Surface facilities, produced water and emissions

Sofia Reyes, the facilities engineer, joins Ethan at the Tamarack battery to walk the equipment that will receive the 04-22's production for the next twenty years. 'Everything you do downhole ends up here,' she says. 'If you double the water rate, I need treater capacity. If you put the well on gas lift, I need compression. And every cubic metre of gas we vent now counts against a federal methane limit. Production and facilities engineers have to plan together.'

This lesson covers the main surface facilities for oil and gas wells, the sizing of separators, the treatment of oil emulsions and produced water, flow assurance problems such as corrosion, scale, paraffin and hydrates, and the rules on flaring, venting and methane emissions in Canada and the United States.

What a facility does

A production facility, called a battery in Canada and often a tank battery or pad facility in the United States, receives the mixed stream from one or more wells and turns it into saleable oil, saleable or usable gas, and water ready for disposal or injection. The typical sequence is a separator to split gas from liquid, a treater to break oil-water emulsions and remove water from the oil, storage tanks for oil, gas measurement and compression, and water storage and pumps. Each stream is measured for sales, royalties and regulatory reports. Larger fields have central facilities fed by gathering systems, with gas sent to a processing plant that removes liquids, water and sour components.

Separators

A separator is a pressure vessel in which gas and liquid are given time and space to part. Most separators have four sections: an inlet device that knocks the momentum out of the incoming stream and makes a first split; a gravity settling section where droplets fall out of the gas; a mist extractor, a mesh pad or vane pack that captures the fine droplets that remain; and a liquid collection section where gas bubbles rise out of the liquid. Two-phase separators split gas from total liquid; three-phase separators also split oil from water, using weirs or interface controls.

Separators are sized for two duties. The gas capacity is set by the velocity at which the largest droplets that must be captured can still settle against the upward gas flow. The Souders-Brown equation expresses this allowable velocity with an empirical coefficient K that depends on the vessel type and mist extractor.

The liquid capacity is set by retention time: the liquid must stay in the vessel long enough for gas to break out and, in three-phase separators, for oil and water to separate. Typical retention times are one to three minutes for two-phase separation of light oil and five to ten minutes or more for three-phase separation or foamy, viscous oils. The vessel must also hold slugs arriving from the flowline without flooding the gas outlet, which often controls the size more than steady flow does.

# Surface facilities: separator gas capacity (Souders-Brown) and liquid retention, treater heat duty,
# and an emissions check for the new well
import math
SI = True   
if SI:   # 04-22 test separator at the Tamarack battery; SI throughout
    qg, ql, qo, qw, p, T = 5600.0, 66.0, 52.0, 14.0, 550.0, 288.0   # m3/d, kPa (gauge), K
    vent, ch4 = 120.0, 0.72                                          # tank-flash gas vented, m3/d; methane fraction
    sl = lambda m: f"{m:,.2f} m"; sv = lambda v: f"{v:,.2f} m3"; sq = lambda x: f"{x:,.0f} m3/d"
    sk = lambda kw: f"{kw:,.0f} kW"
else:    # 4-22H pad separator; computed in SI, shown in field units
    qg, ql, qo, qw, p, T = 900 * 28.317, 1610 / 6.2898, 1050 / 6.2898, 560 / 6.2898, 160 * 6.89476, 290.0
    flared, goal = 70.0, 0.91                                        # Mscf/d flared when the gas line is down part of the month
    sl = lambda m: f"{m / 0.3048:,.1f} ft"; sv = lambda v: f"{v * 6.2898:,.0f} bbl"; sq = lambda x: f"{x * 6.2898:,.0f} bbl/d"
    sk = lambda kw: f"{kw * 3412 / 1e6:,.2f} MMBtu/h"
P = p + 101.325
rho_g = P * 1000 * 28.97 * 0.75 / (0.95 * 8314 * T)       # kg/m3, gas gravity about 0.75
rho_l = 870.0
K = 0.11                                                  # m/s, vertical separator with a mist extractor (typical range)
vt = K * math.sqrt((rho_l - rho_g) / rho_g)
qg_act = qg * (101.325 / P) * (T / 288.7) * 0.95 / 86400   # m3/s at separator conditions
D = math.sqrt(4 * qg_act / (math.pi * vt))
print(f"gas density {rho_g:.1f} kg/m3; allowable gas velocity {vt:.2f} m/s; minimum vessel diameter for gas {sl(D)}")
for minutes in (3, 10):
    print(f"   liquid volume for {minutes:2d} min retention: {sv(ql * minutes / 1440)}")
duty = (qo * 870 * 2.0 + qw * 1050 * 4.18) * 1000 * (60 - 15) / 86400 / 1000   # kW to heat from 15 to 60 C (kJ/kg.K)
print(f"treater heat to warm the emulsion by 45 degrees C (81 F): about {sk(duty)} before heat recovery")
if SI:
    intensity = vent * ch4 / qg
    print(f"tank vent {sq(vent)} at {ch4:.0%} methane = {intensity:.2%} of produced gas as vented methane")
    print("   the federal performance pathway cited for production facilities is 0.20%; vapour recovery or combustion is needed")
else:
    prod = 900.0; cap = (prod - flared) / prod
    print(f"gas capture {cap:.1%} (produced {prod:,.0f} Mscf/d, flared {flared:,.0f}) against the state goal of {goal:.0%}")

gas density 6.2 kg/m3; allowable gas velocity 1.30 m/s; minimum vessel diameter for gas 0.10 m
   liquid volume for  3 min retention: 0.14 m3
   liquid volume for 10 min retention: 0.46 m3
treater heat to warm the emulsion by 45 degrees C (81 F): about 79 kW before heat recovery
tank vent 120 m3/d at 72% methane = 1.54% of produced gas as vented methane
   the federal performance pathway cited for production facilities is 0.20%; vapour recovery or combustion is needed

For the 04-22 alone, the gas capacity barely matters: a vessel only about 0.10 m across could carry the gas. The liquid duty is also modest, under half a cubic metre for ten minutes of retention. Real separators are much larger, because they serve several wells, must absorb slugs and flowback surges, and come in standard sizes. Sofia's existing test separator at the battery has ample room. The treater is a different matter: warming the emulsion by 45 °C needs about 79 kW before heat recovery, and the treater's burner is already close to its limit in winter.

Treating oil and water

Water produced with oil often forms an emulsion, droplets of water dispersed in the oil, stabilized by natural surfactants, fine solids and asphaltenes. Sales contracts limit the water and sediment in crude, often to less than 0.5 to 1 percent. Heater-treaters break emulsions by combining heat, which lowers oil viscosity and weakens the films around droplets; demulsifier chemicals, which displace the natural stabilizers; time; and sometimes electrostatic grids that make droplets coalesce. Free-water knockouts upstream remove water that separates easily and save heating it.

Produced water is the largest volume stream in most mature oil fields, often several barrels or cubic metres of water for each one of oil. It carries dissolved salts, sometimes at concentrations several times that of seawater in basins such as the Williston, along with dispersed oil, solids, bacteria and naturally occurring radioactive material. It is treated to remove oil and solids and then either injected into the reservoir for pressure maintenance or waterflooding, or injected into approved disposal zones. Discharge to surface water is generally not permitted onshore. Water handling is often the main constraint on a field's capacity, and its cost per barrel can exceed the cost of lifting the oil.

Flow assurance

Flow assurance covers the problems that restrict flow in wells, lines and facilities, and the production engineer works on them daily.

Corrosion comes mainly from carbon dioxide forming carbonic acid in water, hydrogen sulphide causing pitting and cracking, oxygen entering through vents or injection water, and bacteria. It is managed with corrosion-resistant materials, coatings, chemical inhibitors injected continuously or in batches, cathodic protection for buried lines, and monitoring with coupons and probes. Under-deposit corrosion beneath scale or sludge is a common cause of flowline leaks.

Scale forms when dissolved minerals precipitate as pressure and temperature change or when incompatible waters mix: calcium carbonate where CO₂ comes out of solution, barium and strontium sulphate where sulphate-rich injection water meets barium-rich formation water, and in some fields, halite from very salty brines. Scale chokes perforations, pumps, tubing and valves. It is prevented with inhibitors, sometimes squeezed into the formation, and removed with acid or mechanical milling. Bakken wells are known for halite deposition, and operators often inject fresh water continuously to keep salt in solution.

Paraffin and asphaltenes deposit from crude oils as they cool or as pressure falls. Paraffin forms waxy deposits in tubing and flowlines below the oil's cloud point, especially in cold climates. Remedies include hot oiling, scraping with mechanical cutters, chemical inhibitors and insulated or heated lines. Asphaltenes come out of solution near the bubble point and are harder to treat.

Hydrates are ice-like solids of water and light gases that form at high pressure and low temperature, often in gas lines and chokes in winter. They are prevented with methanol or glycol injection, heating or keeping the water out.

Sand and solids erode chokes and pumps and fill separators. Good completion practice limits them, and facilities use sand traps, desanders and cyclones where they persist.

Flaring, venting and methane

Gas that cannot be sold or used is either flared, burned at a flare stack or enclosed combustor, or vented directly to the air. Methane is a powerful greenhouse gas, so venting is now tightly restricted in both countries, and flaring is limited by gas conservation rules. Both countries have committed to deep cuts in oil and gas methane emissions.

In Alberta, the Alberta Energy Regulator (AER) sets flaring, incinerating and venting requirements in Directive 060, including limits on routine venting and requirements for leak detection and repair. Federally, Canada published enhanced methane regulations for the oil and gas sector at the end of 2025. They require the near-elimination of methane venting by 1 January 2030, prohibit venting at facilities that begin operating after 1 January 2028, and offer two compliance routes: a prescriptive route with defined leak inspections and repair timelines, and a performance-based route with emission intensity limits, cited at 0.20 percent of produced gas for production facilities. Provinces can run their own rules under equivalency agreements; a Canada-Alberta memorandum of understanding in November 2025 committed Alberta to an equivalency agreement aiming for a 75 percent cut from 2014 levels by 2035. Details are still being finalized, so production engineers follow the current version of the rules closely.

The program shows why the Tamarack battery's tank vents matter. If 120 m³/d of flash gas from the oil tanks were vented at 72 percent methane, the vented methane would be about 1.5 percent of the gas produced, more than seven times the 0.20 percent intensity cited for the performance route. Sofia's vapour recovery project would capture that gas and send it to sales, removing the vent and recovering gas that has value.

Leak detection and measurement

Much of the methane from oil and gas operations comes not from routine venting but from leaks and malfunctions: stuck dump valves on separators that let gas reach tanks, open thief hatches, leaking compressor seals and pneumatic controllers that bleed gas. Leak detection and repair (LDAR) programs use optical gas imaging cameras, handheld analysers and, increasingly, continuous sensors, aircraft and satellites to find leaks so they can be fixed quickly. Replacing gas-driven pneumatic devices with electric or instrument-air ones removes a large source of routine emissions. Production engineers contribute by designing wells and facilities that do not need to vent, by setting separator and tank pressures that limit flash losses, and by tracking emissions as closely as production.