Construction equipment types and selection

Heavy equipment turns earthwork quantities into finished grades. On a typical site project, equipment is one of the largest costs and the factor that most often sets the pace of the work. Choosing the wrong machine, or the wrong combination of machines, can double the cost of moving a cubic metre of soil. This lesson surveys the main types of construction equipment, what each does well, and the physical factors that limit what a machine can do on a given site: rolling resistance, grade resistance, traction and ground conditions. The next lesson turns to productivity and cost.

Excavators

The hydraulic excavator is the most versatile machine on most sites. It digs below its tracks, loads trucks, digs trenches, handles pipe, breaks rock with a hammer and grades slopes. Sizes range from mini excavators of 1 to 6 tonnes for utility work and tight sites, through mid-size machines of 20 to 35 tonnes that do most site work, to mass excavation machines of 50 tonnes and more. Bucket capacity rises with size, from a fraction of a cubic metre to several cubic metres.

• Strengths: digs below grade, loads trucks efficiently, works on rough ground, accurate trenching, many attachments (hammers, thumbs, compaction wheels, tilt-rotators).
• Limitations: slow to move between work areas, needs trucks to haul, swing radius creates a struck-by hazard zone, limited reach.

Backhoe loaders combine a small excavator arm with a front loader on a wheeled tractor. They are mobile on roads and useful on small sites, but less productive than dedicated machines. Long-reach and high-reach excavators handle deep excavation and demolition.

Dozers

Crawler dozers push material with a blade, rip hard ground with a rear ripper, spread fill and do rough grading. They have excellent traction on tracks and can work on poor ground and steep slopes. Blade types include the straight blade for grading and spreading, the universal (U) blade with wings for pushing large volumes over longer distances, and the semi-U blade as a compromise. Many dozers now have GNSS machine control for finish grading.

Dozers are efficient only over short distances. A dozer pushing material loses productivity rapidly beyond about 50 to 100 metres, because it must reverse empty and part of the load spills from the blade ends. Dozers are also used to push-load scrapers and to clear land.

Loaders

Wheel loaders scoop material with a front bucket and load it into trucks or move it short distances. They are fast and mobile, and they excel at loading from stockpiles, handling aggregates and working in plants. They cannot dig below their wheels and struggle with hard or undisturbed ground. Track loaders dig better and have better flotation, but they are slower. Compact track loaders and skid steer loaders are small, highly versatile machines used for site cleanup, landscaping, grading and material handling, with dozens of attachments.

Scrapers

Wheel tractor-scrapers load, haul and spread material in one machine. A scraper lowers its bowl and cuts a thin layer of soil as it moves forward, hauls the load at speed, and spreads it in a controlled layer at the fill. Single-engine scrapers usually need a push dozer to load; tandem-powered and push-pull scrapers can load themselves in good conditions; elevating scrapers use a conveyor-like elevator to load without assistance.

Scrapers are the most economical machines for moving large volumes of common earth over haul distances of a few hundred metres to well over a kilometre, on sites with room to manoeuvre. They are less suited to rock, very wet ground, small sites and areas near structures.

Haul units

Trucks move material over longer distances. Articulated dump trucks, with a pivot between the cab and the dump body and all-wheel drive, handle rough haul roads and soft ground on construction sites, typically carrying 25 to 45 tonnes. Rigid-frame off-highway trucks carry much larger loads on well-built haul roads in mines and quarries. Highway dump trucks and tractor-trailers move material on public roads and are limited by legal axle loads.

Highway trucks are subject to provincial weight and dimension limits, and loads must be covered or secured. Most Canadian provinces limit the allowable gross vehicle weight by axle group, and seasonal load restrictions in spring reduce allowable weights on many roads during the thaw.

A truck's capacity is stated both by weight (payload) and by volume (struck and heaped body capacity). Which one limits a load depends on the density of the material: a load of light, fluffy topsoil fills the body before reaching the weight limit, while wet clay or rock reaches the weight limit before the body is full.

Graders and compactors

Motor graders shape and trim surfaces to close tolerances using a long blade mounted between the front and rear axles. They cut ditches, shape road crowns and cross slopes, spread and trim granular base, and maintain haul roads. GNSS or laser machine control on graders achieves finish grade tolerances of about 10 to 15 millimetres.

Compactors increase the density of soil and granular materials so that fills and subgrades support loads without settling. The right compactor depends on the material.

Compaction is specified as a percentage of a laboratory maximum density, typically 95 per cent of Standard Proctor for general fill and 98 or 100 per cent under structures and pavements, at a moisture content near optimum. It is checked with nuclear density gauges or other field tests. Lift thickness matters: most rollers can compact only 150 to 300 millimetres per lift, so placing thick lifts gives a dense surface over loose soil.

Lifting and material handling

Cranes and lifting equipment are covered in more detail in other courses, but they are part of equipment planning on every building project.

• Mobile cranes, including truck-mounted and rough-terrain hydraulic cranes and crawler cranes, lift steel, precast, equipment and formwork. Their capacity depends on boom length, radius and configuration and must be read from the load chart.
• Tower cranes serve high-rise and congested sites for the duration of the structure.
• Telehandlers (telescopic handlers) lift and place materials on scaffolds, roofs and upper floors.
• Forklifts and material hoists move materials around the site and up the building.
• Concrete pumps, boom and line types, place concrete where trucks and buckets cannot reach.

Crane operation is regulated provincially, with certified operators and requirements for inspection, load charts and lift planning. CSA Z150 covers mobile cranes and CSA Z248 tower cranes.

Resistance to motion: rolling and grade resistance

Whether a machine can move a load at a useful speed depends on the forces resisting it. Two resistances act on every wheeled or tracked machine.

• Rolling resistance is the force needed to overcome tire flexing and the sinking of wheels into the haul road surface. It is expressed in kilograms per tonne of gross weight, or as an equivalent percentage grade. A well-maintained hard haul road might have a rolling resistance of about 2 per cent; a rutted, soft road 8 to 10 per cent or more. For tracked machines, rolling resistance is largely built into the machine's rated performance.
• Grade resistance is the component of the machine's weight acting down a slope. It equals about 1 per cent of gross weight for each 1 per cent of grade uphill. Going downhill, grade becomes grade assistance.

Adding them gives the total resistance, often expressed as an effective grade: rolling resistance in per cent plus grade in per cent. A loaded truck climbing a 5 per cent ramp on a road with 4 per cent rolling resistance faces the same resistance as climbing a 9 per cent ramp on a perfect road.

Manufacturers publish rimpull and speed charts showing, for each gear, the maximum pull a machine can deliver at its drive wheels and the corresponding speed. Entering the chart with the gross weight and effective grade gives the maximum speed the truck can sustain on that section of road, which is the key input for cycle time calculations in the next lesson. Downhill, retarder charts give the safe speed under braking.

Traction and ground conditions

A machine can only use as much pull as its drive wheels or tracks can transmit to the ground without slipping. The usable pull is the weight on the driving wheels or tracks multiplied by the coefficient of traction, which depends on the surface. Tracks grip far better than tires on soft or loose ground.

Ground bearing capacity matters too. Soft ground limits the size of machine that can work without bogging down, and outrigger and track pressures for cranes must be checked against the ground's capacity. Wet weather can turn a productive site into one where only tracked machines can move, so the equipment plan should consider the season and drainage.

Altitude and temperature also affect performance. Naturally aspirated diesel engines lose power at high altitude because of thinner air; turbocharged engines are less affected but still derate above a certain elevation. Cold weather affects starting, hydraulics and tire performance.

Selecting equipment

Equipment selection balances the job requirements against the capabilities and costs of available machines.

• The material: soil type, rock, moisture, and whether it must be ripped, blasted or broken.
• The haul distance and route: short pushes for dozers, middle distances for scrapers, long hauls for trucks.
• The volume and schedule: large volumes justify larger machines and larger fleets.
• The site: space to manoeuvre, overhead lines, nearby structures, public roads, noise and vibration limits.
• Ground conditions and weather: traction, bearing capacity and the season.
• Precision: finish grading needs graders or dozers with machine control.
• Availability, cost and the contractor's own fleet: what is owned, what can be rented and what operators are available.

Safety around heavy equipment

Struck-by and caught-between incidents involving heavy equipment are among the leading causes of serious injury and death in construction. Machines have large blind spots, and operators may not see a worker standing close behind or beside them. Excavator swing radii, reversing trucks and rollers on slopes are particular hazards.

• Plan traffic routes that separate pedestrians from equipment, and use spotters where separation is not possible.
• Require high-visibility clothing, backup alarms or proximity detection, and cameras on large machines.
• Barricade excavator swing radii and crane counterweight swing areas.
• Use seat belts with rollover protective structures (ROPS); never jump from a tipping machine.
• Locate underground utilities before digging through the provincial one-call service, such as Ontario One Call or BC 1 Call, and hand-expose within the tolerance zone.
• Keep machines and loads clear of overhead power lines by the minimum approach distances in the regulations.