A2L refrigerants: safe charging and service

The Lindqvist family's new ducted heat pump was the first R-454B installation Theo had worked on from start to finish. The outdoor unit had a red band around the refrigerant label and a notice about mildly flammable refrigerant; the indoor unit, in a small basement furnace room, came with a refrigerant detection sensor already wired to its board. Before they left the shop, Dana walked Theo through the van: an A2L-rated recovery machine, a vacuum pump listed for A2L use, a leak detector rated for the refrigerant, left-hand-thread cylinder adapters and a fire extinguisher. "Nothing about the vapour-compression cycle changes," she said. "What changes is that this refrigerant can burn if enough of it leaks into a small room and meets a spark. So everything we do today is about not letting that happen."

New air conditioners and heat pumps in Canada and the United States have been moving from R-410A to lower-GWP refrigerants, mainly R-454B and R-32, which are classed as A2L: lower toxicity and lower flammability. RAC-110 introduced the safety classes and RAC-120 the regulations that drive the transition. This lesson covers what A2L means in practice, the codes and standards that govern A2L equipment, how to handle, charge, evacuate and recover A2L systems safely, and how charge limits and refrigerant detection systems protect occupied spaces.

What A2L means

Safety classes, under ASHRAE Standard 34 and its equivalent ISO 817, use a letter for toxicity, A for lower and B for higher, and a number for flammability, 1 for no flame propagation, 2 for lower flammability, 3 for higher flammability. The subclass 2L covers refrigerants that are flammable but burn slowly, with a burning velocity of no more than about 10 cm/s (4 in/s), and that need a fairly high concentration in air to ignite. Their lower flammability limit (LFL), the lowest concentration in air that can burn, is much higher than for a hydrocarbon like propane, and they are harder to ignite, typically needing an open flame or a strong spark rather than a small static discharge.

A2L does not mean safe to ignore. Burning A2L refrigerant produces hydrogen fluoride and other toxic decomposition products, the same hazard that any fluorinated refrigerant creates in a fire or at a torch flame. And although an A2L is hard to ignite, a large release into a small, closed space can reach its LFL. The codes for A2L equipment are written to keep concentrations well below that level.

Codes and standards

In Canada, A2L equipment is governed by CSA B52:23, the Mechanical Refrigeration Code, as adopted by each province, together with the electrical safety standard for the equipment, CSA C22.2 No. 60335-2-40. In Ontario, the Technical Standards and Safety Authority adopted CSA B52:23 in October 2024. B52 sets requirements for charge limits by room size, ventilation, refrigerant detection and the location of equipment, and building, gas and electrical codes apply alongside it. Federal halocarbon rules, covered in RAC-120, limit the GWP of refrigerants in new equipment, which is why manufacturers are moving to A2Ls. Technicians handling refrigerants also need their ozone depletion prevention card, and provincial rules may add A2L-specific training, so check the current requirements of your province.

Equipment manufacturers' installation instructions are written to these standards and often go further: they state the maximum charge for the unit, the minimum room area for the indoor unit, whether a refrigerant detection system is fitted and how to test it, which joints are allowed in occupied spaces, and how the unit must be labelled. Those instructions are part of the code compliance for the installation.

Charge limits and room size

The basic idea behind A2L charge limits is that if the entire charge leaked into the room served by the indoor unit, the concentration should stay well below the LFL. A larger room, or a unit mounted high on a wall where leaked refrigerant mixes before reaching the floor, allows a larger charge. Earlier editions of the equipment standard expressed the maximum charge for a room with a well-known formula, which still shows the logic clearly even though current editions use more detailed methods and allow larger charges when refrigerant detection and mitigation are provided.

Here m_max is in kilograms, LFL in kilograms per cubic metre, h_0 is a height factor for the indoor unit's mounting (about 0.6 for floor-mounted, 1.0 for window, 1.8 for wall-mounted and 2.2 for ceiling-mounted units in that formula), and A is the room's floor area in square metres. Rearranged, the same formula gives the minimum floor area for a given charge.

# Illustrative A2L room charge limit using the older IEC 60335-2-40 formula
# (current editions use more detailed methods; always follow the manufacturer's instructions)
LFL = {"R-454B": 0.296, "R-32": 0.307}      # kg/m3, approximate
h0 = {"floor": 0.6, "wall": 1.8, "ceiling": 2.2}

def m_max(ref, area_m2, mount):
    return 2.5 * LFL[ref] ** 1.25 * h0[mount] * area_m2 ** 0.5

def min_area(ref, charge_kg, mount):
    return (charge_kg / (2.5 * LFL[ref] ** 1.25 * h0[mount])) ** 2

for area in [8, 15, 30, 60]:
    print(f"room {area:3d} m2: R-454B wall unit up to {m_max('R-454B', area, 'wall'):4.2f} kg, floor unit up to {m_max('R-454B', area, 'floor'):4.2f} kg")
charge = 3.4
print(f"\na {charge} kg R-454B charge would need about {min_area('R-454B', charge, 'floor'):.0f} m2 for a floor-level unit")
print(f"and about {min_area('R-454B', charge, 'ceiling'):.0f} m2 for a ceiling unit by this formula;")
print("ducted systems in small rooms rely instead on refrigerant detection, ventilation and the manufacturer's limits")

room   8 m2: R-454B wall unit up to 2.78 kg, floor unit up to 0.93 kg
room  15 m2: R-454B wall unit up to 3.81 kg, floor unit up to 1.27 kg
room  30 m2: R-454B wall unit up to 5.38 kg, floor unit up to 1.79 kg
room  60 m2: R-454B wall unit up to 7.61 kg, floor unit up to 2.54 kg

a 3.4 kg R-454B charge would need about 108 m2 for a floor-level unit
and about 8 m2 for a ceiling unit by this formula;
ducted systems in small rooms rely instead on refrigerant detection, ventilation and the manufacturer's limits

The numbers show why ducted A2L systems need extra protection. A typical residential charge is too large for a small furnace room by the simple formula, so ducted A2L equipment above a small charge threshold, about 1.8 kg (4 lb) in many cases, is supplied with a refrigerant detection system (RDS). The sensor sits in the indoor unit; if it detects refrigerant, the board turns on the indoor blower to mix and dilute the leak through the ductwork, shuts down the compressor and may disable ignition sources such as an electric heater. Ductless wall units, mounted high, can often carry their charge in smaller rooms.

Tools and handling

• Use recovery machines, vacuum pumps and leak detectors that the manufacturer lists as suitable for A2L refrigerants. Their motors, switches and relays are designed so they will not ignite a mildly flammable mixture.
• A2L cylinders have left-hand threads and a red band or marking, so A2L refrigerant cannot be connected to R-410A equipment by accident. Use the correct adapters and hoses, and store and transport cylinders upright, secured and away from heat, with the transport rules in RAC-120.
• Use recovery cylinders rated and labelled for the refrigerant, and do not mix A2L refrigerant with other refrigerants in a recovery cylinder.
• Remove ignition sources from the work area: no smoking, no open flames until the system has been recovered and purged, and caution with tools that spark. Ventilate enclosed work areas, and use a refrigerant detector to check the area before and during work.
• Never braze on a system that may still contain refrigerant. Recover, evacuate and purge with dry nitrogen first, then braze with nitrogen flowing, as RAC-210 described for all refrigerants.
• Keep a suitable fire extinguisher nearby, as for any hot work.

Charging and service steps for A2L systems

The methods from lessons 8 to 10 apply, with these additions from typical manufacturers' instructions:

• Pressure-test with dry nitrogen and leak-check every field joint before evacuating. Some manufacturers allow only brazed joints or listed mechanical connectors in occupied spaces; flare joints, where allowed, must be made with the specified flare type and torque.
• Evacuate to the manufacturer's target and run a decay test, as in lesson 8.
• Charge by weight, with the nameplate charge plus the line set adjustment, and never above the maximum charge stated for the room on the unit's label or instructions. R-454B and R-32 are charged as liquid or vapour as the manufacturer allows; R-454B is a blend with small glide and is normally charged as liquid.
• Mark the total charge on the unit's label, as the instructions require, and keep the A2L labelling and notices on the equipment.
• Test the refrigerant detection system as the manufacturer describes, typically with a test function on the board, and confirm that the blower starts and the compressor stops.
• When recovering, use A2L-rated equipment, ground the recovery machine and cylinder as instructed, and purge the system with nitrogen after recovery before opening it.

Commissioning the Lindqvist heat pump

Theo and Dana pressure-tested the brazed line set joints at the manufacturer's test pressure with dry nitrogen, held it for the specified time, and checked every joint with a bubble solution and the A2L detector. The furnace room was 7 m² (75 ft²), with a ducted indoor unit, so the charge was protected by the RDS rather than by room area. The outdoor unit's nameplate charge of 3.06 kg (6.75 lb) covered a line set of 7.6 m (25 ft); the actual line set was 10.7 m (35 ft), so the instructions called for about 0.17 kg (0.4 lb) more, bringing the total to 3.23 kg (7.15 lb), under the unit's stated maximum. After evacuation to 40 Pa (300 microns) and a decay test that settled at 60 Pa (450 microns), Theo weighed in the charge as liquid. He ran the board's RDS test, watched the blower start and the outdoor unit stop, cleared the test, and then checked the system in its cooling test mode against the manufacturer's chart. He wrote the total charge on the label with a permanent marker and left the homeowner the manual's section on what the unit does if it detects a leak.

Leak detection on A2L systems

Electronic leak detectors respond differently to different refrigerants, and some older heated-diode and infrared detectors were not designed or listed for use with flammable refrigerants. For A2L systems, use a detector that its manufacturer rates for the refrigerant, check it against a reference leak before use, and move it slowly around each joint, below it where possible, because R-454B and R-32 vapour is heavier than air. Confirm a suspected leak with bubble solution. Ultrasonic detectors and nitrogen with trace gas are other options for difficult systems. Never use an open-flame halide torch, an old method still mentioned in some books, on any modern system.