IRW-130 · Lesson 2 of 12 · 26 min

Bar sizes, grades and markings

▶ Video coming soon A video version of this lesson is on the way.

At the second rod school night, on Monday, October 5, Tobias had a rack of bar ends waiting on the shop bench, each cut about a hand's length long and each a different size. He asked Shay and the two other new apprentices to sort them from smallest to largest and name each one. They had the order right in a minute. Naming them took longer. Two bars that looked almost identical turned out to be one size apart, and a bar Shay was sure was the largest on the bench was a size smaller than the one beside it. "You will never measure a bar with a tape on the job," Tobias said. "You will read the tag, read the marks on the bar and know the size by eye and by weight. Get it wrong, and the wall has the wrong steel in it, and nobody will find out until it cracks."

This lesson covers how reinforcing bars are sized and named, the steel grades in common use, how bars are marked at the mill, how bundles are tagged and how to work out the weight of bars and bundles. It is the vocabulary that every placing drawing and bar list in the rest of the course is written in.

How bars are named

In the United States, reinforcing bars are made to ASTM standards, mainly ASTM A615 for carbon steel bars and ASTM A706 for low-alloy bars that can be welded, and are named by number: #3, #4, #5 and so on up to #11, then #14 and #18. For bars #3 to #8, the number is the nominal diameter in eighths of an inch: a #4 bar is 4/8 or 1/2 in, and a #8 bar is 8/8 or 1 in. Bars #9 to #18 are sized to give round cross-sectional areas instead, so their diameters are not exact eighths. Mills also roll the same bars in soft metric sizes, marked #10, #13, #16 and so on, that are physically the same as the inch-pound bars; a #16 metric bar is a #5. Drawings on a US job will use one system throughout.

A bar's nominal diameter is the diameter of a plain round bar with the same weight per length. Because of the deformations, the outside of a bar measured over the ribs is larger than its nominal diameter, which is one reason measuring a bar with calipers or a tape is unreliable.

US inch-pound bar sizes under ASTM A615 and A706. Weights are nominal.
Bar sizeNominal diameter (in)Area (in²)Weight (lb/ft)
#30.3750.110.376
#40.5000.200.668
#50.6250.311.043
#60.7500.441.502
#70.8750.602.044
#81.0000.792.670
#91.1281.003.400
#101.2701.274.303
#111.4101.565.313
#141.6932.257.650
#182.2574.0013.600
Cross-sections of the common bar sizes drawn to the same scale side by side, from the smallest to the largest, each labeled with its size, nominal diameter and mass or weight per length. A note points out that each size step adds more area than the last, and that the two smallest sizes look most alike.
The common bar sizes drawn to scale.

The weights in the table are worth knowing by heart for the sizes used most: #4 at about 0.67 lb/ft, #5 at about 1.04, #6 at about 1.50 and #8 at about 2.67. A useful check: a #5 weighs about one and a half times as much per foot as a #4, and a #8 weighs about two and a half times as much as a #5.

Steel grades

ASTM A615 bars come in Grade 40, Grade 60, Grade 80 and Grade 100, named for the minimum yield strength in thousands of pounds per square inch. Grade 60 is by far the most common bar on US building projects; Grade 80 is used to reduce congestion in heavily reinforced members, and Grade 40 survives mostly in small sizes for light work. A615 bars are not made for welding. ASTM A706 bars, in Grade 60 and Grade 80, are low-alloy bars with controlled chemistry that can be welded under a proper procedure and have extra ductility; designers specify them for welded splices and for members that must bend without breaking in an earthquake. An A615 bar must not be welded, even for a tack, unless the engineer approves a procedure.

Grade matters to the placer for one simple reason: bars of the same size and different grades look almost the same, and a lower grade bar placed where a higher grade is specified can leave a member weaker than designed. Fabricators keep grades separate in their yards and on their tags, and the placer checks the grade on the tag and the bar against the drawings.

Mill markings

Every bar is rolled with a set of raised marks repeated along its length, read in order from one end: a letter or symbol for the mill that made it, the bar size number, a letter for the type of steel and a mark for the grade. The type letter is S for carbon steel bars made to A615 and W for low-alloy bars made to A706. Grade 60 bars show the number 60, or the metric 4, or one continuous line rolled between the ribs; Grade 80 shows 80, the metric 5 or two lines; Grade 100 shows 100, the metric 6 or three lines. Grade 40 bars carry no grade mark. The mill certificate, sometimes called a mill test report, lists the heat number, chemistry and test results for the steel, and the fabricator keeps it on file for every shipment.

A length of deformed bar drawn large, with its raised marks labeled in order along the bar: mill symbol, bar size, steel type or weldable designation and grade mark, with the grade lines between the ribs shaded. A smaller panel shows the same bar with a bundle tag wired to it.
Reading the marks rolled into a bar.

Markings are rolled into the bar before it is cut, so a short piece may not show all of them. On the job, the bundle tag is the first source of information, and the marks on the bar confirm it.

Coated and special bars

Most rebar is plain, uncoated carbon steel, often called black bar. Where corrosion is a concern, for example in parking structures, bridge decks and marine work, designers may specify coated or corrosion-resistant bars. Epoxy-coated bars are coated with a hard green, purple or gray film; galvanized bars are zinc-coated and look dull gray; stainless steel bars look bright and do not rust; and glass fiber reinforced polymer bars, made of fibers in resin, are light and non-metallic. Each needs its own handling: padded slings, coated chairs and coated tie wire for epoxy bars, care not to mix stainless and black steel, and the maker's rules for any bending. These bars and their handling are covered in IRW-220.

Bundle tags

Fabricated bars arrive on the job in bundles, each wired with a metal or plastic tag. A tag normally shows the job, the bar mark from the bar list, the bar size and grade, the number of pieces, the length, the shape if the bars are bent, and often the area of the building where they go. Tobias's rule is that tags stay on the bundle until the last bar is placed. A bundle with no tag is a bundle someone has to identify by measuring, counting and checking against the list, which wastes time and invites mistakes.

Bundles are sorted on site by area and by sequence so that the bars needed first are on top and nearest the work. Bars should be stored off the ground on dunnage, kept out of mud and away from oil and form release, and kept apart by size and grade. Light surface rust is normal and does no harm; loose, flaky scale or pitting should be shown to the foreperson.

Weights and bundles

The weight of a bundle matters for crane picks, for hand carrying and for checking a delivery against the bill. It is found by multiplying the number of bars by the length of each bar and by the mass or weight per unit length from the table.

Worked problem

The weight of a bundle

A bundle tag reads: 40 pieces, #5, 40 ft straight. What does the bundle weigh?

Show solution
  1. Total length = 40 × 40 = 1,600 ft.
  2. Weight = 1,600 ft × 1.043 lb/ft = 1,668.8 lb.

Answer: About 1,670 lb. Two people cannot carry a bundle like that; it comes off the truck with the crane or a forklift, and individual bars come off the bundle by hand.

Worked problem

A heavy bundle for a crane pick

A bundle of 40 pieces of #8, each 40 ft long, is to be lifted into a wall form with the crane. What does it weigh, and how should it be rigged?

Show solution
  1. Total length = 40 × 40 = 1,600 ft.
  2. Weight = 1,600 × 2.670 = 4,272 lb.
  3. Add the rigging, for example two chokers and a spreader, to the load on the hook.

Answer: About 4,272 lb before rigging. As IRW-120 explained, long bundles are picked from two points, with chokers about a quarter of the length in from each end and the bundle wire left on, never from a single choker in the middle; a bundle choked at one point can sag, and bars can slide out of the choke and fall.

Carrying single bars is a large part of a rodbuster's day, and a long day of it is hard on the back and shoulders. Bars over 20 ft long, or heavy sizes at any length, are carried by two people, on the same shoulder, walking in step, with the lead person calling the turns and the set-down. Crossbeam limits single-person carries to a weight the worker can manage comfortably and asks crews to use the crane, a forklift or a bar cart for anything more.

Bar substitutions

Sometimes the size called for is not on site, and someone suggests using a different size "that has the same steel". Substitutions change bar spacing, cover, bond and laps, and only the engineer can approve them. The placer's job is to place what is shown, and to raise any shortage with the foreperson so that the engineer can decide.

Worked problem

Why substitutions need the engineer

A wall calls for #6 bars at 12 in. Someone suggests using two #5 bars instead of each #6. Is that the same steel?

Show solution
  1. One #6 = 0.44 in² of steel.
  2. Two #5 = 2 × 0.31 = 0.62 in² of steel.
  3. The area is larger, but there are now twice as many bars, with different clear spacing, laps and bond.

Answer: No. It has more steel area, but it changes the spacing between bars, the space for concrete to flow between them and the lap lengths. Only the engineer can say whether it works, and the change must be recorded.

Telling sizes apart in the field

The size pairs that cause most mix-ups are #4 and #5, and #6 and #7, which look alike at a glance. Tobias teaches three checks. First, the tag. Second, the mill marks, which show the size number. Third, the feel: pick up a 10 ft piece of each and the difference in weight is noticeable, about 6.7 lb against 10.4 lb for #4 and #5. A bar whose size cannot be confirmed by the tag and the marks is set aside, not placed on a guess.

Remnants and offcuts are the most common source of mistakes. A short piece left over from one area, with no tag and its marks cut off, ends up as a dowel or a trim bar in the next area because it is handy. Crossbeam's rule is that untagged offcuts go back to the scrap bin unless the foreperson identifies them.

Bars by the metric ton and the truckload

Fabricators sell, ship and invoice reinforcing by weight, and general contractors schedule it by weight too. A rod gang foreperson thinks in tons: how many tons are in an area, how many tons the gang placed today, how many tons are on the next truck. Truckloads are commonly up to about 22 tons, limited by the truck and the road, but downtown sites and tight laydown areas often take smaller loads more often. Knowing the weight of what arrives lets the foreperson plan crane time, laydown space and the size of the crew.

Worked problem

Checking a delivery

A delivery ticket lists three marks: 60 pieces of #5 at 20 ft, 24 pieces of #6 at 15 ft and 80 pieces of #3 at 6 ft 6 in. What is the total weight on the truck?

Show solution
  1. #5: 60 × 20 × 1.043 = 1,251.6 lb.
  2. #6: 24 × 15 × 1.502 = 540.7 lb.
  3. #3: 80 × 6.5 × 0.376 = 195.5 lb.
  4. Total ≈ 1,988 lb.

Answer: About 1,988 lb. If the ticket total is very different, or the bundle count does not match, the foreperson checks the bundles before signing.

Storing bars by mark, with tags facing out, in the order they will be placed is a habit that pays off every day. A laydown area that looks like a scrapyard turns every search for a bar into a ten-minute job, and in a busy week those ten minutes add up to a day.

Common mistakes

  • MistakeIdentifying bars by measuring the diameter over the ribs.

    InsteadRead the tag and the mill marks; the size over the ribs is larger than the nominal diameter.

  • MistakeWelding or tacking A615 bars.

    InsteadWeld only bars made for welding, under an approved procedure, and only where the engineer allows it.

  • MistakeRemoving bundle tags as soon as a bundle is opened.

    InsteadKeep tags on until the last bar of the bundle is placed.

  • MistakeChoking a long bundle at one point in the middle.

    InsteadPick from two points about a quarter of the length in from each end.

  • MistakeSubstituting a different bar size because it has the same area.

    InsteadPlace what is shown; only the engineer can approve a substitution.

Summary and key terms

  • US bars are #3 to #18 under ASTM A615 and A706; for #3 to #8 the number is the diameter in eighths of an inch.
  • Grade 60 is the common US bar; A615 bars are not for welding, and A706 bars are weldable.
  • Mill marks show the mill, the size and the grade; the tag and mill certificate confirm them.
  • Bundle weight = number of bars × length × mass or weight per unit length.
  • Coated and corrosion-resistant bars need their own handling, covered in IRW-220.
  • Only the engineer can approve a bar substitution.
Nominal diameter
The diameter of a plain round bar of the same weight per length as the deformed bar.
Grade
The minimum yield strength class of a bar.
Mill marks
The raised letters, numbers and lines rolled into a bar to identify its mill, size and grade.
Mill certificate
The mill's record of the heat, chemistry and test results for a shipment of steel.
Black bar
Plain, uncoated carbon steel reinforcing bar.
Bundle tag
The label wired to a bundle showing its job, bar mark, size, grade, count and length.
Weldable bar
A bar with controlled chemistry made so that it can be welded under a proper procedure.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. What is the weight of 25 pieces of #6, each 20 ft long?

    Show answer

    25 × 20 × 1.502 = 751 lb.

  2. What is the nominal diameter of a #6 bar?

    Show answer

    6/8 in = 0.750 in.

  3. What does a type letter W mean on a US bar?

    Show answer

    Low-alloy steel to ASTM A706, made for welding.

  4. How many grade lines does a Grade 60 bar show?

    Show answer

    One continuous line (or the number 60 or 4).

  5. Who can approve a bar substitution?

    Show answer

    The engineer.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz