APP-220 · Lesson 3 of 12 · 22 min

Front-load washers, bearings and suspensions

▶ Video coming soon A video version of this lesson is on the way.

Once the top-loader was back on its feet, Harriet turned to the 2017 front-load washer. She took off the top panel, then the front panel after releasing the door boot's outer clamp, and stood back so Kiran could see the inside: the outer tub, almost filling the cabinet, hung from two springs at the top and sat on two shock absorbers at the bottom, with a concrete counterweight bolted across its front. "Everything in here is about weight and vibration," she said. "This drum spins at 1,200 rpm with a wet load in it. The tub, the springs, the shocks and that block of concrete are what keep the washer from walking out of the laundry room."

This lesson covers the front-load washer's tub and drum, the drum's bearings and seal, the spider that carries the drum, the suspension and counterweights, the door boot and door lock, and the odor and mold complaints that front-load washers are known for. It uses one of Dee's case files to show how a bearing failure is diagnosed and how the repair-or-replace decision is made.

Tub, drum and spider

A front-load washer turns on a horizontal or slightly tilted axis. The outer tub, usually made of a plastic composite, is a closed container with an opening at the front sealed to the cabinet by the door boot. Inside it, the stainless steel drum holds the clothes; its baffles, or lifters, raise the load as the drum turns. The drum is carried at the back by a spider: a three-armed casting, usually aluminum, bolted to the back of the drum, with a steel shaft at its center. The shaft passes through two ball bearings set in a hub in the back of the outer tub, and a lip seal in front of the bearings keeps the wash water out of them.

A cut-away side view of a front-load washer. Labels show the outer tub, stainless drum with baffles, the spider bolted to the back of the drum, the shaft through two bearings and a seal in the rear tub hub, the drive pulley or direct-drive rotor behind the tub, the top springs, the bottom shock absorbers, the counterweights, the door boot and the door lock.
The tub, drum, spider, bearings and suspension of a front-load washer.

Behind the tub, the shaft drives either a large pulley, turned by a belt from a motor mounted under the tub, or the rotor of a direct-drive motor bolted straight onto the shaft, with its stator fixed to the back of the tub. Lesson 5 covers both. Either way, the bearings carry the whole weight of the drum and wet load and every bit of out-of-balance force in a spin.

Bearings and the seal

Front-load bearing failure has a typical history. The seal in front of the bearings wears, or is damaged by detergent residue and hard water, and lets a little wash water through. The water washes the grease out of the bearings, and they rust and wear. The first symptom is a rumble or roar during the spin that grows louder as the speed rises, often described by customers as sounding like a jet engine. As the wear progresses, the drum develops play: grab the top edge of the drum through the door and lift, and a worn bearing lets it move up and down. Rust-colored streaks down the back of the outer tub, below the hub, confirm water has been getting through the seal.

On many front-load washers the bearings and seal can be replaced, but only by separating the outer tub halves, which takes several hours, or by replacing the whole outer tub with new bearings already fitted. On others, the outer tub is a single welded piece and the bearings cannot be replaced at all; the only repair is a complete tub assembly. Because the water that killed the bearings has usually also corroded the spider, an aluminum spider is often inspected at the same time and replaced if its arms are pitted or cracked. A cracked spider arm can let the drum break loose at full spin.

Signs of bearing, seal and spider problems on a front-load washer.
SignWhat it suggests
Rumble or roar rising with spin speedWorn drum bearings
Drum lifts and drops at its top edgeBearing wear with play
Rust streaks on the back of the tub below the hubSeal leak washing out the bearings
Water dripping from the rear of the tubSeal failure
Loud bang during spin, scraping drumPossible spider arm crack; stop and inspect
Black flakes on clothesPossible spider corrosion or a degraded door boot

Worked problem

Repair or replace a washer with bad bearings

On Tuesday, September 22, Dee looked at Augustin Rolfe's 2016 front-load washer in Olde Towne East, which roared in spin. The drum moved about 1/8 in at its rim when lifted, and there were rust streaks below the tub hub. The bearings could only be replaced as a complete outer tub assembly. The part cost 430 dollars and Penfold's labor for the job was 3.5 hours at 110 dollars an hour, on top of the 95 dollar service call. A comparable new washer cost about 1,100 dollars installed. Using Penfold's rule of thumb, recommend replacement when a repair costs more than half the price of a new appliance on a unit over 8 years old. What should Dee recommend?

Show solution
  1. Labor: 3.5 × 110 = 385 dollars.
  2. Repair total before tax: 95 + 430 + 385 = 910 dollars.
  3. Half the price of a new washer: 1,100 ÷ 2 = 550 dollars.
  4. The washer is 10 years old, and 910 dollars is well over 550.

Answer: Dee recommended replacement. She explained the bearing failure, gave Mr. Rolfe the repair price in writing so he could decide, and charged the 95 dollar service call. He chose a new washer.

The rule of thumb is a starting point for the conversation, not a decision made for the customer. Some customers prefer to repair a washer they like, or one that matches a dryer, and some models are worth repairing at almost any age because parts are cheap and the build is robust. The technician's job is to give an honest diagnosis and a clear price, and to let the customer choose. APP-410 returns to repair-or-replace decisions.

Suspension, shocks and counterweights

A front-load tub hangs from two or more springs at the top and is damped by two or more shock absorbers, sometimes called dampers, at the bottom. The springs carry the weight; the dampers absorb the energy of vibration so that the tub does not keep swinging. Because the axis is horizontal, an unbalanced load tries to swing the whole tub in a circle at the drum speed. Heavy counterweights, usually concrete or cast iron, bolted to the front and top of the tub add mass so that the same unbalanced load moves the tub less. A full-size front-load tub assembly, with its weights, can weigh well over 110 lb.

Worn dampers are a common cause of a front-load washer that thumps, knocks the cabinet during spin or walks. A good damper resists being pushed and pulled by hand with a steady friction; a worn one moves freely or has lost its fluid or friction pad. Loose counterweight bolts make a knocking sound that customers often mistake for bearings. Broken or stretched springs let the tub sit low and hit the cabinet. Dampers are usually replaced in pairs. Before condemning the suspension, check that the washer is level, that all four feet are on the floor and their lock nuts tightened, and that the floor itself is not flexing.

Lesson 11 covers shipping bolts, which hold the tub rigid during delivery. A washer that has never had its shipping bolts removed shakes violently on its first spin, and the bolts must come out before the washer is used. A washer that suddenly shakes after a move may have had its tub damaged or its counterweight loosened in transit.

The door boot

The door boot, sometimes called the bellows or door gasket, is the folded rubber seal that joins the front of the outer tub to the cabinet opening. Its fold lets the tub move on its suspension while the cabinet stays still, and its lip seals against the door glass. Clamps hold it to the tub and the cabinet. Many boots have small drain holes at the bottom of the fold and, on some models, water spray nozzles that rinse the door glass.

The boot fails in three ways. It can tear or wear through, often at the bottom where coins, underwire from bras or other hard objects rub against it, and then leaks during the wash. It can grow mold in its folds where water and residue sit between washes. And it can harden and crack with age. A leaking front-loader with water on the floor in front of the machine during the wash is often a torn boot or a boot that has come off its clamp. Replacing a boot means removing the front panel and both clamps, and on some models the counterweight at the front, and care is needed to seat the new one evenly so that it seals all round.

The door lock

A front-load washer's door must not open while there is water above its bottom edge or while the drum is turning. The door lock is a switch assembly in the cabinet front that a strike on the door engages. A solenoid, a bimetal or wax actuator, or a small motor drives a pin to lock the strike, and a switch reports the locked state to the board. The washer will not fill or start until the lock reports locked, and will not unlock until the water level is safe and the drum has stopped. Many locks use a delay, so the door stays locked for a minute or two after the cycle ends.

A door that will not lock gives a door code at the start of the cycle and no fill. A door that will not unlock at the end is more alarming for the customer, who may have wet clothes trapped inside. First check that the cycle really has finished and drained; a washer that cannot drain will not unlock. Most door locks have a manual release cord or tab behind the front panel or the drain filter cover, which the use and care guide or tech sheet describes, for getting the clothes out after a failure. Like a lid lock, a door lock must never be bypassed.

Odor and mold

Front-load washers are prone to musty smells, and odor complaints are among the commonest calls they generate. The cause is almost always the same: a film of detergent residue, fabric softener and soil builds up on the outside of the drum, inside the outer tub, in the door boot folds and in the dispenser, and stays damp because the door is closed between washes. Mold and bacteria grow in that film and make the smell, and sometimes black spots appear in the boot. Cold-water washing, too much detergent, liquid softener and closing the door straight after a wash all make it worse.

The cure is mostly a matter of use, which the technician explains. Use HE detergent at the right dose, run the washer's tub-clean cycle, or a hot cycle with an approved washer cleaner, once a month, wipe the door boot dry after the last load of the day and leave the door and the dispenser drawer ajar so the inside can dry. Clean the drain pump filter, which lesson 4 covers, because standing water behind it adds to the smell. A boot whose folds are badly stained may need replacing. If a washer smells of sewage rather than mustiness, check for a drain hose pushed too far into the standpipe or a missing trap, which can let sewer gas back into the tub.

Moisture trapped behind clothes in a closed drum is also what makes a front-loader's door boot mold. Harriet's advice to customers is short: "Leave it open to dry, use less soap and run the clean cycle once a month." On a customer visit, Penfold technicians leave the use and care page with those steps open, because a customer who sees it in writing is more likely to do it.

Leveling and the floor

Many front-load vibration complaints are not about the washer at all. A front-loader spinning at 1,200 rpm needs to stand firmly on all four feet on a solid, level floor. Check level side to side and front to back with a spirit level on the top panel, adjust the feet so that all four carry weight, and tighten each foot's lock nut against the cabinet so the foot cannot turn back. A washer that rocks when pressed on diagonally opposite corners has a foot off the floor. On a wooden floor, a washer near the middle of a long joist span can make the whole floor bounce; the use and care guide may suggest a plywood base or moving the washer closer to a wall, and some makers sell anti-vibration pads. Pedestals raise the washer and make vibration worse if they are not the maker's own and properly fastened.

Before ordering dampers or bearings for a noisy front-loader, run a spin with a balanced load of towels and watch the cabinet. A tub that moves smoothly while the cabinet stays still is working as designed. A cabinet that shakes or a floor that bounces points to the feet and the floor first.

Common mistakes

  • MistakeCalling a loose counterweight a bearing failure.

    InsteadCheck the weight bolts and listen for a knock rather than a rising roar.

  • MistakeReplacing bearings without inspecting the spider.

    InsteadLook for pitting and cracks in the spider arms; replace a damaged spider.

  • MistakeReplacing a single damper.

    InsteadReplace dampers in pairs.

  • MistakeForcing a locked door.

    InsteadCheck that the washer has drained, then use the manual release the tech sheet describes.

  • MistakeTreating odor as a part failure.

    InsteadExplain detergent dose, the clean cycle and drying the boot and drum.

  • MistakeMaking the repair decision for the customer.

    InsteadGive the diagnosis and a written price, and let the customer choose.

Summary and key terms

  • A front-load drum is carried by a spider whose shaft runs in two bearings behind a seal in the rear of the tub.
  • A failed seal lets water wash out the bearings; the result is a roar rising with spin speed and play in the drum.
  • Many front-load bearings can only be replaced with the outer tub; inspect the spider too.
  • Springs carry the tub, dampers absorb vibration and counterweights reduce movement.
  • The door boot seals the tub to the cabinet and tears, molds or hardens with age.
  • The door lock must report locked before the washer fills and stays locked until the water is down and the drum stopped.
  • Odor comes from residue in a damp, closed washer; detergent dose, clean cycles and drying fix it.
Spider
The three-armed casting bolted to the back of a front-load drum, carrying the drive shaft.
Drum bearing
One of the ball bearings in the rear tub hub that carry the drum shaft.
Tub seal
The lip seal in front of the drum bearings that keeps wash water out of them.
Damper
A friction or fluid shock absorber that damps the movement of a front-load tub.
Counterweight
A heavy block bolted to a front-load tub to reduce its movement in spin.
Door boot
The folded rubber seal joining the front of a front-load tub to the cabinet.
Door lock
The switch assembly that locks a front-load door and reports the locked state to the control.
Tub-clean cycle
A cycle that runs hot water and cleaner through an empty washer to remove residue.

Practice problems

Work each problem on paper first, then reveal the answer to check.

  1. What is the usual chain of events that ends in a front-load bearing failure?

    Show answer

    The seal wears, water washes the grease out, and the bearings rust and wear.

  2. How can you check a front-load drum for bearing play?

    Show answer

    Lift the top edge of the drum and feel for up-and-down movement.

  3. Why must the spider be inspected during a bearing repair?

    Show answer

    The same water corrodes it, and a cracked arm can let the drum break loose.

  4. A front-loader leaks onto the floor in front during the wash. What should you check first?

    Show answer

    The door boot for tears and correct clamping.

  5. A customer complains of a musty smell. What do you recommend?

    Show answer

    Correct HE detergent dose, monthly clean cycles, drying the boot and leaving the door ajar.

Lesson quiz · 5 questions

Score 60% or more to complete this lesson.

Take the quiz