections in the same order, so workers can find the same information in any SDS:

The 16 sections of a GHS safety data sheet.
SectionContentsSectionContents
1Identification9Physical and chemical properties
2Hazard identification10Stability and reactivity
3Composition and ingredients11Toxicological information
4First-aid measures12Ecological information
5Firefighting measures13Disposal considerations
6Accidental release measures14Transport information
7Handling and storage15Regulatory information
8Exposure controls and personal protection16Other information, including the date of the last revision

For day-to-day work, the most useful sections are 2 (what the hazards are), 4 (first aid), 6 (what to do in a spill), 7 (how to handle and store it) and 8 (what protective equipment to wear). Linmore Tessaro keeps its SDSs in an online system with a terminal at each counter and a printed binder in the parts office in case the network is down.

Storing and handling hazardous products

The SDS and the label say how each product should be stored. General rules in the parts department include:

  • Keep flammable liquids and aerosols in approved flammable storage cabinets or a designated area away from heat, sparks and electrical equipment, and keep the quantity on the floor to what is needed.
  • Keep corrosives, such as battery acid, below eye level and away from flammables and metals, with secondary containment such as a tray or bund.
  • Keep oxidizers apart from flammables and combustible materials.
  • Store gas cylinders and pressurized cans upright, secured, and away from heat.
  • Store heavy liquids on low shelves, and never stack drums or pails higher than the manufacturer allows.
  • Keep containers closed when not in use, and check for leaks, dents and damaged labels during the daily walk.
  • Wear the protective equipment the SDS calls for: usually safety glasses and chemical-resistant gloves, and a face shield for pouring corrosives.

Spills and exposures

Every parts department needs a spill kit near where liquids are stored, with absorbent pads and granules, gloves, goggles, bags and a neutralizer for battery acid. For a small spill of a product the worker has been trained to clean up, the procedure is: warn others, put on protective equipment, stop the source if it is safe to do so, contain the spill with absorbent, clean it up, bag the waste and label it, and report it. A large spill, a spill of an unknown product, or a spill with strong vapours means evacuate the area and call for help.

If a chemical gets into someone's eyes, the first aid is to flush the eyes with clean water immediately and keep flushing for at least 15 minutes, holding the eyelids open, then get medical help. Corrosives such as battery acid need longer flushing, as the SDS advises. Linmore Tessaro has a plumbed eyewash station in the battery area and a portable one on the dock.

Worked problem

Sizing a portable eyewash

A common industry standard for emergency eyewash (ANSI Z358.1) calls for a flow of at least 1.5 L/min for 15 minutes. How much water must a self-contained portable eyewash hold?

Show solution
  1. Water needed:
  2. \[1.5 \times 15 = 22.5\ \text{L}\]

Answer: The unit must deliver at least 22.5 L. A small squeeze bottle is only for an immediate rinse on the way to a proper eyewash, never a substitute for one. The dock's portable unit is checked monthly and its water or additive changed on the maker's schedule.

Shipping dangerous goods: an introduction

WHMIS covers hazardous products in the workplace. When the same products are transported, a different set of rules applies: the federal Transportation of Dangerous Goods (TDG) Act and Regulations. TDG classifies dangerous goods into nine classes, requires safety marks such as placards and labels on packages and vehicles, sets out shipping documents, and requires that anyone who handles, offers for transport or transports dangerous goods be trained and hold a training certificate from the employer. For road transport, the certificate is valid for 36 months. Many parts shipments, such as small aerosols and automotive fluids, qualify for limited quantity or consumer-commodity relief, but someone still has to know the rules to know when the relief applies. Gideon and Sasha hold TDG training certificates; Talia will be trained before she ships anything. APT-220 covers shipping in detail.

Selling hazardous products to the public

A parts counter sells hazardous products to the public every day, and the counter staff are often the last people to talk to the customer before the product is used. Good practice at the counter includes:

  • Selling products only in their original, labelled containers, never decanted into unmarked jugs or bottles.
  • Pointing out the main hazard on the label when a customer seems unfamiliar with a product, such as the flammability of brake cleaner or the toxicity of coolant to pets.
  • Printing the safety data sheet for a trade customer who asks for it, as professional shops often need it for their own workplace records.
  • Bagging corrosive and flammable products separately from food or clothing a customer may also be carrying.
  • Refusing to sell a product in a damaged or leaking container, and setting it aside for return.

Talia found that most customers welcomed a short, practical comment. When a customer bought a jug of concentrated washer fluid on a cold October afternoon, she mentioned that the concentrate is poisonous and should be stored where children cannot reach it, and the customer thanked her: she had young children and had not thought about it.

Worked problem

Checking a flammables cabinet's capacity

The flammables cabinet behind the front counter is rated for 114 L of flammable liquids. Its shelves hold 36 cans of carburettor cleaner of 0.4 L each and 24 bottles of a fuel additive of 0.35 L each. How much of the cabinet's rated capacity is used?

Show solution
  1. Carburettor cleaner:
  2. \[36 \times 0.4 = 14.4\ \text{L}\]
  3. Fuel additive:
  4. \[24 \times 0.35 = 8.4\ \text{L}\]
  5. Total:
  6. \[14.4 + 8.4 = 22.8\ \text{L}\]
  7. Share of capacity:
  8. \[22.8 \div 114 = 0.20\]

Answer: About 22.8 L, or 20 in 100 of the cabinet's rating, so there is plenty of room. The fire code and the cabinet's label set the limits; aerosols are counted under their own rules.

Common mistakes

  • MistakePouring a product into an unmarked spray bottle.

    InsteadPut a workplace label with the product name, safe handling information and SDS reference on every secondary container.

  • MistakeReading only the product name on a label.

    InsteadRead the pictograms, signal word and hazard and precautionary statements too.

  • MistakeStoring battery acid on a top shelf beside aerosols.

    InsteadKeep corrosives low, contained and away from flammables and metals.

  • MistakeRinsing an eye splash for a few seconds and going back to work.

    InsteadFlush for at least 15 minutes, longer for corrosives, and get medical help.

  • MistakeAssuming workplace hazard training also covers shipping.

    InsteadShipping dangerous goods needs separate training under the transport rules.

Summary and key terms

  • WHMIS 2015, aligned with the GHS, communicates hazards through labels, safety data sheets and worker training.
  • Pictograms in red diamonds show hazard classes such as flammable, corrosive, gas under pressure, toxic and health hazard.
  • Supplier labels give the product identifier, pictograms, signal word, hazard and precautionary statements and supplier identifier.
  • Secondary containers in the workplace need a workplace label.
  • Safety data sheets have 16 standard sections; sections 2, 4, 6, 7 and 8 matter most day to day.
  • Flammables, corrosives, oxidizers and pressurized containers are stored apart with the right cabinets and containment.
  • Small spills are contained and cleaned with a spill kit; eye exposures are flushed for at least 15 minutes.
  • Transporting dangerous goods falls under TDG, which requires training certificates.
WHMIS
Workplace Hazardous Materials Information System, Canada's system for communicating chemical hazards at work.
GHS
The Globally Harmonized System of Classification and Labelling of Chemicals.
Pictogram
A symbol in a red diamond border showing a hazard class on a label.
Signal word
"Danger" or "Warning", showing the relative severity of a hazard.
Safety data sheet
A 16-section document giving detailed hazard, handling, first-aid and emergency information for a product.
Workplace label
A simplified label for a product transferred to another container in the workplace.
Limited quantity
A small amount of a dangerous good in a package that qualifies for reduced shipping requirements.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. Name the six elements of a supplier label.

    Show answer

    Product identifier, pictograms, signal word, hazard statements, precautionary statements and supplier identifier.

  2. Which SDS section tells you what protective equipment to wear?

    Show answer

    Section 8, exposure controls and personal protection.

  3. What does the flame-over-circle pictogram mean?

    Show answer

    An oxidizer, which can start or feed a fire.

  4. How much water must a portable eyewash deliver to meet a 1.5 L/min flow for 15 minutes?

    Show answer

    22.5 L.

  5. What must be on a workplace label?

    Show answer

    The product name, safe handling information and a reference to the SDS.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz