PWR-340 · Lesson 11 of 12 · 21 min
Owner responsibilities and jurisdictional inspection
▶ Video coming soon A video version of this lesson is on the way.
Cantwell's certificates of operation hang in a glass frame by the control room door: one for each boiler, each showing its state number, its allowed pressure and the date it expires, by which the next inspection must be done. Grazyna stopped beside the frame on her way out of the session on incident investigation. "Who is responsible for every one of these?" she asked. Okonkwo guessed the state, then the insurance company, then her. "The owner," she said. "Not the inspector, not the state. The law puts the duty on the owner, and the owner puts it on the chief engineer, which today is me and one day will be you."
This lesson sets out what owners of boilers and pressure vessels must do under Ohio's law, the jurisdiction Cantwell operates in, and how inspection is organized in Ohio and other US states: the state's general inspectors, the insurance companies' special inspectors, the National Board's commissions and the owner-user inspection organizations some large plants run. It covers inspections and certificates of operation, extended inspection intervals, notifications, repairs and records, and closes with the chief engineer's practical checklist.
The owner's duty
In Ohio, Chapter 4104 of the Revised Code and the boiler rules make the owner or user of a boiler responsible for keeping it, and its equipment, in safe working order. The owner must ensure that it is built to the ASME code and registered with the state, inspected at the required intervals, and covered by a current certificate of operation; that it is not operated above the pressure on that certificate; that it is run by licensed operators where the law requires them; and that repairs follow the state's rules and the NBIC. The duty cannot be handed to a contractor or an inspector. An inspector checks the owner's equipment at intervals; the owner is responsible every day in between.
In practice the owner gives this duty to a named person. At Cantwell that is the chief engineer, whose job description says, in effect, that she must know what pressure equipment the plant has, what condition it is in, and what the law requires of it, and must make sure it is done.
Inspections and certificates in Ohio
Ohio's boiler inspection rules, in their current form since January 1, 2026, require power boilers to be inspected internally and externally under operating conditions at least once a year, and process boilers at least once every three years. Inspections are carried out by the state's general inspectors or by special inspectors employed by insurance companies, such as Ottoline Brackwater, who hold National Board commissions and Ohio commissions. The inspector reports to the superintendent, and the certificate of operation is issued or renewed when the boiler passes. No certificate is issued or renewed until the boiler passes an inspection, and the owner must prepare the boiler for inspection as the rule describes: shut down, cooled, cleaned, opened and isolated.
An owner may apply to the superintendent for a longer interval: biennial for power boilers, or longer for process boilers. The application must include the boiler's data, the name, registration and qualifications of the professional engineer in charge of water treatment, the laboratory facilities for testing boiler water, the sampling method and frequency, the percentage of makeup water, the record of outages since the last internal inspection, and an inspector's report on the boiler's suitability. If approved, later certificates follow the longer schedule unless the superintendent withdraws approval.
Worked problem
Counting Cantwell's inspections
Cantwell has three power boilers (high-pressure steam boilers) and two hot water boilers. Using the one-year interval for power boilers, how many power boiler inspections fall due each year, and how many would there be in a year if the state approved biennial inspection for all three and their inspections were staggered?
Show solution
- Annual:
- \[3 \times 1 = 3 \text{ per year}\]
- Biennial, staggered:
- \[3 \times \tfrac{1}{2} = 1.5 \text{ per year on average}\]
Answer: Three a year, or an average of one and a half with biennial approval. The saving in outages is real, but the conditions for approval, a professional engineer in charge of water treatment, a laboratory and good records, are a commitment of their own. Grazyna has not applied; with three boilers and summer standby periods, annual inspection fits the plant's rhythm, and she prefers to see inside the drums every year.
Repairs, alterations and the NBIC
Ohio's rules on existing boilers divide work into routine repairs, major repairs and alterations. Routine repairs without welding, such as replacing tubes by rolling, need no permit. Routine repairs involving welding need a permit and an inspector's approval before work begins; if the contractor or owner holds a National Board R certificate, its authorized inspector approves the repair. Major repairs and alterations, including re-rating, to ASME-stamped or Ohio-numbered boilers must follow NBIC Part 3, and alterations require an R certificate holder and an authorized inspector. Welding follows Section IX. Replacing or repairing safety valves, controls and other fittings must meet the requirements for a new installation.
The R certificate is what makes a repair trustworthy after the welder has left. To hold one, an organization must have a written quality system accepted by the National Board and an agreement with an authorized inspection agency, and the National Board reviews it periodically. Its repairs are documented on National Board repair or alteration forms, filed with the state and the National Board and marked on a repair nameplate. When Grazyna reviews a contractor, she asks for its certificate and the date of its last review before she asks for a price.
Owner-user inspection organizations
Large plants in many states can run their own owner-user inspection organization (OUIO), accredited under the National Board's NB-371 program and accepted by the jurisdiction. The owner employs its own inspectors, who hold National Board owner-user commissions and work independently of production, under a written quality program that the National Board and the jurisdiction review. An OUIO inspects the owner's own equipment, typically pressure vessels in refineries and chemical plants, and may accept repairs within its scope. Whether an OUIO may inspect boilers in a particular state, and for what, depends on that state's rules.
Cantwell is too small for an OUIO, and its insurance company's inspection is part of its insurance. But the elements of the program, independent inspectors, written methods, calibrated instruments, controlled records and audits, are the same ones any owner needs to manage equipment well.
Commissions and the National Board
The National Board of Boiler and Pressure Vessel Inspectors, whose members are the chief inspectors of the states and provinces, supports this system in several ways that a stationary engineer meets. It commissions inspectors: a general or special inspector must pass the National Board's examination and meet its experience requirements, and an Ohio inspector also holds the state's commission. It accredits organizations: R and VR certificate holders, authorized inspection agencies and owner-user inspection organizations. It registers boilers and vessels, keeping the manufacturer's data reports, so that an owner can obtain a copy of a boiler's original data report decades after it was built.
The National Board also publishes guidance and investigates incidents, and its annual reports of boiler and pressure vessel incidents in the US and Canada are a useful reminder of how often the same causes recur: low-water conditions, operator error and poor maintenance, and failures of controls and safety devices. For a stationary engineer, a National Board commission is also a career path: many plant engineers become insurance company or state inspectors later in their working lives.
For Okonkwo, the point was that every part of the US system depends on qualified, independent people working under written programs that someone audits: the manufacturer and its authorized inspector, the repair organization and its quality system, the special inspector and his or her commission, and the owner and its records. "The state cannot watch every boiler every day," Grazyna said. "It watches the people and the programs. The owner who runs a good one has the least trouble."
Records
Good records are the owner's evidence of compliance and the integrity program's memory. A pressure equipment file for each item holds:
- The manufacturer's data report, drawings and design calculations, with the design registration or CRN where applicable, and the National Board registration.
- The certificates of operation and every inspection report, with findings and how each was resolved.
- Repair and alteration records: the approvals, procedures, welder qualifications, material test reports, examination reports, pressure test records and repair data reports or forms.
- Relief device records: nameplate data, capacity certification, set pressure, and every test, repair and replacement.
- Thickness and condition data from the integrity program, with the corrosion rate and remaining life calculations (lesson 7).
- Operating history that matters to integrity: water chemistry, layup periods, upsets such as low-water events and overpressure, and changes approved through MOC.
Repair records are kept for the life of the equipment. They often answer the hardest questions years later: what material was used in that patch, who welded it, and what the inspector accepted.
The chief engineer's checklist
Grazyna's own list, taped inside the cover of her binder, condenses the owner's duties into a page:
- Every registered item is in the equipment register, with its file complete.
- Every certificate is current, and the next inspection dates are booked and staffed.
- Every relief device is within its servicing interval, sealed, with its record up to date.
- Every repair or alteration has the jurisdiction's approval before it starts, and the paperwork after.
- Every change to pressure equipment, its relief devices or its safety systems has been through MOC.
- Every required notification has been made on time.
- Operators are certificated or licensed as the plant requires, and trained on current procedures.
- Integrity findings and recommendations are tracked to closure.
"If I can tick every line on a Monday morning, I sleep well," she said. "If I cannot, I know exactly what to do that week."
Preparing for the inspector
An inspection goes well when the owner has done the preparation, and Ohio's rule on inspections spells out what the owner must do once the inspector gives notice. For an internal inspection of a boiler, that means shutting it down and cooling it slowly, cleaning the fire side and setting, draining it, removing the manhole and handhole plates and other openings, washing out the water side, and closing and securing the feedwater and blowoff valves before anyone enters, together with any other preparation the inspector requires. If the preparation is not done, the inspector may decline to inspect, and no certificate is issued or renewed until the boiler passes.
Paperwork is part of the preparation. Grazyna sends the inspector, a week ahead, the item's file summary: the last inspection report and how each finding was resolved, any repairs since, the relief device records, the thickness readings and corrosion rates, and the operating history that matters, such as low-water events, layup periods and water chemistry problems. On the day, she or the shift engineer goes round with the inspector, answers questions and writes down every comment. The inspector's report arrives later, but the plant's own notes mean that work on the findings can start the same week.
Some things the inspector will always ask about: whether the low-water cutouts and the safety valves have been tested as the procedure requires; whether the gauge glass and water column are clear; whether the logbook shows the blowdowns and tests; whether any repairs were made without approval; and whether anything about the boiler or its operation has changed. A plant that can answer those quickly, from records, earns the inspector's confidence, and that confidence matters when a difficult decision has to be made together, as with boiler 3's tube repair in November.
Insurance and inspection
In Ohio, as in most states, most boilers in commercial and industrial plants are insured against breakdown and explosion, and the insurance companies' special inspectors do most periodic inspections, reporting to the state. The insurer has its own interest in the equipment's condition: an insurer that finds a dangerous condition may require repairs or cancel cover, and a boiler that is not insured is inspected by the state's general inspectors. The insurer's engineering staff also offer advice on maintenance, water treatment and operation, and its loss reports are a useful record of what goes wrong across many plants.
Ottoline Brackwater has inspected Cantwell's boilers for several years. Grazyna treats her as a colleague whose independence is the whole point. "She is not here to help me run the plant," she told Okonkwo. "She is here to tell me, and the regulator, whether it is safe. The day an inspector becomes too friendly to say no is the day the system stops working."
Common mistakes
MistakeThinking the inspector is responsible for the equipment's safety.
InsteadThe owner is responsible every day; the inspector checks at intervals.
MistakeRunning a boiler past the expiry of its certificate of operation.
InsteadBook inspections early; an expired certificate means the item may not operate.
MistakeStarting a welded repair before an inspector has approved it.
InsteadGet the required approval first, then do the work.
MistakeHiring a repair contractor on price without checking its certification.
InsteadConfirm its quality program or R certificate and recent audit first.
MistakeKeeping repair records only until the next inspection.
InsteadKeep them for the life of the equipment.
MistakeAssuming one state's rules apply in another.
InsteadEach jurisdiction's rules govern within it; check the local requirements.
Summary and key terms
- In Ohio the owner or user is responsible for boilers under Chapter 4104 of the Revised Code and the boiler rules; the duty rests in practice on the chief engineer.
- Power boilers are inspected internally and externally at least once a year, process boilers every three years, unless longer intervals are approved on a detailed application.
- General and special inspectors hold National Board and Ohio commissions; the certificate of operation is issued only after an inspection is passed.
- Welded repairs need an inspector's approval first; major repairs and alterations follow NBIC Part 3, and alterations need an R certificate holder.
- Owner-user inspection organizations and National Board accreditation let qualified owners inspect their own equipment under audited programs.
- Complete records, kept for the life of the equipment, are the owner's evidence and memory.
- Owner or user
- The person or organization legally responsible for a boiler's safety.
- Certificate of operation
- Ohio's certificate allowing a boiler to operate at a stated pressure until it expires.
- General inspector
- An inspector employed by the state.
- Special inspector
- An inspector employed by an insurance company and commissioned to inspect insured boilers.
- R certificate
- The National Board's certificate of authorization for repairs and alterations.
- Authorized inspection agency
- An organization whose inspectors oversee code construction or repair work.
- Owner-user inspection organization
- An owner's own inspection department accredited to inspect its equipment.
- Repair data report
- The record of a repair or alteration, kept for the life of the equipment.
Practice problems
Work each problem on paper first, then reveal the answer to check.
How often must an Ohio power boiler be inspected internally and externally?
Show answer
At least once a year, unless biennial inspection is approved.
Who must approve a welded routine repair before work begins?
Show answer
A general or special inspector, or the authorized inspector of an R certificate holder.
What code governs major repairs and alterations to ASME-stamped boilers in Ohio?
Show answer
NBIC Part 3.
Name two items an application for biennial inspection must include.
Show answer
For example, the engineer in charge of water treatment and the record of outages since the last internal inspection.
Lesson quiz · 5 questions
Score 60% or more to complete this lesson.
Create a free account to save your progress, take quizzes and earn a certificate.