Outside plant cable types and protection

Three cable samples sit on Daniel's desk, sent by suppliers who heard about the Harbourview project. One is stiff and heavy, with a corrugated steel layer under the black jacket. One is light and round, and when Daniel cuts it open there is no gel at all, only dry tapes and yarns around the colored tubes. The third is flat and thin, with fibers bonded side by side. Roz picks up each in turn. 'All three would work,' she says. 'The question is which one survives the next forty years in this particular ground, with these particular rodents, and which one your splicer can work with on a cold March morning.'

Outside plant cables must survive conditions that indoor cables never meet: water, frost, sunlight, temperature swings, crushing loads, rodents, lightning and the forces of installation. This lesson describes how fiber and copper outside plant cables are built, how to choose among the common types and how to protect them, and how fibers and pairs are identified so that splicers at both ends connect the right ones.

Fiber cable construction

Most outside plant fiber cables use a loose tube design. Fibers, coated to about 250 micrometers or, in newer high-count cables, 200 micrometers, lie loosely inside plastic buffer tubes, usually 6, 12 or 24 fibers per tube. Because the fibers are loose and slightly longer than the tube, the cable can stretch under tension or shrink in cold without straining the glass. The tubes are wound around a central strength member, often of glass-reinforced plastic, and surrounded by water-blocking materials, strength yarns and a polyethylene outer jacket that resists sunlight and moisture.

Central tube cables put all the fibers, often in ribbons, in a single large tube with strength members embedded in the jacket. Ribbon cables group fibers side by side in flat ribbons of 12, which can be spliced twelve at a time with a mass fusion splicer, cutting splicing time on high-count cables. Newer rollable or flexible ribbons bond fibers only at intervals, so the ribbon can be rolled into a compact bundle for very high fiber counts in a small cable and flattened again for mass splicing. Microduct cables, very small and light, are blown into small ducts with compressed air and suit dense campus and city networks.

Keeping water out

Water in a fiber cable is a long-term threat. It can freeze and crush fibers, and over many years it can weaken the glass. Older cables filled every space with a petroleum gel. Gel works well but is messy to clean before splicing and takes time on a cold day. Most new cables are dry: they use water-swellable tapes and yarns that absorb any water that enters and swell to block it from traveling along the cable. Dry cables are lighter, cleaner and faster to prepare for splicing, and most splicers prefer them. Some designs still gel-fill the buffer tubes while keeping the core dry.

Jackets and armor

The outer jacket of outside plant cable is usually medium-density or high-density polyethylene, which resists moisture, sunlight and abrasion. It burns readily, which is why these cables must transition to listed indoor cable at the building entrance, as Lesson 10 explained. A cable may have one jacket or two, with armor between them.

Armor is a layer of corrugated steel tape, sometimes coated with plastic, wrapped around the core. It resists crushing and protects against rodents, which are a serious threat to buried and aerial cable in many regions: gophers, squirrels and rats chew jackets, and a single bite can break fibers. Armor also has costs. It makes the cable heavier and stiffer, it is conductive, so it must be bonded at building entrances and in structures, and it adds a path for lightning current into the cable route. Dielectric alternatives use glass yarns or hard jackets that discourage rodents without adding metal.

Fiber types for outside plant

Nearly all outside plant fiber today is singlemode. The most common type follows the ITU-T G.652.D recommendation, a low water peak singlemode fiber that works across the 1310 nm to 1625 nm range. Bend-insensitive singlemode fibers, defined in ITU-T G.657, tolerate tighter bends with less added loss and are common in drop cables, in closures and in high-count cables where fibers are packed tightly; the G.657.A categories are designed to splice and work with G.652.D fiber. The designer should specify the fiber type by recommendation and category so that all cables in a system are compatible.

Identifying fibers and tubes

A splicer at one end of a 144-fiber cable must connect fiber 87 to fiber 87 at the other end. Fibers and tubes are identified by a standard sequence of twelve colors, set in North America by ANSI/TIA-598. The same twelve colors mark the fibers within each tube and the tubes within the cable.

With 12 fibers per tube, fiber numbers map directly to tube and fiber colors. Fibers 1 to 12 are in the blue tube, 13 to 24 in the orange tube and so on.

Copper outside plant cable

Outside plant copper cable carries twisted pairs in counts from a few pairs to thousands, in gauges commonly 24, 22 or 19 AWG. The core is filled with a gel compound to keep water out, or, in older networks, kept dry with air pressure. A metallic shield, usually corrugated aluminum or steel, surrounds the core and must be bonded at every splice and at each building entrance to provide a continuous path for induced currents, as RCDD-113 discussed. Pairs are identified with the standard telephone color code: groups of 25 pairs formed by five main colors (white, red, black, yellow, violet) combined with five minor colors (blue, orange, green, brown, slate), with larger cables built from color-coded binder groups of 25 pairs.

Protecting cables in the route

Cable choice is one layer of protection. The route provides the others. Underground, ducts and concrete encasement protect against crushing and digging, marker tape and tracer wire help others find the cable before they dig, and depth protects against frost and surface work. Aerial cables are protected by guards where they run down poles, by slack loops that allow repairs, and by placement away from tree limbs where possible. In structures, cables are racked off the floor, sealed in ducts and tagged.

Rodents deserve specific planning. In northern Minnesota and northwestern Ontario, pocket gophers and other burrowing animals are less of a problem than in the prairies to the west, but squirrels on aerial routes and mice and rats in ducts are common everywhere. Rodent-resistant designs include steel armor, glass yarn armor and hard nylon or polyamide outer jackets. Sealing ducts keeps animals out of the route altogether.

Lightning and induced voltage

Long metallic paths in cable routes, such as armor, copper shields and strand, can pick up voltage from lightning strikes and from faults on nearby power lines. Bonding those paths at intervals and at both ends limits the voltage. All-dielectric fiber cable avoids the problem entirely, which is why many campus designs use dielectric cable in ducts even where armor would add rodent protection. If armor is needed, the designer specifies bonding at each structure and entrance.

Cable handling and storage

Outside plant cable is shipped on reels, and reel length limits how far a single cable can run without a splice. Common reel lengths for fiber are several kilometers, far more than a campus link needs, but large-diameter copper cables may come in shorter lengths, which forces splice points. Reels must be stored and handled so that the cable is not crushed or kinked, and cold-weather installation needs care: polyethylene jackets stiffen in the cold, and many cables have a minimum installation temperature below which they should not be pulled or bent.

Cable specifications that matter

A data sheet for outside plant cable lists many values, and a few of them decide whether a cable suits a route. Maximum rated tensile load during installation sets the pulling limit used in Lesson 7. Long-term rated load, much lower, is the force the cable can carry permanently, which matters for aerial spans and vertical runs. Minimum bend radius is usually given twice: a larger value under tension during installation and a smaller one when installed. Crush resistance tells how much load the cable can take without damage, which matters for direct burial. Operating and installation temperature ranges matter in northern climates, where the installation range may stop work for part of the winter. And the cable's outside diameter decides how many cables fit in an innerduct or duct.

The designer should copy these values into the specification or require cables that meet stated minimums, so that a substitute cable offered by the contractor can be checked against them. Two cables with the same fiber count can differ widely in diameter, weight and tensile rating, and a substitute that is heavier or weaker may not survive the pulls that were planned for the original.

Exam focus: identification

Questions about color codes are a favorite because the answer can be worked out exactly. Remember the order, blue, orange, green, brown, slate, white, red, black, yellow, violet, rose, aqua, and practice mapping fiber numbers to tubes and positions until it becomes automatic.